[OSL | CCIE_Voice] srst calling name
hi all, Assuming we been told to send calling name SiteC ph 2 in SRST mode call to PSTN. How do we achieve it it, if we ask to only use srst autoprovision all and srst autoprovision dn cause evertyme after u change Name to SiteC ph 2 from +6132 When you switch to UCM mode and back to SRST, it will overide tks for advice ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] MGCP Gateway requiring a reload
Yes, a sh isdn status showed multiple frame established. More often than not I have to actually apply: Serial 0/0/0:23 isdn bind-l3 ccm-manager Then no isdn bind-l3 ccm-manager isdn bind-l3 ccm-manager in order to get multiple frame established. In playing around with it today I figured out how to fix it without a reload. I noticed on the CUCM gateway page, I could see all 3 MGCP gateways registered to my sub however the IP address of the affected gateway showed as it's Loopback address. The functioning MGCP gateways showed an IP address that matched the interface I specified in the mgcp bind control and mgcp bind media commands I removed those commands on the affected gw then reapplied ... that fixed the issue and I didn't have to wait for a reload. Still don't know why it happens though ... KP Sent from my iPad On Jul 10, 2011, at 6:21 PM, Cristobal Priego cristobalpri...@gmail.com wrote: is your pri registered on UCM by the time you make your first call ? if you do a show isdn status what is the output ? 2011/7/10 CCIEVoiceKP ccievoic...@gmail.com I seem to be running into an intermittent problem with my MGCP gateways. I configure the router, its registered to CUCM, significant digits set correctly ... all is good except I can not receive inbound calls from the PSTN ... sometimes! A reload of the router fixes the issue when it happens. I just tested this with 3 mgcp gateways, all configured exactly the same ... one worked right away the other two needed to be reload in order to accept inbound calls. Is this a known issue that I've overlooked. Thanks. KP ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Can i Daisy Chain phones of Different device pool
Hi Roger, Thanks for the daisy chain assistance, i am very grateful, i will try it out. Regards Pithog oil --- On Fri, 7/1/11, Roger Carpio roger.car...@gmail.com wrote: From: Roger Carpio roger.car...@gmail.com Subject: Re: [OSL | CCIE_Voice] Can i Daisy Chain phones of Different device pool To: Pithog Oil pithog...@yahoo.com Cc: ccie_voice@onlinestudylist.com Date: Friday, July 1, 2011, 4:13 PM That shouldn't be a problem... Device Pool has nothing to do with daisy chain unless you're testing device mobility. In that situation it all depends if the switchports support dot1q so that PC port and Switch port reside on different VLANs. On Thu, Jun 30, 2011 at 8:42 AM, Pithog Oil pithog...@yahoo.com wrote: Hi Experts, Please i will like to know if i can daisy chain phones of different Device pools. Thanks for you assistance. Regards Pithog oil ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] MGCP Gateway requiring a reload
Hi - this is a bug with mgcp when using l0 http://www.onlinestudylist.com/archives/ccie_voice/2011-May/074217.html hth On Mon, Jul 11, 2011 at 9:36 AM, CCIEVoiceKP ccievoic...@gmail.com wrote: Yes, a sh isdn status showed multiple frame established. More often than not I have to actually apply: Serial 0/0/0:23 isdn bind-l3 ccm-manager Then no isdn bind-l3 ccm-manager isdn bind-l3 ccm-manager in order to get multiple frame established. In playing around with it today I figured out how to fix it without a reload. I noticed on the CUCM gateway page, I could see all 3 MGCP gateways registered to my sub however the IP address of the affected gateway showed as it's Loopback address. The functioning MGCP gateways showed an IP address that matched the interface I specified in the mgcp bind control and mgcp bind media commands I removed those commands on the affected gw then reapplied ... that fixed the issue and I didn't have to wait for a reload. Still don't know why it happens though ... KP Sent from my iPad On Jul 10, 2011, at 6:21 PM, Cristobal Priego cristobalpri...@gmail.com wrote: is your pri registered on UCM by the time you make your first call ? if you do a show isdn status what is the output ? 2011/7/10 CCIEVoiceKP ccievoic...@gmail.com I seem to be running into an intermittent problem with my MGCP gateways. I configure the router, its registered to CUCM, significant digits set correctly ... all is good except I can not receive inbound calls from the PSTN ... sometimes! A reload of the router fixes the issue when it happens. I just tested this with 3 mgcp gateways, all configured exactly the same ... one worked right away the other two needed to be reload in order to accept inbound calls. Is this a known issue that I've overlooked. Thanks. KP ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] B-acd - Not working
