Maybe a 'better' clip than a P clip - I found some useful ones (as used on
Ford Fiesta 99) which held my brake pipes and fuel lies in one
bundle.......TRW Automotive have good selection - can be secured with a
self-tapper in some cases, or a sealed 6mm screw from the other side of a
panel.
Martin
----- Original Message -----
From: "jin" <[email protected]>
To: "Quantum Owners Group" <[email protected]>
Sent: Friday, December 30, 2011 2:40 PM
Subject: [Quantum Owners] bulkhead refurb update
update
ive removed the pop rivets and P clips that held the brake pipes on,
http://i120.photobucket.com/albums/o192/jindal/DSC02331.jpg
they didn't fit too well and the pop rivets didn't go through the
bulkhead so only served to swell out the fiberglass and let water and
dirt in, evidenced by the dirt that had crept within the hole around
the rivet, i chamferd the holes to remove the contaminated fiberglass
and gelcoted from the outside with a thin layer
http://i120.photobucket.com/albums/o192/jindal/DSC02333.jpg
then filled the rear with slow set araldite to seal the join and
hopefully put a bit more strength back in
http://i120.photobucket.com/albums/o192/jindal/DSC02336.jpg
the tape is just to stop it running out and keep it smooth
cut out the first hole for my cable glands, i found a cone step drill
very handy for enlarging holes (I'm using one of my extra? servo mount
holes that were drilled but unused?) since they locate and don't
wander about ripping the gel coat like normal twist drills, only thing
to do is drill both sides sins the steps are shallow,
http://i120.photobucket.com/albums/o192/jindal/DSC02332.jpg
tapped it out to the right size
and sealed the fiberglass with araldite resin and wound the gland in
http://i120.photobucket.com/albums/o192/jindal/DSC02335.jpg
then gave a wipe round the inside with more resin just to be sure,
these should be very water proof now, this one will be for the wiper
motor
as for the brake pipes, I'm not too sure how I'm going to secure the P
clips, I'm not going to use pop rivets fore sure, i may drill a few
holes and tap a thread then wind in a stainless stud with araldite to
seal unless anyone knows a batter way?
cheers for any info
--
You received this message because you are subscribed to the Google Groups
"Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to
[email protected]
For more options, visit this group at
http://groups.google.com/group/quantumowners?hl=en
IMPORTANT NOTE: All information presented herewith is provided on an "As Is"
basis, without warranty or the implication thereof. Neither the Quantum
Owners Club nor the individuals associated with the Quantum Owners Club or
in the preparation of the above information shall have any liability to any
person or entity with respect to liability, loss, or damage caused or
alleged to be caused directly or indirectly by the instructions contained
within this or related message(s).
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1416 / Virus Database: 2109/4111 - Release Date: 12/29/11
--
You received this message because you are subscribed to the Google Groups "Quantum
Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to
[email protected]
For more options, visit this group at
http://groups.google.com/group/quantumowners?hl=en
IMPORTANT NOTE: All information presented herewith is provided on an "As Is"
basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor
the individuals associated with the Quantum Owners Club or in the preparation of the
above information shall have any liability to any person or entity with respect to
liability, loss, or damage caused or alleged to be caused directly or indirectly by the
instructions contained within this or related message(s).
