Is the negative pressure when moving through the air one of the causes? The side windows seem to suffer worst of all, and the windscreen least of all, which could indicate suction created could be the cause. A friend lost a tailgate glass at speed a few years ago, when it just popped out of the rubber.


----- Original Message ----- From: "TonyV" <[email protected]>
To: "Quantum Owners Group" <[email protected]>
Sent: Thursday, March 10, 2011 10:38 AM
Subject: [Quantum Owners] Re: Window adhesive failure


As a refinement of the survey, I'd like to know how many of those
suffering from bonding failure have removed the rear parcel shelf?
Quanum apparently included it as a stiffening panel.
The manual says it can be removed, but might cause extra flexing.



Count me in as one of those suffering from window bonding failure,
even though the parcel shelf is still in place.
Both rear/side and rear screens need re-fitting.

I re-did both rear side windows about 3 years ago, using one a window
bonding kits from ebay designed for fitting van screens.
It didn't look bad when first done, but voids started appearing very
quickly.
All instructions followed, glass scrupulously clean, supplied primers
used, correct amount applied as determined by the included tool, etc.

But the car has been stood still for 2 out of the intervening 3 years,
and the voids have continued to get worse - to the point where algae
is now growing between the adhesive and glass.
So it's more than just flexure of the shell causing the problems.


Here's another suggestion.
The car doors used to be quite difficult to close, due to air pressure
inside the car.  Not a problem with the windows open.
And it's not a problem any more.  The reason is that the rear window
now lifts slightly and allows the extra pressure to escape!
Which is a bit alarming...  But I do wonder if this might have
something to do with the initial separation of the windows.
So, an extra hidden vent might be a benefit.

Obviously, once a void is established which can get water into it,
freeze/thaw will expand the void with each cycle.



I now have my own sand blaster, so will probably try using that on the
glass to give a primed finish this time around.
Once done, I'll also probably have them professionally fitted (need
new rear screen glass anyway due to a few broken elements in the
demister).

And one other refinement - the side windows currently have a slight
gap around the glass, which provides a void which will allow water to
become trapped.
I might well fill this gap with silicone, to keep water out and also
increase the amount of bonding area available.

Tony Vincent.







On Mar 10, 12:58 am, [email protected] wrote:
In a message dated 09/03/2011 20:54:10 GMT Standard Time,

[email protected] writes:

The reason for the rear glass un-glueing is due to flexure in the
bodyshellat at the rear.

It would be interesting to do a check - maybe via the magazine or at the
Stoneleigh meeting

--
You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s).


-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1204 / Virus Database: 1497/3494 - Release Date: 03/09/11


--
You received this message because you are subscribed to the Google Groups "Quantum 
Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" 
basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor 
the individuals associated with the Quantum Owners Club or in the preparation of the 
above information shall have any liability to any person or entity with respect to 
liability, loss, or damage caused or alleged to be caused directly or indirectly by the 
instructions contained within this or related message(s).

Reply via email to