Hi All, Its working. It was h225 listen-port issue. I had it on 1820, resetting it back to 1720 (default) fixed the problem. Thanks once again. Sanoj___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] 17 Vouchers available
Hi everyone Sorry to be completely off topic. I am moving within this month and have some vouchers. Hoping my new location will have enough space for my own lab. So people who are looking for vouchers please let me know, and those with equipment, also please let me know, will be looking for some. Thanks Jon___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Invitation to connect on LinkedIn
LinkedIn Mark Drucker requested to add you as a connection on LinkedIn: -- Erwan, I'd like to add you to my professional network on LinkedIn. - Mark Accept invitation from Mark Drucker http://www.linkedin.com/e/hej71y-gpzn4uej-2/vVij78fy2eOUENWOQO0heO4E1Kn6V-1who-jwOgVZWdRhu/blk/I2951842706_2/1BpC5vrmRLoRZcjkkZt5YCpnlOt3RApnhMpmdzgmhxrSNBszYOnPoMdP8Qe34Rej99bQhdmClxjARAbPsRe3wPdPsVd3cLrCBxbOYWrSlI/EML_comm_afe/ View invitation from Mark Drucker http://www.linkedin.com/e/hej71y-gpzn4uej-2/vVij78fy2eOUENWOQO0heO4E1Kn6V-1who-jwOgVZWdRhu/blk/I2951842706_2/39vdz0TczgUcjkVcAALqnpPbOYWrSlI/svi/ -- Why might connecting with Mark Drucker be a good idea? Have a question? Mark Drucker's network will probably have an answer: You can use LinkedIn Answers to distribute your professional questions to Mark Drucker and your extended network. You can get high-quality answers from experienced professionals. http://www.linkedin.com/e/hej71y-gpzn4uej-2/ash/inv19_ayn/ -- (c) 2011, LinkedIn Corporation___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] WAN QoS MLP LFI
Cristobal, How did you resolve it? I've run into same problem. Thank you Date: Sun, 10 Jul 2011 15:32:52 -0700 From: Cristobal Priego cristobalpri...@gmail.com To: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] WAN QoS MLP LFI Message-ID: CAL3JcZBi9xDQv+1_K4HXDLu2JDKPt8BGfEu+rU8r7=es+ak...@mail.gmail.com Content-Type: text/plain; charset=iso-8859-1 nevermind i figured it out thanks 2011/7/10 Cristobal Priego cristobalpri...@gmail.com hello all I know we have address this issue several times i'm configuring MLP manually and this is how i have HQ configured int serial 0/0/1:0.1 bandwidth 384 int serial 0/0/1:0 frame-relay traffic-shapping class-map VOICE match ip dscp ef class-map match-any SIG match ip dscp cs3 match ip dscp af31policy-map VOIP class VOICE priority percent 33 class SIG bandwidth percent 5 class class-default fair-queuemap-class frame-relay myconfig frame-relay cir 384000 frame-relay mincir 384000 frame-relay be 0 frame-relay bc 3840int virtual-template 1 ip address 10.10.111.1 255.255.255.0 bandwidth 384 ppp multilink ppp multilint interleave ppp multilink fragment delay 10 service-policy out VOIPint serial 0/0/1:0.1 no ip add no frame-relay interface-dlci frame-relay interface-dlci 201 ppp virtual-template 1 no sh class myconfigBranch1 is pretty much the same when i reload Branch1 I lose connectivity to HQ so i go to HQ and go to the sub interface and remove frame-relay interface-dlci 201 ppp virtual-template1 add it back in do the same on branch1 and i have connectivity back however as soon as i reload either the branc1 or hq router I lose connectivity again and i have to issue the same workaround to get it to work again what do you guys recommend on this issue ? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] WAN QoS MLP LFI
