Mike,
Oh, okay, I looked through those initially, but probably should have
read the thread more carefully!, my apologies, and thanks for your time!
Alex
Mike Isely wrote:
Alex:
Please look at the posts from the past week. It's the same problem, and
a fix is forthcoming.
-Mike
On Tue, 16 Jun 2009, Alex Kilgore wrote:
Hi,
Recently I updated my kernel from 2.6.29.3 to 2.6.30, and my
WinTV PVR USB2 picture is now no longer correct, it has red, blue and green
vertical lines going down it and only about half of it appears
It looks *fine* when i read from /dev/video0 with mplayer
but when I use mythtv, the picture is distorted (amd then after quitting, even
using mplayer, it shows the same symptom) until I reload the pvrusb2 module, I
would think that this is some sort of configuration error with mythtv, except
for the fact that it operates fine when i move back to kernel 2.6.29.3
This is the output when the card is detected
[ 6.156355] cx25840 1-0044: firmware: requesting v4l-cx25840.fw
[ 6.929460] cx25840 1-0044: loaded v4l-cx25840.fw firmware (12559 bytes)
[ 6.967078] tveeprom 1-00a2: Hauppauge model 24012, rev C3A3, serial#
8579815
[ 6.967083] tveeprom 1-00a2: tuner model is TCL MFNM05-4 (idx 103,
type 43)
[ 6.967088] tveeprom 1-00a2: TV standards NTSC(M) (eeprom 0x08)
[ 6.967091] tveeprom 1-00a2: audio processor is CX25843 (idx 37)
[ 6.967095] tveeprom 1-00a2: decoder processor is CX25843 (idx 30)
[ 6.967099] tveeprom 1-00a2: has radio, has IR receiver, has no IR
transmitter
[ 6.967106] pvrusb2: Supported video standard(s) reported available
in hardware: PAL-M/N/Nc;NTSC-M/Mj/Mk
[ 6.967111] pvrusb2: Mapping standards mask=0xb700
(PAL-M/N/Nc;NTSC-M/Mj/Mk)
[ 6.967115] pvrusb2: Setting up 6 unique standard(s)
[ 6.967119] pvrusb2: Set up standard idx=0 name=PAL-M
[ 6.967122] pvrusb2: Set up standard idx=1 name=PAL-N
[ 6.967126] pvrusb2: Set up standard idx=2 name=PAL-Nc
[ 6.967130] pvrusb2: Set up standard idx=3 name=NTSC-M
[ 6.967133] pvrusb2: Set up standard idx=4 name=NTSC-Mj
[ 6.967137] pvrusb2: Set up standard idx=5 name=NTSC-Mk
[ 6.967141] pvrusb2: Initial video standard guessed as NTSC-M
[ 6.967152] pvrusb2: Device initialization completed successfully.
[ 6.967231] pvrusb2: registered device video0 [mpeg]
[ 6.967255] pvrusb2: registered device radio0 [mpeg]
[ 6.967945] usb 1-5.4: firmware: requesting v4l-cx2341x-enc.fw
[ 7.311324] tuner-simple 1-0061: creating new instance
[ 7.311328] tuner-simple 1-0061: type set to 43 (Philips NTSC MK3
(FM1236MK3 or FM1236/F))
Has anyone else experienced similar issues?
Thanks for your time
Alex
_______________________________________________
pvrusb2 mailing list
[email protected]
http://www.isely.net/cgi-bin/mailman/listinfo/pvrusb2
_______________________________________________
pvrusb2 mailing list
[email protected]
http://www.isely.net/cgi-bin/mailman/listinfo/pvrusb2
