Could you send the results of the compiler when you add --verbose option?
sdcc --use-non-free -mpic14 -ppic16f1829 tst.c --verbose
2016-03-03 11:27 GMT+01:00 Jaromir Sukuba <jarin...@gmail.com>:
> I started new clean virtual machine with 32-bit Linux Mint 17.3, ran
> all updates and then:
>
> 1, Installed gputils from source:
> # svn co https://gputils.svn.sourceforge.net/svnroot/gputils/trunk/gputils
> gputils_svn
> ----listing cut short----
> - Checked out revision 1195.
> Then ran configure and make install as expected.
> # gpasm -v
> gpasm-1.4.2 #1194 (Mar 2 2016)
>
> 2, Installed SDCC from source
> downloaded last shapshot "sdcc-src-20160302-9509.tar.bz2" and ran
> # sudo apt-get install libboost-all-dev g++ texinfo
> then ran configure, make, make install as expected
> # sdcc -v
> SDCC :
> mcs51/z80/z180/r2k/r3ka/gbz80/tlcs90/ds390/pic16/pic14/TININative/ds400/hc08/s08/stm8
> 3.5.5 #9509 (Linux)
> published under GNU General Public License (GPL)
>
> 3, Created new file tst.c containing
> void main (void)
> {
> while (1);
> }
>
> 4, Ran compilation for 16F877
> # sdcc --use-non-free -mpic14 -ppic16f877 tst.c
> message: Using default linker script
> "/usr/local/share/gputils/lkr/16f877_g.lkr".
> and produces valid output
>
> 5, Ran compilation for 16F1829
> # sdcc --use-non-free -mpic14 -ppic16f1829 tst.c
> message: Using default linker script
> "/usr/local/share/gputils/lkr/16f1829_g.lkr".
> error: Processor family mismatch in "idata.o".
> only tst.asm and tst.o are produced, no st or hex file, assuming
> because of failed link step
>
> Seems like other PIC16F1xxx MCUs are affected too, PIC16Fxxx are OK.
>
> By the way, I installed SDCC from source, because it is linked against
> GLIBC 3.4.20, emitting the "version `GLIBCXX_3.4.20' not found
> (required by ./sdcc)" message when running sdcc binaries, so running
> it on 32-bit Linux Mint 17.3 out of the box is not possible.
> On the other hand, on 64-bit Linux Mint 17.2 (running on real
> hardware) there isn't GLIBC problem, just the "idata.o" problem.
>
>
>
>
>
>
> 2016-03-01 23:54 GMT+01:00 Gál Zsolt <tralitove...@freemail.hu>:
> > Hello,
> >
> > Here is the test result again:
> >
> > sdcc --use-non-free -mpic14 -ppic16f877 tst.c
> > message: Using default linker script
> > "/usr/local/share/gputils/lkr/16f877_g.lkr".
> >
> > sdcc --use-non-free -mpic14 -ppic16f1829 tst.c
> > message: Using default linker script
> > "/usr/local/share/gputils/lkr/16f1829_g.lkr".
> >
> > sdcc -v
> > SDCC : pic14 3.5.5 #9509 (Linux)
> > published under GNU General Public License (GPL)
> >
> > gpasm -v
> > gpasm-1.4.2 #1186 (Feb 17 2016)
> >
> > What is the version number of your gputils?
> >
> > Regards,
> >
> > Zsolt Gál
> >
> >
> >
> > 2016-02-29 14:55 GMT+01:00 Jaromir Sukuba <jarin...@gmail.com>:
> >>
> >> Hello,
> >> this is my first post in here.
> >>
> >> I'm using SDCC to build project with PIC16F1829. It worked on two
> >> machines - one Linux box with SDCC snapshot 3.5.1 #9263, second one is
> >> windows machine with SDCC 3.5.4 #9360. I always used the latest
> >> snapshot. For Linux 3.5.0 build I have problem running the binary, due
> >> to the "GLIBC 3.4.20" problem. I'm trying to build the same project on
> >> third machine, with newest snapshot 3.5.5 #9509, but I'm running into
> >> problems.