sure no problem i configured MLP LFI manually and tested connectivity from BR2 and BR1 to HQ, BR2 no problems, because there's no virtual-template however from BR2 to HQ the connectivity was fine unless you reload BR2 router, once the router came back up, I lost connectivity to HQ and of course all the servers after that I tried reloading the HQ router, no difference same issue so i applied the following workaround I went to the sub-interface on BR2 router removed the frame-relay interface-dlci 201 ppp virtual-template 1 command re-added the command re-added the class-map to the fram-relay interface connectivity came back up however if you reload the BR2 router again, i was having the same problem so at the end what it did was fix the connectivity problem, once I had connectivity back, what i did is Reload HQ router once HQ came back up, I could reload Br2 router multiple times and the connectivity issue was resloved hope this helps 2011/7/11 Ronmac ron...@solcon.nl Hi, Maybe a hint on what was wrong? Share the knowledge. Send from my iPad2 Op 11 jul. 2011 om 00:32 heeft Cristobal Priego cristobalpri...@gmail.com het volgende geschreven: nevermind i figured it out thanks 2011/7/10 Cristobal Priego cristobalpri...@gmail.com cristobalpri...@gmail.com hello all I know we have address this issue several times i'm configuring MLP manually and this is how i have HQ configured int serial 0/0/1:0.1 bandwidth 384 int serial 0/0/1:0 frame-relay traffic-shapping class-map VOICE match ip dscp ef class-map match-any SIG match ip dscp cs3 match ip dscp af31 policy-map VOIP class VOICE priority percent 33 class SIG bandwidth percent 5 class class-default fair-queue map-class frame-relay myconfig frame-relay cir 384000 frame-relay mincir 384000 frame-relay be 0 frame-relay bc 3840 int virtual-template 1 ip address 10.10.111.1 255.255.255.0 bandwidth 384 ppp multilink ppp multilint interleave ppp multilink fragment delay 10 service-policy out VOIP int serial 0/0/1:0.1 no ip add no frame-relay interface-dlci frame-relay interface-dlci 201 ppp virtual-template 1 no sh class myconfig Branch1 is pretty much the same when i reload Branch1 I lose connectivity to HQ so i go to HQ and go to the sub interface and remove frame-relay interface-dlci 201 ppp virtual-template1 add it back in do the same on branch1 and i have connectivity back however as soon as i reload either the branc1 or hq router I lose connectivity again and i have to issue the same workaround to get it to work again what do you guys recommend on this issue ? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] QRT logs
hello all cold you please let me know if the jitter shown on the QRT reports is one way or round trip ? thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] CME H323 signal and media packet source
hi expert, if a customer ask you to source H323 signal and media from voice vlan interface on CME router then what commands be issued? i would do following: 1) Telephony-service ip source address voice vlan interface ip address 2) int vlan voice vlan id h323 v b s voice vlan ip add Is this what you would do or something else? thanks -adil -- .. . . _7___|___|_|_|adil.sha...@gmail.com . . ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Study partner in Maryland
Hi all, Sorry for a bit of off topic. I live in columbia, md. Please let me know anybody interested in study group. Thanks. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CME H323 signal and media packet source
on h323 that command h323-gateway v b s voice vlan ip addr binds the media and the control signaling to that ip address 2011/7/11 Adil Shaikh adil.sha...@gmail.com hi expert, if a customer ask you to source H323 signal and media from voice vlan interface on CME router then what commands be issued? i would do following: 1) Telephony-service ip source address voice vlan interface ip address 2) int vlan voice vlan id h323 v b s voice vlan ip add Is this what you would do or something else? thanks -adil -- .. . . _7___|___|_|_|adil.sha...@gmail.com . . ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Privacy Button in CME SRST
Hi All, Hi , In CME SRST mode , we configured the privacy button in the SRST ephone template. Privacy button configured in the CM mode also. Even though enough of button available in the phone we couldn't get the privacy button ? How to proceed further on this ?___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] BLF Speed dial in SRST
Hi All, Is there any other way to preserve the BLF Key in SRST mode ? Thanks___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com