That doesn't sound quite right, the stop should hit before the butterfly hits the side.
Any sign that somebody has adjusted the throttle stop or bent the stop arm ?

Jim


On 11/06/2010 14:41, geoff ward wrote:
Been out side this afternoon and checked the butterfly. It is completely closed just before the stop is reached.
Regards, Geoff.

On 11 June 2010 08:49, Jim Hearne <[email protected] <mailto:[email protected]>> wrote:

    The injector to manifold seals aren't O rings, they are about 15mm
    dia made of silicone rubber and fit into holes on the manifold.
    The ends of the injectors then locate into those.
    I'm sure the plastic inlet manifold and metal manifold have
    different seals which is why i'm wondering which ones you ended up
    with.
    They can also leak if reused, we had that on Matthews car which we
    found using the hose.

    The charcol canister is under the boot floor but the solenoid is
    at the rear of the engine bay attached via a vacumn hose.

    Jim



    On 10/06/2010 22:36, geoff ward wrote:
    Hi Jim,
    Nothing to report I am afraid. The one thing I was supposed to
    do, check that the throttle butterfly closes completely, I have
    not had the opportunity to do. I have had my first few days back
    at work and it has been to wet in the evenings. Steve must be
    very busy at work because he has not found time to reply to your
    previous posting. I will do my best to answer your questions.
    If the seals you refer to are small round rubber O rings, I do
    remember them being in place.
    We used red gasket sealant because we reused the old gaskets from
    the aluminium manifold or in one case cut a new one from gasket
    paper, and thought it would be best to use the sealant as well.
    Did not check this valve, I think, but engine was working OK when
    in the Escort.
    Don't recall this canister or the solenoid on the manifold when
    we stripped the Escort.
    Regards, Geoff.

    On 10 June 2010 10:01, Jim Hearne <[email protected]
    <mailto:[email protected]>> wrote:

        Any progress ?


        Jim




        On 07/06/2010 10:19, geoff ward wrote:
        Hi all and thanks again for all the helpful suggestions.
        Steve and I have checked and double checked through all that
        has been suggested, every thing seems to work as it should
        individually. The idle speed control vale has been
        thoroughly cleaned again and checked to see that it works,
        then refitted with a new gasket and that it receives input,
        electronically, from its plug. Steve has checked all the
        connections with his testing equipment, it's all beyond me!,
        and it all works. We have reset the ECU yet again, despite
        spending all day Saturday trying to get it to run properly,
        it still has the same problem.
        Thank you Steve for all the time and effort you have put in
        so far to try and fix it.
        So if any of you have any further suggestions, we would be
        pleased to hear them, as Carole and I are getting worried
        now, with only one weekend to go before we head to Scotland.
        Yours hopefully Geoff.

        On 1 June 2010 22:59, geoff ward <[email protected]
        <mailto:[email protected]>> wrote:

            Thank you to all for your help and advice, I will do a
bit more checking and cleaning of contacts etc tomorrow. The strangest thing,as Steve mentioned in his
            original post, is that the engine idles perfectly
            at around 900 - 1000 rpm (according to the XR2 rev
            counter) when you first start it up. I have followed the
            method for resetting the ECU 4 times know and it has had
            good idle speed every time for the first stage of the
            reset, ie allow to idle for 10 -15 mins (DO NOT TOUCH
            THE THROTTLE) it only goes all wrong after that! As soon
            as you start to drive it, that's when it wont idle
            properly anymore.
            Carole say thank you all.
            Regards, Geoff.
            On 1 June 2010 12:29, Steve Kodz <[email protected]
            <mailto:[email protected]>> wrote:

                We're getting a very bad idle with the Zetec in
                Carole's 2+2.  With the idle
                speed control valve connected from cold it will idle
                nicely at around
                1000rpm, if just left to idle and warm through.
                 However if you rev, or
                drive that car the best idle to can get is between
                2-3,000 rpm, which isn't
                great :(  The car also drives badly, having
                hesitation and then you fight
                the engine on the over run.

                It is a lot better with the ISCV disconnected, but
                still not great.  The
                idle is still a bit high, being around 1,200 rpm and
                it still doesn't drive
                that great.

                We've tried resetting the ECU to re-program it and
                Geoff's cleaned all the
                electrical contact and the ISCV.  Any ideas what
                else needs to be done to
                get this ready before the HHII?

