I just got this to work on RH7.1:
get linux-2.4.1-tar.gz from ftp.kernel.org.
un-tar it in /usr/src
patch it with kernel_patch-2.4.1-x86
The instructions that you have can be followed from there.
make the link to rtlinux-3.0 in /usr/src/linux
configure it and be sure to turn off power management
compile that kernel: make bzImage, copy bzImage to /boot/rtzImage
fix lilo.conf and run lilo, then reboot to the new 2.4.1 rtlinux kernel
Then, compile the rtlinux stuff, while running the new kernel
you should get a better result.
>Hello!
>
>I have begun installation of rtl 3.0 on a fresh Redhat 7.1 system. I had to
>install ecgs 1.1.2 (via compat-ecgs-6.2-1.1.2.14.rpm) as per installation
>instructions. Unfortunately, I cannot get "rtlinux start" to load the modules
>properly, or at least output something which I believe is sane.
>
>Here is the output:
>-------------
>cd /usr/rtlinux/bin
>./rtlinux start
>RTLinux Extensions Loaded (http://www.fsmlabs.com/)
>
>Scheme: (-) not loaded, (+) loaded
> (-) start
> (-) *
>-----------
>Then things start to go downhill. ls will not return anything, ps and top
>dumps
>core.
>
>I try ./examples/hello", with make test, to no avail. It compiles, but I
>do not
>get any reasonable output.
>
>lsmod lists: rtl_fifo, rtl_posixio, rtl_sched, rtl_time, rtl as loaded.
>---------
>My hardware is striaghtforward:
>intel 740 video
>WD 20 GD HD
>Pentium III 450
>256 MB RAM
>AOpen AX6BC mainboard
>
>Here is what I tried:
>
>The rtl 2.4.0 patched kernel (rtlinux_kernel_2_4.tar.gz) was downloaded and
>uncompressed in /usr/src.
>rtlinux-3.0.tar.gz was uncompressed in /usr/src.
>A symbolic link in /usr/src/rtlinux-3.0/ was made to the kernel source
>directory.
>In /usr/src/rtlinux_kernel_2.4.0-test1-rtl/, the Makefile was changed so
>CC and
>HOSTCC read kgcc.
>make menuconfig was executed, the default configuration was used, and config
>exited. make dep, bzImage, modules, modules_install proceeded.
>the resulting image was copied to root, and lilo executed.
>
>The machine was then rebooted.
>
>In /usr/src/rtlinux-3.0/, make, make devices and install created the rtlinux
>modules, devices and directories.
>
>in ./bin/, rtlinux start was typed at the command line.
>
>The kernel will boot, and even start xdm, but when I try to load the
>
>Thanks for any pointers,
>Mike Seymour
>
>--
>______________________________________________
>
> VPI - EXPERTISE YOU CAN COUNT ON
>_______________________________________________
>
> Michael Seymour
> Vantage Point International Inc.
> 1704 Carling Avenue, 2nd Floor
> Ottawa, Ontario K2A 1C7
> Tel (613) 798-2244, ext 226
> Fax (613) 798-5369
> E-mail: [EMAIL PROTECTED]
> http://www.vantpoint.com
>________________________________________________
>
>
>----- End of forwarded message from [EMAIL PROTECTED] -----
>-- [rtl] ---
>To unsubscribe:
>echo "unsubscribe rtl" | mail [EMAIL PROTECTED] OR
>echo "unsubscribe rtl <Your_email>" | mail [EMAIL PROTECTED]
>--
>For more information on Real-Time Linux see:
>http://www.rtlinux.org/
>
David H. Thompson, 865-574-5633, ORNL, PO Box 2008,Oak Ridge, TN 37831-6426
----- End of forwarded message from [EMAIL PROTECTED] -----
-- [rtl] ---
To unsubscribe:
echo "unsubscribe rtl" | mail [EMAIL PROTECTED] OR
echo "unsubscribe rtl <Your_email>" | mail [EMAIL PROTECTED]
--
For more information on Real-Time Linux see:
http://www.rtlinux.org/
