If I understand what you are asking, pin one of each board is ground on here. There is a ground wire on the power connector that is connected to ground. Is this what you are referring to.
Mathew ----- Original Message ----- From: "Neil McKie" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Friday, June 11, 2004 8:16 PM Subject: Re: [Repeater-Builder] Micor 4 Channel Help Needed > > You may want to determine if the Channel Element frequency select > wire (one of the pins on the bottom) is properly grounded. > > Look at the bottom of the circuit board immediately below the > Channel Element and locate the one connection that goes to the edge > connector P-902 on the Exciter and P-904 on the Receiver. > > See that the one wire is grounded. > > Neil > > Mathew Quaife wrote: > > > > Xtal cases seem to be intact, was told they xtals were still in > > there. Even so, I get no power output, and it does not even > > register a frequency on my freq counter. So no output, and no > > input. There is one extra plug at the control head, and a purple > > wire with a connector on it. > > > > Mathew > > > > ----- Original Message ----- > > From: "N9WYS" <[EMAIL PROTECTED]> > > To: <[email protected]> > > Sent: Friday, June 11, 2004 5:02 PM > > Subject: RE: [Repeater-Builder] Micor 4 Channel Help Needed > > > > > I have seen where elements are sent out for re-crystalling (different > > > freq) and come back with a stick-on label showing the new freq. Maybe > > > the labels came off, revealing a freq that is no longer in the element? > > > (I've actually had this happen to me before.) > > > > > > Mark - N9WYS > > > > > > -----Original Message----- > > > From: Neil McKie [mailto:[EMAIL PROTECTED] > > > Sent: Friday, June 11, 2004 2:30 PM > > > To: [email protected] > > > Subject: Re: [Repeater-Builder] Micor 4 Channel Help Needed > > > > > > > > > Perhaps ... > > > > > > 1) the Channel Elements are on a frequency that the radio is not > > > tuned to or ... > > > > > > 2) there are no crystals in those Channel Elements ... > > > > > > 3) the ground return for the Channel Elements selector switch in > > > the control head is not connected to ground - anywhere. > > > > > > Neil > > > > > > > > > Mathew Quaife wrote: > > > > > > > > Yes, they are in the 163 Mhz range. When I press the mic button > > > > the radio keys up, just no power output. > > > > > > > > Mathew > > > > > > > > ----- Original Message ----- > > > > From: "Neil McKie" <[EMAIL PROTECTED]> > > > > To: <[email protected]> > > > > Sent: Friday, June 11, 2004 10:44 AM > > > > Subject: Re: [Repeater-Builder] Micor 4 Channel Help Needed > > > > > > > > > > > > > > Are there any Channel Elements in it? > > > > > > > > > > Neil > > > > > > > > > > w9mwq wrote: > > > > > > > > > > > > I just got a 4 channel micor radio, T73RTN3180B radio, actually > > > two > > > > > > radio's and one set on control heads. The radio comes on, has > > > good > > > > > > volume, and squelch works, but there is no receiver sensitivity, > > > nor > > > > > > power ouput. Both radios do the exact same thing. I'm thinking > > > > > > control head, but everything seems to be hooked up. > > > > > > > > > > > > Mathew > > > > > > > > > > > > > > > > > > > > > > > > > > > Yahoo! Groups Links > > > > > > > > > > > > > > > > > > > > > Yahoo! Groups Links > > > > > > > > > > > > > > > Yahoo! Groups Links > > > > > Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/