> >> I isolated the problem to simplest source:
> >>
> >> When compiling simple source (tst.c) for PIC16F877
> >> # sdcc --use-non-free -mpic14 -ppic16f877 tst.c
> >> message: Using default linker script
> >> "/usr/local/share/gputils/lkr/16f877_g.lkr".
> >> #
> >>
> >> though the same on PIC16F1829
> >> # sdcc --use-non-free -mpic14 -ppic16f1829 tst.c
> >> message: Using default linker script
> >> "/usr/local/share/gputils/lkr/16f1829_g.lkr".
> >> error: Processor family mismatch in "idata.o".
> >> #
> >>
> >> where tst.c looks like:
> >> void main (void)
> >> {
> >> while (1);
> >> }
> >>
> >> For PIC16F877, there is normally generated code - for PIC16F1829,
> nothing.
> >> I tried to google for this error and this one looks similar
> >> https://sourceforge.net/p/sdcc/mailman/message/34324501/ though the
> >> changes that Gál Zsolt suggested seem to be in pic14device.txt file as
> >> expected:
> >>
> >> processor 16f1829, 16lf1829
> >> program 8K
> >> data 1024
> >> eeprom 256
> >> enhanced 1
> >> io 18
> >> maxram 0x07f
> >> bankmsk 0xf80
> >> config 0x8007 0x8008
> >> regmap 0xf80 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07
> >> 0x08 0x09 0x0a 0x0b
> >> memmap 0x20 0x6f 0x000
> >> memmap 0x70 0x7f 0xf80
> >>
> >>
> >> Any idea what is the problem with my setup? Any additional info I can
> >> provide?
> >>
> >> Thanks,
> >> Jaromir Sukuba
> >>
> >>
> >>
> ------------------------------------------------------------------------------
> >> Site24x7 APM Insight: Get Deep Visibility into Application Performance
> >> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
> >> Monitor end-to-end web transactions and take corrective actions now
> >> Troubleshoot faster and improve end-user experience. Signup Now!
> >> http://pubads.g.doubleclick.net/gampad/clk?id=272487151&iu=/4140
> >> _______________________________________________
> >> Sdcc-user mailing list
> >> Sdcc-user@lists.sourceforge.net
> >> https://lists.sourceforge.net/lists/listinfo/sdcc-user
> >
> >
> >
> >
> > --
> > ~~~~~~~~~~~~~~~~
> > http://galzsolt.zzl.org
> >
> >
> ------------------------------------------------------------------------------
> > Site24x7 APM Insight: Get Deep Visibility into Application Performance
> > APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
> > Monitor end-to-end web transactions and take corrective actions now
> > Troubleshoot faster and improve end-user experience. Signup Now!
> > http://pubads.g.doubleclick.net/gampad/clk?id=272487151&iu=/4140
> > _______________________________________________
> > Sdcc-user mailing list
> > Sdcc-user@lists.sourceforge.net
> > https://lists.sourceforge.net/lists/listinfo/sdcc-user
> >
>
>
> ------------------------------------------------------------------------------
> Site24x7 APM Insight: Get Deep Visibility into Application Performance
> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
> Monitor end-to-end web transactions and take corrective actions now
> Troubleshoot faster and improve end-user experience. Signup Now!
> http://pubads.g.doubleclick.net/gampad/clk?id=272487151&iu=/4140
> _______________________________________________
> Sdcc-user mailing list
> Sdcc-user@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/sdcc-user
>
--
~~~~~~~~~~~~~~~~
http://galzsolt.zzl.org
------------------------------------------------------------------------------
Site24x7 APM Insight: Get Deep Visibility into Application Performance
APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
Monitor end-to-end web transactions and take corrective actions now
Troubleshoot faster and improve end-user experience. Signup Now!
http://pubads.g.doubleclick.net/gampad/clk?id=272487151&iu=/4140
_______________________________________________
Sdcc-user mailing list
Sdcc-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/sdcc-user
