Hi All,
Recently I've noticed that signal levels have been down on 20m on my
K3/10. At first, I thought it was just band condx and didn't pay much
attention to it, but over the weekend I switched to the KX3 and signals
were much better - S-meter, P(X)3, and my ears...like maybe 30dB or so. 40
me
I use them in a lot of things and love them. They're lighter, slightly
higher voltage than alkaline (which are themselves higher than NiMH), they
maintain a flat voltage longer, and they handle in the cold or under high
loads (but not both) better.
My only caution is that, because the discharge cu
Thanks, that is actually on the data sheet, now that I look.
https://data.energizer.com/pdfs/l91.pdf
My biggest concern is whether they hold up under a 2+ A current draw. The data
sheet stops at 1 A.
wunder
K6WRU
Walter Underwood
CM87wj
http://observer.wunderwood.org/ (my blog)
> On May 9, 202
Hello Lee,My K3 developed a similar problem. It turned out to be D5 PIN diode
on the KXV3 Board. It's on its way back from Wilcox Engineering, W3DVX, and
should arrive tomorrow. I could hear a few very loud signals and transmitted
fine. I checked the usual, wrong antenna selected, RX antenna
I thought about quoting Jack Nicholson from A Few Good Men when he said
"well don't I feel like a" but thought better of it.
100% operator error. As diagnosed by N7GP and W0GHZ, I had my RX antenna
button pushed. I don't have an RX antenna, so I never push it...on
purpose.
I'm glad it wasn'
Glad you got it sorted out Lee73,Gary K9GS
Original message From: Lee Hiers Date:
5/11/23 5:21 PM (GMT-06:00) To: Elecraft Mailing List
Subject: Re: [Elecraft] K3 RX Issue? I thought about
quoting Jack Nicholson from A Few Good Men when he said"well don't I feel like
a"
Hello All,
I am looking to see if there is anyone out there interested in upgrading their
KPA500/KAT500 to the KPA1500 (plus some $). I really don’t need a legal limit
amp so I thought first I would check here to see if there is some interest.
Thanks for looking!
Michael
KK6RWK
Solana Beach, C
I have a K1 that I’m looking to sell, and took a look at the power output
before listing it. Power output is as follows:
40 meters 5.2 watts
30 meters 4.5 watts
20 meters 1.3 watts
17 meters 0.7 watts
These are obviously not the expected power output levels. Power supply voltage
= 12.8
Walter,
Like all primary cells they do have some ESR which is a little higher than
other secondary cell chemistries.
Like Julia I have pushed these cells towards 1A/cell at -30 celsius and
achieved reasonable results and the load curve is very flat.
The additional terminal voltage is good for ov
Hi Lee,
Do you also have a reduced RX signal level
on 30 meters as well as 20 meters, at least
by comparison with your KX3?
Since the TX output is OK, I will hazard a
guess that one of the relays in the
20/30M bandpass filter is not making
good contact or has developed a weak
solder joint on the
Thanks Mike - it was an ID-10T error: I had the RX antenna selected with
nothing on the RX antenna port.
73 de Lee, AA4GA
On Thu, May 11, 2023 at 9:47 PM Michael Carter wrote:
> Hi Lee,
>
> Do you also have a reduced RX signal level
> on 30 meters as well as 20 meters, at least
> by compariso
Hello David,
The same issue also exists in my two K1. Waiting for help
73,
Vincent BH5HTF
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailma
Numbers using the Elecraft 20 watt dummy load rather than resonated antennas:
40 M 4.8 W
30 M 5.5 W
20 M2.0 W
15 M1.7 W
Dave K9SW
> On May 11, 2023, at 6:52 PM, DAVID MOORMAN wrote:
>
> I have a K1 that I’m looking to sell, and took a look at the power output
> before listin
I would be interested. Have a KPA500 and KAT500Don, W4CBS Sent from my
T-Mobile 5G Device
Original message From: Michael Gillen via Elecraft
Date: 5/11/23 7:49 PM (GMT-05:00) To: Elecraft
Mailing List Subject: [Elecraft] For Trade: KPA1500
for KPA500/KAT500 + $ Hello All,I
14 matches
Mail list logo