Re: [Asterisk-Users] TE410P E1 Red Alarm
Hi, You could only take timing from one E1 per card. So you should use : span=1,1,0,ccs,hdb3,crc4 span=2,0,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 instead of : span=1,1,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,1,0,ccs,hdb3,crc4 span=4,1,0,ccs,hdb3,crc4 Le dimanche 25 décembre 2005 à 03:07 -0600, Diyanat Ali a écrit : Hello! I have a TE410P quad span card with 4 E1, i am using asterisk 1.2.1, i was using it without any issues earlier with just 1 E1 on span 1 and i recently plugged in 3 more E1's, only span 1 is working, the e1 for span 1 is from a different provider then the rest, the settings are same for both, but i constantly get red alaram on the span 2,3,4, i tried all settings, including the timming source , framing, coding , signalling type etc, without any sucesss what maybe the cause of the red alarm Regards Diyanat lspci -vvv 06:01.0 Communication controller: Unknown device d161:0410 (rev 02) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium TAbort- TAbort- MAbort- SERR- PERR- Latency: 64 Interrupt: pin A routed to IRQ 74 Region 0: Memory at fdff (32-bit, non-prefetchable) [size=128] lsmod Module Size Used byNot tainted wct4xxp78432 124 zaptel183776 250 [wct4xxp] cat /proc/zaptel/* Span 1: TE4/0/1 T4XXP (PCI) Card 0 Span 1 HDB3/CCS/CRC4 1 TE4/0/1/1 Clear (In use) upto 16 TE4/0/1/16 HDLCFCS (In use) upto 31 TE4/0/1/31 Clear (In use) Span 2: TE4/0/2 T4XXP (PCI) Card 0 Span 2 HDB3/CCS/CRC4 RED 32 TE4/0/2/1 Clear (In use) upto 47 TE4/0/2/16 HDLCFCS (In use) upto 62 TE4/0/2/31 Clear (In use) Span 3: TE4/0/3 T4XXP (PCI) Card 0 Span 3 HDB3/CCS/CRC4 RED 63 TE4/0/3/1 Clear (In use) upto 78 TE4/0/3/16 HDLCFCS (In use) upto 93 TE4/0/3/31 Clear (In use) Span 4: TE4/0/4 T4XXP (PCI) Card 0 Span 4 HDB3/CCS/CRC4 RED 94 TE4/0/4/1 Clear (In use) upto 109 TE4/0/4/16 HDLCFCS (In use) upto 124 TE4/0/4/31 Clear (In use) ztcfg -v SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 4: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) 124 channels configured. zttool Alarms Span OK T4XXP (PCI) Card 0 Span 1 RED T4XXP (PCI) Card 0 Span 2 RED T4XXP (PCI) Card 0 Span 3 RED T4XXP (PCI) Card 0 Span 4 CLI zap show status Description Alarms IRQbpviol CRC4 T4XXP (PCI) Card 0 Span 1OK 0 0 0 T4XXP (PCI) Card 0 Span 2RED0 0 0 T4XXP (PCI) Card 0 Span 3RED0 0 0 T4XXP (PCI) Card 0 Span 4RED0 0 0 alpha*CLI pri show span 1 Primary D-channel: 16 Status: Provisioned, Up, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 1 T305 Timer: 3 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 alpha*CLI pri show span 2 Primary D-channel: 47 Status: Provisioned, In Alarm, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 1 T305 Timer: 3 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 its the same as span for the rest as upto span 4 CLIpri intense debug span 2 Unnumbered frame: SAPI: 00 C/R: 0 EA: 0 TEI: 000EA: 1 M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] 0 bytes of data Sending Set Asynchronous Balanced Mode Extended same for the rest zaptel.conf span=1,1,0,ccs,hdb3,crc4 bchan = 1-15 dchan = 16 bchan = 17-31 span=2,1,0,ccs,hdb3,crc4 bchan = 32-46 dchan = 47 bchan = 48-62 span=3,1,0,ccs,hdb3,crc4 bchan = 63-77 dchan = 78 bchan = 79-93 span=4,1,0,ccs,hdb3,crc4 bchan = 94-108 dchan = 109 bchan = 110-124 loadzone=se defaultzone=se zapata.conf [channels] language=us context=sip switchtype=euroisdn pridialplan=unknown prilocaldialplan=unknown signalling=pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes echotraining=yes cidsignalling=dtmf cidstart=ring rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 immediate=no callerid=asreceived group=1 channel = 1-15 channel = 17-31 group=2 channel = 32-46 channel = 48-62 group=3 channel = 63-77 channel =
Re: [Asterisk-Users] TE410P E1 Red Alarm
