Skipp,

Sounds as if you are talking more of the Micor line rather than the Mitrek.  
MSR2000 is based on Mitrek.  The Mitrek was spec'd from 136-146 and 146-174, 
two ranges.  I wanted to know if the MSR2000 did the same.

Looks as if you get either it will work in 144-148, hi.

The low band version also did the same with Mitrek, 2 bands rather than 3.  Had 
console on 138 that would go to 6 meters.

I have done the helical mod on the Micors with replacing the screw tuning rods 
and worked well...well tuned, but not sure of what the helical is really doing.

73, ron, n9ee/r



>From: skipp025 <[EMAIL PROTECTED]>
>Date: 2007/11/07 Wed AM 11:02:16 CST
>To: [email protected]
>Subject: [Repeater-Builder] Re: MSR2000 info VHF Range Versions

>                  
>Along a generic theme... you can assume there are three VHF Band 
>segements for operation in the 138-174 range. The low split receiver 
>is good from 138 to about 152/155 MHz (working from memory). The 
>second range is about the 149 to 161 MHz range although not stated 
>as this value in the manual.  The third is the high range receiver 
>from about 160 to 174 MHz. 
>
>Both the mid and low range receivers should tune into the 2-Meter 
>Amateur Bands no problama. I'm running a number of mid range boards 
>at 145.310 with great results.  
>
>Most of the issue with the receiver board is the front-end 
>pre-selector assembly follow by the oscillator (channel element) 
>injection chain range (per receiver range model/version) 
>
>Only the high range 160-174 range receiver is not a practical 
>animal for Amateur 2-Meter Band operation.  However, it can be 
>converted up to the 224 Amateur Band if you have the time and 
>tools to "do it right". 
>
>The transmitter board is pretty broad banded and relative to 
>the 138-174 band one board should operate through the entire 
>range. 
>
>There are versions of both the receiver and transmitter board 
>specified for duplex and standard simplex operation. The duplex and 
>high rf version boards have additional connector filtering at the 
>edge pins/plug.
>
>I have tried and use both the duplex and base station (simplex) 
>boards in repeater applications without a problem. 
>
>Like everything... (as seen on ebay and the flea markets) the price 
>of surplus MSR-2000 repeater and base station units are starting to 
>drop to a very practical value. You need only ensure you have a 
>duplex version with a working RF PA and a receiver you can range 
>into your desired band to rock and roll. All the rest is standard 
>Motorhead (Motorola) Repeater 101. 
>
>cheers, 
>skipp 
>
>> Ron Wright <[EMAIL PROTECTED]> wrote:
>> Steve,
>> 
>> Thanks that gave me most of what I needed.  Only thing the 3 in 
>> C73 says VHF, but not the band segment.  Guess not part of this 
>> part number.  Still was very good info.
>> 
>> 73, ron, n9ee/r
>> 
>> 
>> 
>> >From: "Steve S. Bosshard (NU5D)" <[EMAIL PROTECTED]>
>> >Date: 2007/11/06 Tue PM 05:52:32 CST
>> >To: [email protected]
>> >Subject: Re: [Repeater-Builder] MSR2000 info
>> 
>> >                  
>> >http://www.batlabs.com/models.html
>> >
>> >Jim wrote:
>> >> Ron Wright, Skywarn Coodinator wrote:
>> >>   
>> >>> hi all,
>> >>>
>> >>> Anyone know details of a MSR2000 with part number C73GSB-3145B.
>> >>>     
>> >>
>> >
>> >-- 
>> >/Subscribe to dstar_digital/
>> >    
>> >Powered by groups.yahoo.com
><http://groups.yahoo.com/group/dstar_digital>
>> >
>> >            
>> 
>> 
>> Ron Wright, N9EE
>> 727-376-6575
>> MICRO COMPUTER CONCEPTS
>> Owner 146.64 repeater Tampa Bay, FL
>> No tone, all are welcome.
>>
>
>            


Ron Wright, N9EE
727-376-6575
MICRO COMPUTER CONCEPTS
Owner 146.64 repeater Tampa Bay, FL
No tone, all are welcome.


Reply via email to