                Regards,
                Steve
                --
                www.h4-turbo.co.uk <http://www.h4-turbo.co.uk/>
                www.quantumowners.co.uk
                <http://www.quantumowners.co.uk/>
                www.quantumcars.co.uk <http://www.quantumcars.co.uk/>
                www.quantumheritage.co.uk
                <http://www.quantumheritage.co.uk/>

                --
                You received this message because you are subscribed
                to the Google Groups "Quantum Owners Group" group.
                To post to this group, send email to
                [email protected]
                <mailto:[email protected]>
                To unsubscribe from this group, send email to
                [email protected]
                <mailto:[email protected]>
                For more options, visit this group at
                http://groups.google.com/group/quantumowners?hl=en

                IMPORTANT NOTE: All information presented herewith
                is provided on an "As Is" basis, without warranty or
                the implication thereof. Neither the Quantum Owners
                Club nor the individuals associated with the Quantum
                Owners Club or in the preparation of the above
                information shall have any liability to any person
                or entity with respect to liability, loss, or damage
                caused or alleged to be caused directly or
                indirectly by the instructions contained within this
                or related message(s).



-- You received this message because you are subscribed to the
        Google Groups "Quantum Owners Group" group.
        To post to this group, send email to
        [email protected]
        <mailto:[email protected]>
        To unsubscribe from this group, send email to
        [email protected]
        <mailto:[email protected]>
        For more options, visit this group at
        http://groups.google.com/group/quantumowners?hl=en

        IMPORTANT NOTE: All information presented herewith is
        provided on an "As Is" basis, without warranty or the
        implication thereof. Neither the Quantum Owners Club nor the
        individuals associated with the Quantum Owners Club or in
        the preparation of the above information shall have any
        liability to any person or entity with respect to liability,
        loss, or damage caused or alleged to be caused directly or
        indirectly by the instructions contained within this or
        related message(s).
-- You received this message because you are subscribed to the
        Google Groups "Quantum Owners Group" group.
        To post to this group, send email to
        [email protected]
        <mailto:[email protected]>
        To unsubscribe from this group, send email to
        [email protected]
        <mailto:[email protected]>
        For more options, visit this group at
        http://groups.google.com/group/quantumowners?hl=en

        IMPORTANT NOTE: All information presented herewith is
        provided on an "As Is" basis, without warranty or the
        implication thereof. Neither the Quantum Owners Club nor the
        individuals associated with the Quantum Owners Club or in the
        preparation of the above information shall have any liability
        to any person or entity with respect to liability, loss, or
        damage caused or alleged to be caused directly or indirectly
        by the instructions contained within this or related message(s).


-- You received this message because you are subscribed to the
    Google Groups "Quantum Owners Group" group.
    To post to this group, send email to
    [email protected]
    <mailto:[email protected]>
    To unsubscribe from this group, send email to
    [email protected]
    <mailto:[email protected]>
    For more options, visit this group at
    http://groups.google.com/group/quantumowners?hl=en

    IMPORTANT NOTE: All information presented herewith is provided on
    an "As Is" basis, without warranty or the implication thereof.
    Neither the Quantum Owners Club nor the individuals associated
    with the Quantum Owners Club or in the preparation of the above
    information shall have any liability to any person or entity with
    respect to liability, loss, or damage caused or alleged to be
    caused directly or indirectly by the instructions contained
    within this or related message(s).
-- You received this message because you are subscribed to the Google
    Groups "Quantum Owners Group" group.
    To post to this group, send email to
    [email protected] <mailto:[email protected]>
    To unsubscribe from this group, send email to
    [email protected]
    <mailto:[email protected]>
    For more options, visit this group at
    http://groups.google.com/group/quantumowners?hl=en

    IMPORTANT NOTE: All information presented herewith is provided on
    an "As Is" basis, without warranty or the implication thereof.
    Neither the Quantum Owners Club nor the individuals associated
    with the Quantum Owners Club or in the preparation of the above
    information shall have any liability to any person or entity with
    respect to liability, loss, or damage caused or alleged to be
    caused directly or indirectly by the instructions contained within
    this or related message(s).


--
You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s).

--
You received this message because you are subscribed to the Google Groups "Quantum 
Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" 
basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor 
the individuals associated with the Quantum Owners Club or in the preparation of the 
above information shall have any liability to any person or entity with respect to 
liability, loss, or damage caused or alleged to be caused directly or indirectly by the 
instructions contained within this or related message(s).

Reply via email to