greetings, I've recently tried my HP ScanJet 5p scanner, that is attached to my PC through an Initio-9100uw scsi interface. After recompiled
uuu $ uname -a FreeBSD uuu.pmi 4.6.2-RELEASE-p4 FreeBSD 4.6.2-RELEASE-p4 #3: Wed Nov 13 08:23:20 CET 2002 [email protected]:/usr/src/sys/compile/UUU i386 kernel, my machine found: uuu $ dmesg | grep Ini iha0: <Initio INI-9XXXU/UW PCI SCSI adapter> port 0xac00-0xacff mem 0xdfeff000-0xdfefffff irq 10 at device 9.0 on pci2 and uuu $ dmesg | grep pass0 pass0 at iha0 bus 0 target 2 lun 0 pass0: <HP C5110A 3701> Fixed Processor SCSI-2 device pass0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit) so I though everything will work well, since my scanner is shown as supported model on http://www.mostang.com/sane/sane-mfgs.html#HEWLETT-PACKARD I've installed sane-backends-1.0.8 from ports, did: uuu $ sane-find-scanner found SCSI processor "HP C5110A 3701" at /dev/scanner found SCSI processor "HP C5110A 3701" at /dev/pass0 [...] uuu $ export SANE_DEBUG_HP=128; scanimage -L [sanei_debug] Setting debug level of hp to 128. [hp] sane_init called [hp] sane_init will finish with Success [hp] sane_get_devices called [hp] hp_read_config: hp backend v0.96 starts reading config file [hp] hp_read_config: processing line <scsi HP> [hp] hp_read_config: processing line </dev/scanner> [hp] hp_read_config: attach scsi HP [hp] hp_get_dev: New device /dev/pass0, connect-scsi, scsi-request=1 [hp] sanei_hp_device_new: /dev/pass0 [hp] scsi_inquire: sending INQUIRE [hp] scsi_new: sending TEST_UNIT_READY [hp] scsi_flush: writing 2 bytes: [hp] 0x0000 1B 45 .E [hp] scsi_flush: writing 7 bytes: [hp] 0x0000 1B 2A 73 32 35 37 45 .*s257E [hp] scl_inq: read failed (Error during device I/O) [hp] scl_errcheck: Can't read SCL error stack: Error during device I/O [hp] sanei_hp_device_new: SCL reset failed [hp] scsi_close: closing fd 0 [hp] hp_read_config: processing line <option disable-scsi-request> [hp] hp_read_config: processing line <# uncomment this if you're using a usb scanner> [hp] hp_read_config: processing line <# /dev/usb/scanner0> [hp] hp_read_config: processing line <# option connect-device> [hp] hp_read_config: attach /dev/scanner [hp] hp_get_dev: New device /dev/scanner, connect-scsi, scsi-request=0 [hp] sanei_hp_device_new: /dev/scanner [hp] scsi_inquire: sending INQUIRE [hp] scsi_new: sending TEST_UNIT_READY [hp] scsi_flush: writing 2 bytes: [hp] 0x0000 1B 45 .E [hp] scsi_flush: writing 7 bytes: [hp] 0x0000 1B 2A 73 32 35 37 45 .*s257E [hp] scl_inq: read failed (Error during device I/O) [hp] scl_errcheck: Can't read SCL error stack: Error during device I/O [hp] sanei_hp_device_new: SCL reset failed [hp] scsi_close: closing fd 0 [hp] hp_read_config: reset to default config [hp] sane_get_devices will finish with Success No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). [hp] sane_exit called [hp] sane_exit will finish at this point I can't resolve the problem. Has anybody idea about? just for info: I've also tried the newer backend, similar results. the scsi-card works with an external cd-writer unit. Thanks in advance, regards -- tef
