Re: [Asterisk-Users] pri release cause code mismatch
Hi Guys, Been following this discussion, do you think these triggers could be a cause of our Nortel dropping some of our digits? ...keep getting: -- ACKing all packets from 118 to (but not including) 119 ..on an intense debug? Thanks, Michael Johann Steinwendtner wrote: Tirpák Miklós schrieb: Yes. 34 is required by the Nortel to send the call to an alternative destination. Cause 38 or 42 triggers the rerouting also for both options. Hans ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- MICHAEL TOOP Tel 011 602 9300 Fax 011 656 1342 Mobile 083 364 2370 Web www.bizcall.co.za ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] pri release cause code mismatch
Hi! On 09/14/05 16:51, Johann Steinwendtner wrote: Hi ! Asterisk sends a RELASE COMPLETE with cause code 34. It seems that Nortel expects a RELEASE message in this state. The conversion is done in the protocol engine of the MSDL. Why would you want the cause code 34 to be sent ? Do you need a special rerouting on the Nortel side ? Yes. 34 is required by the Nortel to send the call to an alternative destination. Would it be a help if you send a cause 3 ? (RELASE msg) No, I have already tried with PRI_CAUSE=3: Nortel just playes a tone instead of rerouting. It seems to be a DISCONNECT, not RELEASE: Protocol Discriminator: Q.931 (8) len=9 Call Ref: len= 2 (reference 64522/0xFC0A) (Terminator) Message type: DISCONNECT (69) [08 02 81 83] Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: Private network serving the local user (1) Ext: 1 Cause: No route to destination (3), class = Normal Event (0) ] -- Hungup 'Zap/31-1' Thanks, Miklos Best regards Hans Tirpák Miklós schrieb: Hi! My asterisk (1.0.7) is connected to a Nortel pbx with Digium E100P card, both side are ETSI EuroISDN. I would like to reject an incomming call with cause code 34, but the Nortel PBX gets the value of 31 instead of 34. It seems to work on the asterisk side: Protocol Discriminator: Q.931 (8) len=41 Call Ref: len= 2 (reference 17162/0x430A) (Originator) Message type: SETUP (5) ... Protocol Discriminator: Q.931 (8) len=9 Call Ref: len= 2 (reference 49930/0xC30A) (Terminator) Message type: RELEASE COMPLETE (90) [08 02 81 a2] Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: Private network serving the local user (1) Ext: 1 Cause: Circuit/channel congestion (34), class = Network Congestion (2) ] My macro looks like: exten = s,1,SetVar(PRI_CAUSE=34) exten = s,2,Hangup According to the debug on Nortel it gets 31 cause code in the release complete q.931 message. Do you have any idea? Thanks, Miklos ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] pri release cause code mismatch
Tirpák Miklós schrieb: Yes. 34 is required by the Nortel to send the call to an alternative destination. Cause 38 or 42 triggers the rerouting also for both options. Hans ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] pri release cause code mismatch
Hi! My asterisk (1.0.7) is connected to a Nortel pbx with Digium E100P card, both side are ETSI EuroISDN. I would like to reject an incomming call with cause code 34, but the Nortel PBX gets the value of 31 instead of 34. It seems to work on the asterisk side: Protocol Discriminator: Q.931 (8) len=41 Call Ref: len= 2 (reference 17162/0x430A) (Originator) Message type: SETUP (5) ... Protocol Discriminator: Q.931 (8) len=9 Call Ref: len= 2 (reference 49930/0xC30A) (Terminator) Message type: RELEASE COMPLETE (90) [08 02 81 a2] Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: Private network serving the local user (1) Ext: 1 Cause: Circuit/channel congestion (34), class = Network Congestion (2) ] My macro looks like: exten = s,1,SetVar(PRI_CAUSE=34) exten = s,2,Hangup According to the debug on Nortel it gets 31 cause code in the release complete q.931 message. Do you have any idea? Thanks, Miklos ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] pri release cause code mismatch
Hi ! Asterisk sends a RELASE COMPLETE with cause code 34. It seems that Nortel expects a RELEASE message in this state. The conversion is done in the protocol engine of the MSDL. Why would you want the cause code 34 to be sent ? Do you need a special rerouting on the Nortel side ? Would it be a help if you send a cause 3 ? (RELASE msg) Best regards Hans Tirpák Miklós schrieb: Hi! My asterisk (1.0.7) is connected to a Nortel pbx with Digium E100P card, both side are ETSI EuroISDN. I would like to reject an incomming call with cause code 34, but the Nortel PBX gets the value of 31 instead of 34. It seems to work on the asterisk side: Protocol Discriminator: Q.931 (8) len=41 Call Ref: len= 2 (reference 17162/0x430A) (Originator) Message type: SETUP (5) ... Protocol Discriminator: Q.931 (8) len=9 Call Ref: len= 2 (reference 49930/0xC30A) (Terminator) Message type: RELEASE COMPLETE (90) [08 02 81 a2] Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: Private network serving the local user (1) Ext: 1 Cause: Circuit/channel congestion (34), class = Network Congestion (2) ] My macro looks like: exten = s,1,SetVar(PRI_CAUSE=34) exten = s,2,Hangup According to the debug on Nortel it gets 31 cause code in the release complete q.931 message. Do you have any idea? Thanks, Miklos ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users