Luke S Crawford wrote:
carlopmart <[EMAIL PROTECTED]> writes:
When I try to copy a 465MB's or 650MB's file to domU, md5sum is
ok. But when I try to copy a 1GB file or more, md5sums are
wrong. Same result if I try to copy from domU. for example:
...
Please any hints?? I need to deploy this system on a production
environment with xen or with vmware server ...
I can't reproduce the problem; several things to check:
1. ram. your problem could be caused by funky ram. run memtest86.
2. funky swap. run dmesg in the dom0. do you see funky problems related
to disk? run smartctl and see if your disks are dying.
Of course both of those things should also cause periodic swaps, but especially
if you don't use ECC ram, and you normally use less ram than you are using
with virtualization, setting up virtualization could cause to to use funky ram
that would otherwise be idle.
another thing to look at is dmesg in the DomU and see if there are
any interesting messages.
Also, The md5sum is wrong,but is the file size about right?
Thanks Luke for your responses. My answers:
1) memtest86 doesn't reports any error with ram.
2) when I try to start smartd i see these errors:
SCSI device sda: drive cache: write back
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 0
res 51/04:00:80:00:00/00:00:00:00:00/00 Emask 0x1 (device error)
ata1.00: Host Protected Area detected:
current size: 312579695 sectors
native size: 312581808 sectors
ata1.00: Host Protected Area detected:
current size: 312579695 sectors
native size: 312581808 sectors
ata1.00: configured for UDMA/133
ata1: EH complete
3) file size are ok, only md5sums are wrong. But If I try to execute,
decompress, mount or I will try another operation to any file, all fails ...
I have attached dmesg from dom0 and domU
--
CL Martinez
carlopmart {at} gmail {d0t} com
Bootdata ok (command line is ro root=/dev/xvmvol/rootvol quiet)
Linux version 2.6.18-53.1.14.el5xen ([EMAIL PROTECTED]) (gcc version 4.1.2
20070626 (Red Hat 4.1.2-14)) #1 SMP Tue Feb 19 07:33:17 EST 2008
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 00000000b4fe0000 (usable)
On node 0 totalpages: 741344
DMA zone: 741344 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 MSTEST ) @ 0x00000000000f6cd0
ACPI: RSDT (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @
0x00000000bfff3040
ACPI: FADT (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @
0x00000000bfff30c0
ACPI: SLIC (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @
0x00000000bfff77c0
ACPI: MCFG (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @
0x00000000bfff7980
ACPI: MADT (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @
0x00000000bfff76c0
ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20040311) @
0x00000000bfff7a00
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20040311) @
0x00000000bfff7e90
ACPI: DSDT (v001 MSTEST AWRDACPI 0x00001000 MSFT 0x0100000c) @
0x0000000000000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to xen
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
Built 1 zonelists. Total pages: 741344
Kernel command line: ro root=/dev/xvmvol/rootvol quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Xen reported: 3213.968 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Software IO TLB enabled:
Aperture: 64 megabytes
Kernel range: 0xffff880004d0c000 - 0xffff880008d0c000
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Memory: 2819072k/2965376k available (2358k kernel code, 137484k reserved, 1325k
data, 172k init)
Calibrating delay using timer specific routine.. 8039.58 BogoMIPS (lpj=16079170)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
(SMP-)alternatives turned off
ACPI: Core revision 20060707
Brought up 2 CPUs
sizeof(vma)=168 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=240 bytes
Initializing CPU#1
migration_cost=1780
checking if image is initramfs... it is
Grant table initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:12.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
xen_mem: Initialising balloon driver.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:01: ioport range 0x1400-0x147f could not be reserved
pnp: 00:01: ioport range 0x1480-0x14ff has been reserved
pnp: 00:01: ioport range 0x1800-0x187f has been reserved
pnp: 00:01: ioport range 0x1880-0x18ff could not be reserved
pnp: 00:01: ioport range 0x1c00-0x1c7f has been reserved
pnp: 00:01: ioport range 0x1c80-0x1cff has been reserved
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: d0000000-d2ffffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:12.0
IO window: b000-bfff
MEM window: d3000000-d4ffffff
PREFETCH window: d5100000-d51fffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:12.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1208337416.272:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key E192A392652F9718
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist]
[20060707]
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not
present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not
present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Xen virtual console successfully installed as ttyS0
Event-channel device installed.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP04: IDE controller at PCI slot 0000:00:0f.0
NFORCE-MCP04: chipset revision 242
NFORCE-MCP04: not 100% native mode: will probe irqs later
NFORCE-MCP04: 0000:00:0f.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: SONY DVD-ROM DDU1615, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Write protecting the kernel read-only data: 445k
input: AT Translated Set 2 keyboard as /class/input/input0
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
GSI 16 sharing vector 0xA8 and IRQ 16
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 23 (level, low) ->
IRQ 16
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: irq 16, io mem 0xd5004000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
GSI 17 sharing vector 0xB0 and IRQ 17
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCG] -> GSI 22 (level, low) ->
IRQ 17
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ohci_hcd 0000:00:0b.1: OHCI Host Controller
ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.1: irq 17, io mem 0xd5000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 5 ports detected
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
GSI 18 sharing vector 0xB8 and IRQ 18
ACPI: PCI Interrupt 0000:00:0b.2[C] -> Link [APCL] -> GSI 21 (level, low) ->
IRQ 18
PCI: Setting latency timer of device 0000:00:0b.2 to 64
ehci_hcd 0000:00:0b.2: EHCI Host Controller
ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:0b.2: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:0b.2
ehci_hcd 0000:00:0b.2: irq 18, io mem 0xd5001000
ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 10 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
sata_nv 0000:00:10.0: version 3.4
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20
GSI 19 sharing vector 0xC0 and IRQ 19
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [APSI] -> GSI 20 (level, low) ->
IRQ 19
sata_nv 0000:00:10.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:10.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xffffc20000026480 ctl 0xffffc200000264a0 bmdma
0x000000000001dc00 irq 19
ata2: SATA max UDMA/133 cmd 0xffffc20000026580 ctl 0xffffc200000265a0 bmdma
0x000000000001dc08 irq 19
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: Host Protected Area detected:
current size: 312579695 sectors
native size: 312581808 sectors
ata1.00: ATA-7: Maxtor 6V160E0, VA111900, max UDMA/133
ata1.00: 312579695 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: Host Protected Area detected:
current size: 312579695 sectors
native size: 312581808 sectors
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
Vendor: ATA Model: Maxtor 6V160E0 Rev: VA11
Type: Direct-Access ANSI SCSI revision: 05
ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised: [EMAIL PROTECTED]
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1208337423.520:2): selinux=0 auid=4294967295
hda: ATAPI 40X DVD-ROM drive, 1725kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x700
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x900
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APCH] -> GSI 23 (level, low) ->
IRQ 16
PCI: Setting latency timer of device 0000:00:0e.0 to 64
forcedeth: using HIGHDMA
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
input: PC Speaker as /class/input/input2
8139too Fast Ethernet driver 0.9.27
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
sd 0:0:0:0: Attached scsi generic sg0 type 0
eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:0e.0
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
GSI 20 sharing vector 0xC8 and IRQ 20
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [APC3] -> GSI 18 (level, low) ->
IRQ 20
eth1: RealTek RTL8139 at 0xffffc2000002a000, 00:80:5a:4a:2b:fc, IRQ 20
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
GSI 21 sharing vector 0xD0 and IRQ 21
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC4] -> GSI 19 (level, low) ->
IRQ 21
eth2: RealTek RTL8139 at 0xffffc20000032000, 00:08:54:4c:55:60, IRQ 21
eth2: Identified 8139 chip type 'RTL-8100B/8139D'
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 3148732k swap on /dev/sda2. Priority:-1 extents:1 across:3148732k
Bridge firewalling registered
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
audit(1208337430.519:3): dev=eth0 prom=256 old_prom=0 auid=4294967295
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
eth1: Promiscuous mode enabled.
device eth1 entered promiscuous mode
audit(1208337430.683:4): dev=eth1 prom=256 old_prom=0 auid=4294967295
eth2: no link during initialization.
device eth2 entered promiscuous mode
audit(1208337430.887:5): dev=eth2 prom=256 old_prom=0 auid=4294967295
xenbr0: port 1(eth0) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 1(eth0) entering forwarding state
xenbr1: port 1(eth1) entering learning state
xenbr1: topology change detected, propagating
xenbr1: port 1(eth1) entering forwarding state
device srvauth_if entered promiscuous mode
audit(1208337453.204:6): dev=srvauth_if prom=256 old_prom=0 auid=4294967295
blkback: ring-ref 8, event-channel 8, protocol 1 (x86_64-abi)
xenbr0: port 2(srvauth_if) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 2(srvauth_if) entering forwarding state
Bootdata ok (command line is ro root=/dev/sysvol/rootvol quiet)
Linux version 2.6.18-53.1.14.el5xen ([EMAIL PROTECTED]) (gcc version 4.1.2
20070626 (Red Hat 4.1.2-14)) #1 SMP Tue Feb 19 07:33:17 EST 2008
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000030800000 (usable)
On node 0 totalpages: 198656
DMA zone: 198656 pages, LIFO batch:31
No mptable found.
Built 1 zonelists. Total pages: 198656
Kernel command line: ro root=/dev/sysvol/rootvol quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Xen reported: 3213.848 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Software IO TLB disabled
Memory: 758016k/794624k available (2358k kernel code, 27692k reserved, 1325k
data, 172k init)
Calibrating delay using timer specific routine.. 8038.96 BogoMIPS (lpj=16077932)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
(SMP-)alternatives turned off
Brought up 1 CPUs
sizeof(vma)=168 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=240 bytes
checking if image is initramfs... it is
Grant table initialized
NET: Registered protocol family 16
ACPI Exception (utmutex-0262): AE_BAD_PARAMETER, Thread DB57A0 could not
acquire Mutex [2] [20060707]
ACPI Exception (utmutex-0262): AE_BAD_PARAMETER, Thread DB57A0 could not
acquire Mutex [2] [20060707]
Brought up 1 CPUs
PCI: setting up Xen PCI frontend stub
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
xen_mem: Initialising balloon driver.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: System does not support PCI
PCI: System does not support PCI
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1208337453.611:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key E192A392652F9718
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
rtc: IRQ 8 is not free.
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Xen virtual console successfully installed as xvc0
Event-channel device installed.
Console: switching to colour frame buffer device 100x37
input: Xen Virtual Keyboard/Mouse as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
XENBUS: Device with no driver: device/vbd/51712
XENBUS: Device with no driver: device/vif/0
Write protecting the kernel read-only data: 445k
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Registering block device major 202
xvda: xvda1 xvda2 xvda3
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised: [EMAIL PROTECTED]
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1208337461.124:2): selinux=0 auid=4294967295
input: PC Speaker as /class/input/input1
Floppy drive(s): fd0 is unknown type 15 (usb?), fd1 is unknown type 15 (usb?)
Failed to obtain physical IRQ 6
floppy0: no floppy controllers found
lp: driver loaded but no devices found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on xvda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1574360k swap on /dev/xvda2. Priority:-1 extents:1 across:1574360k
netfront: Initialising virtual ethernet driver.
netfront: device eth0 has flipping receive path.
_______________________________________________
rhelv5-list mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/rhelv5-list
