On Mon, Aug 18, 2025 at 10:46:00AM -0400, Jonah Palmer wrote: > > > On 8/18/25 2:51 AM, Eugenio Perez Martin wrote: > > On Fri, Aug 15, 2025 at 4:50 PM Jonah Palmer <jonah.pal...@oracle.com> > > wrote: > > > > > > > > > > > > On 8/14/25 5:28 AM, Eugenio Perez Martin wrote: > > > > On Wed, Aug 13, 2025 at 4:06 PM Peter Xu <pet...@redhat.com> wrote: > > > > > > > > > > On Wed, Aug 13, 2025 at 11:25:00AM +0200, Eugenio Perez Martin wrote: > > > > > > On Mon, Aug 11, 2025 at 11:56 PM Peter Xu <pet...@redhat.com> wrote: > > > > > > > > > > > > > > On Mon, Aug 11, 2025 at 05:26:05PM -0400, Jonah Palmer wrote: > > > > > > > > This effort was started to reduce the guest visible downtime by > > > > > > > > virtio-net/vhost-net/vhost-vDPA during live migration, > > > > > > > > especially > > > > > > > > vhost-vDPA. > > > > > > > > > > > > > > > > The downtime contributed by vhost-vDPA, for example, is not > > > > > > > > from having to > > > > > > > > migrate a lot of state but rather expensive backend > > > > > > > > control-plane latency > > > > > > > > like CVQ configurations (e.g. MQ queue pairs, RSS, MAC/VLAN > > > > > > > > filters, offload > > > > > > > > settings, MTU, etc.). Doing this requires kernel/HW NIC > > > > > > > > operations which > > > > > > > > dominates its downtime. > > > > > > > > > > > > > > > > In other words, by migrating the state of virtio-net early > > > > > > > > (before the > > > > > > > > stop-and-copy phase), we can also start staging backend > > > > > > > > configurations, > > > > > > > > which is the main contributor of downtime when migrating a > > > > > > > > vhost-vDPA > > > > > > > > device. > > > > > > > > > > > > > > > > I apologize if this series gives the impression that we're > > > > > > > > migrating a lot > > > > > > > > of data here. It's more along the lines of moving control-plane > > > > > > > > latency out > > > > > > > > of the stop-and-copy phase. > > > > > > > > > > > > > > I see, thanks. > > > > > > > > > > > > > > Please add these into the cover letter of the next post. IMHO > > > > > > > it's > > > > > > > extremely important information to explain the real goal of this > > > > > > > work. I > > > > > > > bet it is not expected for most people when reading the current > > > > > > > cover > > > > > > > letter. > > > > > > > > > > > > > > Then it could have nothing to do with iterative phase, am I right? > > > > > > > > > > > > > > What are the data needed for the dest QEMU to start staging > > > > > > > backend > > > > > > > configurations to the HWs underneath? Does dest QEMU already > > > > > > > have them in > > > > > > > the cmdlines? > > > > > > > > > > > > > > Asking this because I want to know whether it can be done > > > > > > > completely > > > > > > > without src QEMU at all, e.g. when dest QEMU starts. > > > > > > > > > > > > > > If src QEMU's data is still needed, please also first consider > > > > > > > providing > > > > > > > such facility using an "early VMSD" if it is ever possible: feel > > > > > > > free to > > > > > > > refer to commit 3b95a71b22827d26178. > > > > > > > > > > > > > > > > > > > While it works for this series, it does not allow to resend the > > > > > > state > > > > > > when the src device changes. For example, if the number of > > > > > > virtqueues > > > > > > is modified. > > > > > > > > > > Some explanation on "how sync number of vqueues helps downtime" would > > > > > help. > > > > > Not "it might preheat things", but exactly why, and how that differs > > > > > when > > > > > it's pure software, and when hardware will be involved. > > > > > > > > > > > > > By nvidia engineers to configure vqs (number, size, RSS, etc) takes > > > > about ~200ms: > > > > https://urldefense.com/v3/__https://lore.kernel.org/qemu-devel/6c8ebb97-d546-3f1c-4cdd-54e23a566...