fully regulated 12vdc power supply ! ----- Original Message ----- From: "Kevin King" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Thursday, February 24, 2005 9:19 PM Subject: RE: [Repeater-Builder] Re: Comm Spec TP-38
> > How are you powering the unit? > > Kevin King SCSA BSCIS > ARS KC6OVD > GMRS KAG0378 > EIEIO 2722 > Acworth Georgia > > > -----Original Message----- > From: Brent [mailto:[EMAIL PROTECTED] > Sent: Tuesday, February 22, 2005 7:45 AM > To: [email protected] > Subject: Re: [Repeater-Builder] Re: Comm Spec TP-38 > > > > Hello Skipp, > > I have all known tones turned on and active..(double checked that a few > times) > It will not decode them or show them at all > it will show and decode all below 100.0 with no problem, and it does that > like it should with no delay.. > > but if i try the 100.0 it has to have that tone signal present for at least > 3 seconds before it will show or decode it.. > > it is like a audio amp gone bad or some thing.. but i did swap them around > and reset the x2122 in the unit and still no difference.. > I must be missing some type of failure somewhere.. > Brent > > > ----- Original Message ----- > From: "skipp025" <[EMAIL PROTECTED]> > To: <[email protected]> > Sent: Tuesday, February 22, 2005 12:48 PM > Subject: [Repeater-Builder] Re: Comm Spec TP-38 > > > > > > > > Does the tone panel even display frequencies above > > 100Hz, just not decode them? That's a software > > problem or programing. Most other problems are > > hardware related. Just running a test sub tone in > > from an external source will tell you mucho. > > > > skipp > > > > > "Brent" <[EMAIL PROTECTED]> wrote: > > > Question... > > > > > > Has anybody had a problem with the Communications Specialists TP-38 > > Tone > > > Panel not decoding PL tones about 100.0hz > > > it decodes from below 100.0 just fine and 100.0 but 100.0 is little > > slow > > > decoding but above 100.0 it just does nothing.. > > > > > > Thanks > > > Brent > > > > > > > > > > > > > > > > > > > > > > > > > > > -- > > > No virus found in this outgoing message. > > > Checked by AVG Anti-Virus. > > > Version: 7.0.300 / Virus Database: 266.2.0 - Release Date: 2/21/2005 > > > > > > --- > > > [This E-mail scanned for viruses at TNWEB LLC] > > > > > > > > > > > > > > > > > > Yahoo! Groups Links > > > > > > > > > > > > > > > > --- > > [This E-mail scanned for viruses at TNWEB LLC] > > > > > > > > > > -- > > No virus found in this incoming message. > > Checked by AVG Anti-Virus. > > Version: 7.0.300 / Virus Database: 266.2.0 - Release Date: 2/21/2005 > > > > > > > > -- > No virus found in this outgoing message. > Checked by AVG Anti-Virus. > Version: 7.0.300 / Virus Database: 266.2.0 - Release Date: 2/21/2005 > > --- > [This E-mail scanned for viruses at TNWEB LLC] > > > > > > > Yahoo! Groups Links > > > > > > > > > > > > > > > Yahoo! Groups Links > > > > > > > > --- > [This E-mail scanned for viruses at TNWEB LLC] > > > > > -- > No virus found in this incoming message. > Checked by AVG Anti-Virus. > Version: 7.0.300 / Virus Database: 266.4.0 - Release Date: 2/22/2005 > > -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.300 / Virus Database: 266.4.0 - Release Date: 2/22/2005 --- [This E-mail scanned for viruses at TNWEB LLC] Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/