Olivier Perrin ha scritto: Hi, You could only take timing from one E1 per card. So you should use : span=1,1,0,ccs,hdb3,crc4 span=2,0,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 instead of : span=1,1,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,1,0,ccs,hdb3,crc4 span=4,1,0,ccs,hdb3,crc4 Anyway it always worked for me with timing = 1 for all spans, if I unplug one span I see a nessage about changing the timing source and all keeps working ... ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] TE410P E1 Red Alarm
Hello! I have a TE410P quad span card with 4 E1, i am using asterisk 1.2.1, i was using it without any issues earlier with just 1 E1 on span 1 and i recently plugged in 3 more E1's, only span 1 is working, the e1 for span 1 is from a different provider then the rest, the settings are same for both, but i constantly get red alaram on the span 2,3,4, i tried all settings, including the timming source , framing, coding , signalling type etc, without any sucesss what maybe the cause of the red alarm Regards Diyanat lspci -vvv 06:01.0 Communication controller: Unknown device d161:0410 (rev 02) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium TAbort- TAbort- MAbort- SERR- PERR- Latency: 64 Interrupt: pin A routed to IRQ 74 Region 0: Memory at fdff (32-bit, non-prefetchable) [size=128] lsmod Module Size Used byNot tainted wct4xxp78432 124 zaptel183776 250 [wct4xxp] cat /proc/zaptel/* Span 1: TE4/0/1 T4XXP (PCI) Card 0 Span 1 HDB3/CCS/CRC4 1 TE4/0/1/1 Clear (In use) upto 16 TE4/0/1/16 HDLCFCS (In use) upto 31 TE4/0/1/31 Clear (In use) Span 2: TE4/0/2 T4XXP (PCI) Card 0 Span 2 HDB3/CCS/CRC4 RED 32 TE4/0/2/1 Clear (In use) upto 47 TE4/0/2/16 HDLCFCS (In use) upto 62 TE4/0/2/31 Clear (In use) Span 3: TE4/0/3 T4XXP (PCI) Card 0 Span 3 HDB3/CCS/CRC4 RED 63 TE4/0/3/1 Clear (In use) upto 78 TE4/0/3/16 HDLCFCS (In use) upto 93 TE4/0/3/31 Clear (In use) Span 4: TE4/0/4 T4XXP (PCI) Card 0 Span 4 HDB3/CCS/CRC4 RED 94 TE4/0/4/1 Clear (In use) upto 109 TE4/0/4/16 HDLCFCS (In use) upto 124 TE4/0/4/31 Clear (In use) ztcfg -v SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 4: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) 124 channels configured. zttool Alarms Span OK T4XXP (PCI) Card 0 Span 1 RED T4XXP (PCI) Card 0 Span 2 RED T4XXP (PCI) Card 0 Span 3 RED T4XXP (PCI) Card 0 Span 4 CLI zap show status Description Alarms IRQbpviol CRC4 T4XXP (PCI) Card 0 Span 1OK 0 0 0 T4XXP (PCI) Card 0 Span 2RED0 0 0 T4XXP (PCI) Card 0 Span 3RED0 0 0 T4XXP (PCI) Card 0 Span 4RED0 0 0 alpha*CLI pri show span 1 Primary D-channel: 16 Status: Provisioned, Up, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 1 T305 Timer: 3 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 alpha*CLI pri show span 2 Primary D-channel: 47 Status: Provisioned, In Alarm, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 1 T305 Timer: 3 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 its the same as span for the rest as upto span 4 CLIpri intense debug span 2 Unnumbered frame: SAPI: 00 C/R: 0 EA: 0 TEI: 000EA: 1 M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] 0 bytes of data Sending Set Asynchronous Balanced Mode Extended same for the rest zaptel.conf span=1,1,0,ccs,hdb3,crc4 bchan = 1-15 dchan = 16 bchan = 17-31 span=2,1,0,ccs,hdb3,crc4 bchan = 32-46 dchan = 47 bchan = 48-62 span=3,1,0,ccs,hdb3,crc4 bchan = 63-77 dchan = 78 bchan = 79-93 span=4,1,0,ccs,hdb3,crc4 bchan = 94-108 dchan = 109 bchan = 110-124 loadzone=se defaultzone=se zapata.conf [channels] language=us context=sip switchtype=euroisdn pridialplan=unknown prilocaldialplan=unknown signalling=pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes echotraining=yes cidsignalling=dtmf cidstart=ring rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 immediate=no callerid=asreceived group=1 channel = 1-15 channel = 17-31 group=2 channel = 32-46 channel = 48-62 group=3 channel = 63-77 channel = 79-93 group=4 channel = 94-108 channel = 110-124 ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
