Alex: Please look at the posts from the past week. It's the same problem, and a fix is forthcoming.
-Mike On Tue, 16 Jun 2009, Alex Kilgore wrote: > Hi, > Recently I updated my kernel from 2.6.29.3 to 2.6.30, and my > WinTV PVR USB2 picture is now no longer correct, it has red, blue and green > vertical lines going down it and only about half of it appears > > It looks *fine* when i read from /dev/video0 with mplayer > but when I use mythtv, the picture is distorted (amd then after quitting, even > using mplayer, it shows the same symptom) until I reload the pvrusb2 module, I > would think that this is some sort of configuration error with mythtv, except > for the fact that it operates fine when i move back to kernel 2.6.29.3 > > This is the output when the card is detected > > [ 6.156355] cx25840 1-0044: firmware: requesting v4l-cx25840.fw > [ 6.929460] cx25840 1-0044: loaded v4l-cx25840.fw firmware (12559 bytes) > [ 6.967078] tveeprom 1-00a2: Hauppauge model 24012, rev C3A3, serial# > 8579815 > [ 6.967083] tveeprom 1-00a2: tuner model is TCL MFNM05-4 (idx 103, > type 43) > [ 6.967088] tveeprom 1-00a2: TV standards NTSC(M) (eeprom 0x08) > [ 6.967091] tveeprom 1-00a2: audio processor is CX25843 (idx 37) > [ 6.967095] tveeprom 1-00a2: decoder processor is CX25843 (idx 30) > [ 6.967099] tveeprom 1-00a2: has radio, has IR receiver, has no IR > transmitter > [ 6.967106] pvrusb2: Supported video standard(s) reported available > in hardware: PAL-M/N/Nc;NTSC-M/Mj/Mk > [ 6.967111] pvrusb2: Mapping standards mask=0xb700 > (PAL-M/N/Nc;NTSC-M/Mj/Mk) > [ 6.967115] pvrusb2: Setting up 6 unique standard(s) > [ 6.967119] pvrusb2: Set up standard idx=0 name=PAL-M > [ 6.967122] pvrusb2: Set up standard idx=1 name=PAL-N > [ 6.967126] pvrusb2: Set up standard idx=2 name=PAL-Nc > [ 6.967130] pvrusb2: Set up standard idx=3 name=NTSC-M > [ 6.967133] pvrusb2: Set up standard idx=4 name=NTSC-Mj > [ 6.967137] pvrusb2: Set up standard idx=5 name=NTSC-Mk > [ 6.967141] pvrusb2: Initial video standard guessed as NTSC-M > [ 6.967152] pvrusb2: Device initialization completed successfully. > [ 6.967231] pvrusb2: registered device video0 [mpeg] > [ 6.967255] pvrusb2: registered device radio0 [mpeg] > [ 6.967945] usb 1-5.4: firmware: requesting v4l-cx2341x-enc.fw > [ 7.311324] tuner-simple 1-0061: creating new instance > [ 7.311328] tuner-simple 1-0061: type set to 43 (Philips NTSC MK3 > (FM1236MK3 or FM1236/F)) > > Has anyone else experienced similar issues? > Thanks for your time > Alex > > > _______________________________________________ > pvrusb2 mailing list > [email protected] > http://www.isely.net/cgi-bin/mailman/listinfo/pvrusb2 > -- Mike Isely isely @ isely (dot) net PGP: 03 54 43 4D 75 E5 CC 92 71 16 01 E2 B5 F5 C1 E8 _______________________________________________ pvrusb2 mailing list [email protected] http://www.isely.net/cgi-bin/mailman/listinfo/pvrusb2
