Usually, I would expect resource not generated as the first run into the
DB for a new host. As soon as you restart the Rivendell services (or
reboot the machine) the DB will get updated with the audio config info
as soon as caed etc runs.
Worst case scenario, the audio config is just a DB entry in the STATIONS
table. You could copy the line from your working local copy into the
server DB and see if that helps? (Backup your DB first just in case).
On 01/03/16 15:23, Nick Andre wrote:
Yes. I'm wondering if there's something unsupported about this
configuration.
If I create a local database everything generates just fine and my ASI
card is assigned to Card 0 on the local system. When I take the same
exact configuration and point it to the old server/database it doesn't
generate audio resource data. I've double checked that the IP matches
in the remote case (I can't eliminate the possibility I'm being
excessively foolish but I can use rdadmin from the remote computer).
I'd be interested to dig in a bit and see what it's doing and where
it's failing. As a last ditch effort I can also repeat the install
procedure on a new VM and see if anything different happens (would be
good for our documentation as well).
On Tuesday, March 1, 2016, Wayne Merricks
<[email protected]
<mailto:[email protected]>> wrote:
Stupid question, did you add the new host name to rdadmin, is the
IP address correct for the new host?
On 29/02/16 21:09, Nick Andre wrote:
I have one ASI card on the system (Card 0 in the old server).
I've installed an ASI card on this new machine too (and left the
index on the card at the default 1). The rdhpiinfo shows me that
the card appears to be all set. But for some reason it's not
correctly populating the audio resources data on service start.
Has anyone tried to migrate to a new host before? Basically we
want to get both hosts running in parallel each with their own
ASI card and then migrate all playout hosts (that just run
rdairplay) swapped over to the new server.
On Sun, Feb 28, 2016 at 2:09 PM Nick Andre <[email protected]
<javascript:_e(%7B%7D,'cvml','[email protected]');>> wrote:
I'm getting the "audio resource data has not been generated"
error in RDAdmin for a new host (with a Livewire ASI card).
However, restarting doesn't appear to generate that data. I
also don't see the ASI card being detected. Output when I
restart the host:
Feb 27 16:13:11 rivendell rdcatchd: rdcatchd exiting
Feb 27 16:13:11 rivendell ripcd: ripcd exiting normally
Feb 27 16:13:11 rivendell caed: cae exiting
Feb 27 16:13:13 rivendell caed: unable to communicate with
JACK server
Feb 27 16:13:13 rivendell caed: JACK general failure
Feb 27 16:13:13 rivendell caed: no connection to JACK server
Feb 27 16:13:13 rivendell caed: MPEG L2 encoding not enabled
Feb 27 16:13:13 rivendell caed: Found MAD decoder library,
MPEG L2 decoding supported
Feb 27 16:13:13 rivendell caed: using realtime scheduling,
priority=8
Feb 27 16:13:13 rivendell caed: cae started
Feb 27 16:13:15 rivendell ripcd: started
Feb 27 16:13:16 rivendell rdcatchd: rdcatchd engine load
starts...
Feb 27 16:13:16 rivendell rdcatchd: loaded 0 events
Feb 27 16:13:16 rivendell rdcatchd: rdcatchd engine load ends
Feb 27 16:13:16 rivendell rdcatchd: rdcatchd started
_______________________________________________
Rivendell-dev mailing list
[email protected]
<javascript:_e(%7B%7D,'cvml','[email protected]');>
http://caspian.paravelsystems.com/mailman/listinfo/rivendell-dev
_______________________________________________
Rivendell-dev mailing list
[email protected]
http://caspian.paravelsystems.com/mailman/listinfo/rivendell-dev