RE: [Asterisk-Users] TE410P E1 Red Alarm
Firstly, try unplugging span 1 and plug it into spans 2,3,4 in turn to check the port. Secondly, try E1 crossover cables in the remaining red-alarm spans. Regards, Mark -Original Message- From: Diyanat Ali [mailto:[EMAIL PROTECTED] Sent: Sunday, 25 December 2005 8:08 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] TE410P E1 Red Alarm Hello! I have a TE410P quad span card with 4 E1, i am using asterisk 1.2.1, i was using it without any issues earlier with just 1 E1 on span 1 and i recently plugged in 3 more E1's, only span 1 is working, the e1 for span 1 is from a different provider then the rest, the settings are same for both, but i constantly get red alaram on the span 2,3,4, i tried all settings, including the timming source , framing, coding , signalling type etc, without any sucesss what maybe the cause of the red alarm Regards Diyanat lspci -vvv 06:01.0 Communication controller: Unknown device d161:0410 (rev 02) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium TAbort- TAbort- MAbort- SERR- PERR- Latency: 64 Interrupt: pin A routed to IRQ 74 Region 0: Memory at fdff (32-bit, non-prefetchable) [size=128] lsmod Module Size Used byNot tainted wct4xxp78432 124 zaptel183776 250 [wct4xxp] cat /proc/zaptel/* Span 1: TE4/0/1 T4XXP (PCI) Card 0 Span 1 HDB3/CCS/CRC4 1 TE4/0/1/1 Clear (In use) upto 16 TE4/0/1/16 HDLCFCS (In use) upto 31 TE4/0/1/31 Clear (In use) Span 2: TE4/0/2 T4XXP (PCI) Card 0 Span 2 HDB3/CCS/CRC4 RED 32 TE4/0/2/1 Clear (In use) upto 47 TE4/0/2/16 HDLCFCS (In use) upto 62 TE4/0/2/31 Clear (In use) Span 3: TE4/0/3 T4XXP (PCI) Card 0 Span 3 HDB3/CCS/CRC4 RED 63 TE4/0/3/1 Clear (In use) upto 78 TE4/0/3/16 HDLCFCS (In use) upto 93 TE4/0/3/31 Clear (In use) Span 4: TE4/0/4 T4XXP (PCI) Card 0 Span 4 HDB3/CCS/CRC4 RED 94 TE4/0/4/1 Clear (In use) upto 109 TE4/0/4/16 HDLCFCS (In use) upto 124 TE4/0/4/31 Clear (In use) ztcfg -v SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 4: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) 124 channels configured. zttool Alarms Span OK T4XXP (PCI) Card 0 Span 1 RED T4XXP (PCI) Card 0 Span 2 RED T4XXP (PCI) Card 0 Span 3 RED T4XXP (PCI) Card 0 Span 4 CLI zap show status Description Alarms IRQbpviol CRC4 T4XXP (PCI) Card 0 Span 1OK 0 0 0 T4XXP (PCI) Card 0 Span 2RED0 0 0 T4XXP (PCI) Card 0 Span 3RED0 0 0 T4XXP (PCI) Card 0 Span 4RED0 0 0 alpha*CLI pri show span 1 Primary D-channel: 16 Status: Provisioned, Up, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 1 T305 Timer: 3 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 alpha*CLI pri show span 2 Primary D-channel: 47 Status: Provisioned, In Alarm, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 1 T305 Timer: 3 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 its the same as span for the rest as upto span 4 CLIpri intense debug span 2 Unnumbered frame: SAPI: 00 C/R: 0 EA: 0 TEI: 000EA: 1 M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] 0 bytes of data Sending Set Asynchronous Balanced Mode Extended same for the rest zaptel.conf span=1,1,0,ccs,hdb3,crc4 bchan = 1-15 dchan = 16 bchan = 17-31 span=2,1,0,ccs,hdb3,crc4 bchan = 32-46 dchan = 47 bchan = 48-62 span=3,1,0,ccs,hdb3,crc4 bchan = 63-77 dchan = 78 bchan = 79-93 span=4,1,0,ccs,hdb3,crc4 bchan = 94-108 dchan = 109 bchan = 110-124 loadzone=se defaultzone=se zapata.conf [channels] language=us context=sip switchtype=euroisdn pridialplan=unknown prilocaldialplan=unknown signalling=pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes echotraining=yes cidsignalling=dtmf cidstart=ring rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 immediate=no callerid=asreceived group=1 channel = 1-15 channel = 17-31 group=2 channel = 32-46 channel = 48-62 group=3 channel = 63-77 channel = 79-93 group=4 channel = 94-108 channel = 110-124 ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options
