Pherhaps my thread can help you:HOWTO samba4 centos5.5 named dnsupdate drbd simple failover
A simply make uninstall could help you. But to start samba you need the executables in your PATH!!! On Sun, 27 Feb 2011 11:34:53 +0100, Santiago DIEZ <[email protected]> wrote: > Hi Peter, > > If the install worked fine, then you should be able to run the daemon with: > /usr/local/samba/smbd -- -D > You probably can't call it without the full path because > /usr/local/samba/is not in your path. > > If you want to remove a program compiled from source, go back to the source > directory and run > make uninstallbin > make uninstalldat > make uninstallman > make uninstallmo > make uninstallmsg > make uninstallscripts > make uninstall > > Tell me if this helps > --- > *Santiago DIEZ > Directeur > *+33 6 37 90 81 98 > +33 9 70 44 77 87 > > > > > 2011/2/27 Herczeg Péter <[email protected]> > >> Hi Santiago, >> >> I have tried the follow the HowTo precisely, so I have installed it to: * >> /usr/local/samba* >> By following the instructions (and wanted to run in standard mode) I have >> just typed "samba". >> tried smbd, samba4, but no success. >> >> I did the whole downloading/compiling/installing/provisioning process as >> 'root', I think it has full access for the partition. >> >> To make a very clean install how can I remove everything related to >> samba3 >> or samba4? (during initial setup of Debian installation I have selected >> Samba to install as a feautre) >> I tried to remove with apt-get autoremove, but I got the error message >> that >> samba4 virtual package cannot be removed. >> >> since then, after I reinstalled samba4 followed the HowTo, the >> samba-master >> directory does not appear in my home folder (it was there, when I >> previously >> installed) >> >> If I send you the summary files or process information related to >> compiling/installing/provisioning can help you? >> >> Thanks for your time, >> >> Peter >> 2011. február 27. 11:04 Santiago DIEZ írta, < >> [email protected]>: >> >> Hi Peter, >>> >>> What directory have you installed the binaries to? >>> Are you running the samba command with full path? >>> What command exactly? >>> Have you checked execution privilege on the partition? >>> >>> Bye >>> --- >>> *Santiago DIEZ >>> Directeur >>> *+33 6 37 90 81 98 >>> +33 9 70 44 77 87 >>> >>> >>> >>> >>> 2011/2/27 Herczeg Péter <[email protected]> >>> >>>> Dear All, >>>> >>>> I would like to ask your help: >>>> >>>> I have installed Samba4 by following the steps of Samba4 Wiki Howto to >>>> a >>>> Debian Server. >>>> >>>> - downloaded via git >>>> - compiled successfully >>>> - make quicktest is ok. (as far as I see during the process, it has >>>> written >>>> at the ned: ALL OK) >>>> - install is successful ('install' finished successfully) >>>> - DC provision is successful (get the summary windows at the end, only >>>> notice is to configure phpLDAPadmin) >>>> >>>> And the problem is: >>>> >>>> going to the next step, I try to start&test, but I get the error >>>> message >>>> when executing samba command: >>>> "command not found" >>>> >>>> tried to start as service but no success. >>>> if I used the install path in the same way as it written in the HowTo, >>>> how >>>> can I check is it running and is able to manage the domain? >>>> >>>> Thanks in advance, >>>> >>>> Peter >>>> -- >>>> To unsubscribe from this list go to the following URL and read the >>>> instructions: https://lists.samba.org/mailman/options/samba >>>> >>> >>> >> >> >> -- >> Herczeg Péter >> -- To unsubscribe from this list go to the following URL and read the instructions: https://lists.samba.org/mailman/options/samba