@nvidia.com/T/__;!!ACWV5N9M2RV99hQ!OQdf7sGaBlbXhcFHX7AC7HgYxvFljgwWlIgJCvMgWwFvPqMrAMbWqf0862zV5shIjaUvlrk54fLTK6uo2pA$ > > > > > > > > Adding Dragos here in case he can provide more details. Maybe the > > > > numbers have changed though. > > > > > > > > And I guess the difference with pure SW will always come down to PCI > > > > communications, which assume it is slower than configuring the host SW > > > > device in RAM or even CPU cache. But I admin that proper profiling is > > > > needed before making those claims. > > > > > > > > Jonah, can you print the time it takes to configure the vDPA device > > > > with traces vs the time it takes to enable the dataplane of the > > > > device? So we can get an idea of how much time we save with this. > > > > > > > > > > Let me know if this isn't what you're looking for. > > > > > > I'm assuming by "configuration time" you mean: > > > - Time from device startup (entry to vhost_vdpa_dev_start()) to right > > > before we start enabling the vrings (e.g. > > > VHOST_VDPA_SET_VRING_ENABLE in vhost_vdpa_net_cvq_load()). > > > > > > And by "time taken to enable the dataplane" I'm assuming you mean: > > > - Time right before we start enabling the vrings (see above) to right > > > after we enable the last vring (at the end of > > > vhost_vdpa_net_cvq_load()) > > > > > > Guest specs: 128G Mem, SVQ=on, CVQ=on, 8 queue pairs: > > > > > > -netdev type=vhost-vdpa,vhostdev=$VHOST_VDPA_0,id=vhost-vdpa0, > > > queues=8,x-svq=on > > > > > > -device virtio-net-pci,netdev=vhost-vdpa0,id=vdpa0,bootindex=-1, > > > romfile=,page-per-vq=on,mac=$VF1_MAC,ctrl_vq=on,mq=on, > > > ctrl_vlan=off,vectors=18,host_mtu=9000, > > > disable-legacy=on,disable-modern=off > > > > > > --- > > > > > > Configuration time: ~31s > > > Dataplane enable time: ~0.14ms > > > > > > > I was vague, but yes, that's representative enough! It would be more > > accurate if the configuration time ends by the time QEMU enables the > > first queue of the dataplane though. > > > > As Si-Wei mentions, is v->shared->listener_registered == true at the > > beginning of vhost_vdpa_dev_start? > > > > Ah, I also realized that Qemu I was using for measurements was using a > version before the listener_registered member was introduced. > > I retested with the latest changes in Qemu and set x-svq=off, e.g.: guest > specs: 128G Mem, SVQ=off, CVQ=on, 8 queue pairs. I ran testing 3 times for > measurements. > > v->shared->listener_registered == false at the beginning of > vhost_vdpa_dev_start(). > > --- > > Configuration time: Time from first entry into vhost_vdpa_dev_start() to > right after Qemu enables the first VQ. > - 26.947s, 26.606s, 27.326s
It's surprising to know it takes 20+ seconds for one device to load. Sorry I'm not familiar with CVQ, please bare with me on my ignorance: how much CVQ=on contributes to this? Is page pinning involved here? Is 128GB using small pages only? It looks to me there can still be many things that vDPA will face similar challenges that VFIO already had. For example, there's current work optimizing pinning for VFIO here: https://lore.kernel.org/all/20250814064714.56485-1-lizhe...@bytedance.com/ For the long term, not sure if (for either VFIO or vDPA, or similar devices that needs guest pinning) it would make more sense to start using 1G huge pages just for the sake of fast pinning. PFNMAP in VFIO already works with 1G pfnmaps with commit eb996eec783c. Logically if we could use 1G pages (e.g. on x86_64) for guest, then pinning / unpinning can also be easily batched, and DMA pinning should be much faster. The same logic may also apply to vDPA if it works the similar way. The work above was still generic, but I mentioned the idea of optimizing for 1G huge pages here: https://lore.kernel.org/all/aC3z_gUxJbY1_JP7@x1.local/#t Above is just FYI.. definitely not an request to work on that. So if we can better split the issue into smaller but multiple scope of works it would be nicer. The "iterable migratable virtio-net" might just hide too many things under the hood. > > Enable dataplane: Time from right after first VQ is enabled to right after > the last VQ is enabled. > - 0.081ms, 0.081ms, 0.079ms > The other thing that might worth mention.. from migration perspective, VFIO used to introduce one feature called switchover-ack: # @switchover-ack: If enabled, migration will not stop the source VM # and complete the migration until an ACK is received from the # destination that it's OK to do so. Exactly when this ACK is # sent depends on the migrated devices that use this feature. For # example, a device can use it to make sure some of its data is # sent and loaded in the destination before doing switchover. # This can reduce downtime if devices that support this capability # are present. 'return-path' capability must be enabled to use # it. (since 8.1) If above 20+ seconds are not avoidable, not sure if virtio-net would like to opt-in in this feature too, so that switchover won't happen too soon during an pre-mature preheat, so that won't be accounted into downtime. Again, just FYI. I'm not sure if it's applicable. Thanks, -- Peter Xu
