Buna,
Am o problema cu o placa SMC 1211 si anume:
~#modprobe 8139too
Sep 4 20:17:15 blank kernel: 8139too Fast Ethernet driver 0.9.18a
Sep 4 20:17:15 blank kernel: PCI: Found IRQ 10 for device 00:0b.0
Sep 4 20:17:15 blank kernel: PCI: Sharing IRQ 10 with 00:07.2
Sep 4 20:17:15 blank kernel: PCI: Sharing IRQ 10 with 00:07.3
Sep 4 20:17:15 blank kernel: Assertion failed! ioaddr !=
NULL,8139too.c,rtl8139_init_one,line=944
Sep 4 20:17:15 blank kernel: eth3: SMC1211TX EZCard 10/100 (RealTek RTL8139)
at 0xc400, ff:ff:ff:ff:ff:ff, IRQ 10
Sep 4 20:17:15 blank kernel: eth3: Identified 8139 chip type 'RTL-8139C'
~#ifup eth3
Sep 4 20:17:15 blank kernel: 8139too Fast Ethernet driver 0.9.18a
Sep 4 20:17:15 blank kernel: PCI: Found IRQ 10 for device 00:0b.0
Sep 4 20:17:15 blank kernel: PCI: Sharing IRQ 10 with 00:07.2
Sep 4 20:17:15 blank kernel: PCI: Sharing IRQ 10 with 00:07.3
Sep 4 20:17:15 blank kernel: Assertion failed! ioaddr !=
NULL,8139too.c,rtl8139_init_one,line=944
Sep 4 20:17:15 blank kernel: eth3: SMC1211TX EZCard 10/100 (RealTek RTL8139)
at 0xc400, ff:ff:ff:ff:ff:ff, IRQ 10
Sep 4 20:17:15 blank kernel: eth3: Identified 8139 chip type 'RTL-8139C'
Sep 4 20:17:42 blank kernel: eth3: Setting 100mbps half-duplex based on
auto-negotiated partner ability ffff.
Sep 4 20:17:42 blank kernel: probable hardware bug: clock timer configuration
lost - probably a VIA686a motherboard.
Sep 4 20:17:42 blank kernel: probable hardware bug: restoring chip
configuration.
Sep 4 20:17:54 blank kernel: NETDEV WATCHDOG: eth3: transmit timed out
Sep 4 20:17:54 blank kernel: eth3: Tx queue start entry 4 dirty entry 0.
Sep 4 20:17:54 blank kernel: eth3: Tx descriptor 0 is ffffffff. (queue head)
Sep 4 20:17:54 blank kernel: eth3: Tx descriptor 1 is ffffffff.
Sep 4 20:17:54 blank kernel: eth3: Tx descriptor 2 is ffffffff.
Sep 4 20:17:54 blank kernel: eth3: Tx descriptor 3 is ffffffff.
Sep 4 20:17:54 blank kernel: eth3: Setting 100mbps half-duplex based on
auto-negotiated partner ability ffff.
Am incercat sa o pun default pe 10 Half Duplex da nimic acelasi lucru. Acelasi
lucru se intimpla si cu Autoproble
Exista cumva alti parametri la modprobe prin care sa ii spun sa mearga la 10
nu la 100 ?
Personal am cautat prin /usr/src/linux/Documentation/* si pe net da nu am
gasit nimic care sa ma ajute.
[M]isu
---
Send e-mail to '[EMAIL PROTECTED]' with 'unsubscribe rlug' to
unsubscribe from this list.
