Hi, seems to be a SCSI problem. Opening the SCSI-device is ok. Writing seems also to work. But reading is a problem. You can also have a look at the system log messages. If there are errors reported from the SCSI drivers.
Sincerely Peter SITKEI Attila schrieb: > greetings, > > I've recently tried my HP ScanJet 5p scanner, that is attached to my PC > through an Initio-9100uw scsi interface. After recompiled > > uuu $ uname -a > FreeBSD uuu.pmi 4.6.2-RELEASE-p4 FreeBSD 4.6.2-RELEASE-p4 #3: Wed Nov 13 > 08:23:20 CET 2002 [email protected]:/usr/src/sys/compile/UUU i386 > > kernel, my machine found: > > uuu $ dmesg | grep Ini > iha0: <Initio INI-9XXXU/UW PCI SCSI adapter> port 0xac00-0xacff mem > 0xdfeff000-0xdfefffff irq 10 at device 9.0 on pci2 > > and > > uuu $ dmesg | grep pass0 > pass0 at iha0 bus 0 target 2 lun 0 > pass0: <HP C5110A 3701> Fixed Processor SCSI-2 device > pass0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit) > > so I though everything will work well, since my scanner is shown as > supported > model on > http://www.mostang.com/sane/sane-mfgs.html#HEWLETT-PACKARD > > I've installed sane-backends-1.0.8 from ports, did: > > > uuu $ sane-find-scanner > > found SCSI processor "HP C5110A 3701" at /dev/scanner > found SCSI processor "HP C5110A 3701" at /dev/pass0 > [...] > > uuu $ export SANE_DEBUG_HP=128; scanimage -L > [sanei_debug] Setting debug level of hp to 128. > [hp] sane_init called > [hp] sane_init will finish with Success > [hp] sane_get_devices called > [hp] hp_read_config: hp backend v0.96 starts reading config file > [hp] hp_read_config: processing line <scsi HP> > [hp] hp_read_config: processing line </dev/scanner> > [hp] hp_read_config: attach scsi HP > [hp] hp_get_dev: New device /dev/pass0, connect-scsi, scsi-request=1 > [hp] sanei_hp_device_new: /dev/pass0 > [hp] scsi_inquire: sending INQUIRE > [hp] scsi_new: sending TEST_UNIT_READY > [hp] scsi_flush: writing 2 bytes: > [hp] 0x0000 1B 45 .E > [hp] scsi_flush: writing 7 bytes: > [hp] 0x0000 1B 2A 73 32 35 37 45 .*s257E > [hp] scl_inq: read failed (Error during device I/O) > [hp] scl_errcheck: Can't read SCL error stack: Error during device I/O > [hp] sanei_hp_device_new: SCL reset failed > [hp] scsi_close: closing fd 0 > [hp] hp_read_config: processing line <option disable-scsi-request> > [hp] hp_read_config: processing line <# uncomment this if you're using a usb > scanner> > [hp] hp_read_config: processing line <# /dev/usb/scanner0> > [hp] hp_read_config: processing line <# option connect-device> > [hp] hp_read_config: attach /dev/scanner > [hp] hp_get_dev: New device /dev/scanner, connect-scsi, scsi-request=0 > [hp] sanei_hp_device_new: /dev/scanner > [hp] scsi_inquire: sending INQUIRE > [hp] scsi_new: sending TEST_UNIT_READY > [hp] scsi_flush: writing 2 bytes: > [hp] 0x0000 1B 45 .E > [hp] scsi_flush: writing 7 bytes: > [hp] 0x0000 1B 2A 73 32 35 37 45 .*s257E > [hp] scl_inq: read failed (Error during device I/O) > [hp] scl_errcheck: Can't read SCL error stack: Error during device I/O > [hp] sanei_hp_device_new: SCL reset failed > [hp] scsi_close: closing fd 0 > [hp] hp_read_config: reset to default config > [hp] sane_get_devices will finish with Success > > No scanners were identified. If you were expecting something different, > check that the scanner is plugged in, turned on and detected by the > sane-find-scanner tool (if appropriate). Please read the documentation > which came with this software (README, FAQ, manpages). > [hp] sane_exit called > [hp] sane_exit will finish > > > at this point I can't resolve the problem. Has anybody idea about? > just for info: I've also tried the newer backend, similar results. the > scsi-card works with an external cd-writer unit. > > > Thanks in advance, regards > > > > -- tef > _______________________________________________ > Sane-devel mailing list > [email protected] > http://www.mostang.com/mailman/listinfo/sane-devel > -- Peter Kirchgessner http://www.kirchgessner.net mailto:[email protected]
