A mers, merci Aline. Dau berea. Sorin
Alin Nastac wrote: > > Toate wellgate-urile au cam acelasi firmware, asa ca iata procedura: > > 1. te legi pe seriala device-ului > 2. pornesti minicom-ul (9600 8N1 no flow control - doar 3 fire conectate) > 3. pornesti wellgate-ul > 4. la inceput, are o secventa in care daca-i dai enter in primele 3 > secunde intra in boot mode; evident, ii dai enter atunci > 5. iti va cere username-ul si parola: username=water password=3333 > 6. dai p sa-i schimbi parola (aici nu sint sigur; vezi help) > > mai jos ai procedura de upgrade folosind boot mode. astept berea ;) > > Update WG3806 in boot mode Procedures > > Prepare the following before You starting. > - Turn OFF Wellgate 3806 > - Connect console port cable from WG3806 to PC > - Connect WG3806 and PC to an local LAN > - Install tftp program to your PC and activated the tftp program > - Put download file (i.e. 2MWG3806.111) and tftp program at the same > directory in your PC > - Activate HyperTerminal program from your PC > > Now, Turn ON power supply of Wellgate 3806. You will see the following > display from HyperTerminal display of your PC. > > Attached TCP/IP interface to cpm unit 0 > Attaching interface lo0...done > Please wait while system is initializing .......... ----> press > enter within 3 seconds. > > Now it is in BOOT MODE. > > boot line : cpm(0,0)host:vxWorks h=192.168.4.109 e=192.168.201.201 > u=vwusr pw=vw > usr g=192.168.1.254 > > login : water > > password : 3333 > > [help] , list all boot commands > > 1. [c] > <BOOT> c > - Please input your new network address. ----> for example, > - Tftp server addr: 192.168.4.109 ----> prepare one tftp server > - Target addr: 192.168.119.119 ----> given one IP address > for the Wellgate 3806 > - Gateway addr: 192.168.1.254 ----> default network > gateway ip address > - user (u): ----> key in any number > - ftp password (pw): ----> key in any number > - netmask : ----> key in any number > > > - if network address is correct, please press 'y' to > setup configuration, else press 'n' to continue. -----> y > > bootline configuraton OK. > - auto reset > Starting at 0x2800100... > > Attached TCP/IP interface to cpm unit 0 -----> again > Attaching interface lo0...done > Please wait while system is initializing .......... -----> press > enter within 3 seconds. > > Key in Login and password as above. > > Note, all IP Address must be in the same subnet mask and default gateway. > > 2. [f] > > <BOOT> f > - Transfer File Name: 2mwt3806 .111 ----> example , file to be > download > > 3. [d] > > <BOOT> d > - download program. > - Load .... > Tftp transfer OK. > > Note: if it is not successful, try to change another IP Address for > Wellgate 3806 at - Target addr: 192.168.119.119 and repeat step 1 > again. > > 4. [z] > > <BOOT> z > - programming 2M rom file > > - Be sure to program boot sector!!?(y/n):y --------> press y > > Please wait for a moment!!! > - programming OK. > > > 5. [r] > <BOOT> r > - software reset > Starting at 0x2800100... > > After download is finished, all the settings will return to default > values including IP > address (default IP address is 10.1.1.3) and MAC address, so please > re-configure IP address > and MAC address and reboot it. > > Configure the MAC address with the command > > setmac > (Note: Each network device MUST has an unique mac address which are 12 > digits length. The H.323 gateway has to re-configure an unique mac > address after this upgrade procedure. An unproper operation may be > happened if mac address is duplicated with other network device.) > > key in mac address with format: 00 > 01 > a8 > 00 > 0x > xx > (It means to press enter key each time after key in two characters.) > You can find the device MAC address from the label which is located at > the bottom of Wellgate 3806 metal case. Now, give the following two > commands. > > flash -clean > reboot > > Now, you can start to configure your setting on Wellgate 3806. > > Sorin Savastre wrote: > > >Salut, > > > >Am primit de la cineva un WellGate 3502. Din pacate nu isi mai aminteste > >parola de root, pe care a schimbat-o. Default era adresa MAC a > >ethernetului. Cei de la Welltech sunt de o secretomanie nemaiintalnita, > >nu gasesti la ei pe site absolut nimic, decat cu login cu user si > >parola. Oricum, in nici o documentatia de a lor nici macar nu se > >pomeneste ceva de "password recovery", la nici un model. Pe net nu am > >gasit absolut nimic. Vreo idee? Dau o bere. > > > >Sorin > > > >--- > >Detalii despre listele noastre de mail: http://www.lug.ro/ > > > > > > > > > > --- > Detalii despre listele noastre de mail: http://www.lug.ro/ --- Detalii despre listele noastre de mail: http://www.lug.ro/