Re: [Asterisk-Users] TE410P E1 Red Alarm
Pure guess... The red alarm is essentially suggesting there is no signal coming into the port. By signal I mean the low level pcm data clocking seen on any T1/E1 that is connected to a remote T1/E1 port (regardless of whether that device has been turned up for service or not). Possible causes... - might need a T1/E1 crossover cable (not the same as an ethernet crossover, but crossed pins have been published many times on this list and documented in the wiki) - your provider may still have a loopback on some of their equipment, which essentially disconnects their signals from your equipment - service provider may not have actually turned up your T1/E1 for use as yet - bad T1/E1 cable between your TE410P and their demarc - bad port(s) on your TE410P (although very unlikely) - wiring problems (maybe the telco terminated the T1/E1's incorrectly or in the wrong place) Hello! I have a TE410P quad span card with 4 E1, i am using asterisk 1.2.1, i was using it without any issues earlier with just 1 E1 on span 1 and i recently plugged in 3 more E1's, only span 1 is working, the e1 for span 1 is from a different provider then the rest, the settings are same for both, but i constantly get red alaram on the span 2,3,4, i tried all settings, including the timming source , framing, coding , signalling type etc, without any sucesss what maybe the cause of the red alarm Regards Diyanat lspci -vvv 06:01.0 Communication controller: Unknown device d161:0410 (rev 02) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium TAbort- TAbort- MAbort- SERR- PERR- Latency: 64 Interrupt: pin A routed to IRQ 74 Region 0: Memory at fdff (32-bit, non-prefetchable) [size=128] lsmod Module Size Used byNot tainted wct4xxp78432 124 zaptel183776 250 [wct4xxp] cat /proc/zaptel/* Span 1: TE4/0/1 T4XXP (PCI) Card 0 Span 1 HDB3/CCS/CRC4 1 TE4/0/1/1 Clear (In use) upto 16 TE4/0/1/16 HDLCFCS (In use) upto 31 TE4/0/1/31 Clear (In use) Span 2: TE4/0/2 T4XXP (PCI) Card 0 Span 2 HDB3/CCS/CRC4 RED 32 TE4/0/2/1 Clear (In use) upto 47 TE4/0/2/16 HDLCFCS (In use) upto 62 TE4/0/2/31 Clear (In use) Span 3: TE4/0/3 T4XXP (PCI) Card 0 Span 3 HDB3/CCS/CRC4 RED 63 TE4/0/3/1 Clear (In use) upto 78 TE4/0/3/16 HDLCFCS (In use) upto 93 TE4/0/3/31 Clear (In use) Span 4: TE4/0/4 T4XXP (PCI) Card 0 Span 4 HDB3/CCS/CRC4 RED 94 TE4/0/4/1 Clear (In use) upto 109 TE4/0/4/16 HDLCFCS (In use) upto 124 TE4/0/4/31 Clear (In use) ztcfg -v SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 4: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) 124 channels configured. zttool Alarms Span OK T4XXP (PCI) Card 0 Span 1 RED T4XXP (PCI) Card 0 Span 2 RED T4XXP (PCI) Card 0 Span 3 RED T4XXP (PCI) Card 0 Span 4 CLI zap show status Description Alarms IRQbpviol CRC4 T4XXP (PCI) Card 0 Span 1OK 0 0 0 T4XXP (PCI) Card 0 Span 2RED0 0 0 T4XXP (PCI) Card 0 Span 3RED0 0 0 T4XXP (PCI) Card 0 Span 4RED0 0 0 alpha*CLI pri show span 1 Primary D-channel: 16 Status: Provisioned, Up, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 1 T305 Timer: 3 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 alpha*CLI pri show span 2 Primary D-channel: 47 Status: Provisioned, In Alarm, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 1 T305 Timer: 3 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 its the same as span for the rest as upto span 4 CLIpri intense debug span 2 Unnumbered frame: SAPI: 00 C/R: 0 EA: 0 TEI: 000EA: 1 M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] 0 bytes of data Sending Set Asynchronous Balanced Mode Extended same for the rest zaptel.conf span=1,1,0,ccs,hdb3,crc4 bchan = 1-15 dchan = 16 bchan = 17-31 span=2,1,0,ccs,hdb3,crc4 bchan = 32-46 dchan = 47 bchan = 48-62 span=3,1,0,ccs,hdb3,crc4 bchan = 63-77 dchan = 78 bchan = 79-93 span=4,1,0,ccs,hdb3,crc4 bchan = 94-108 dchan = 109 bchan = 110-124 loadzone=se defaultzone=se zapata.conf [channels] language=us context=sip
