Re: [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
Hi Roger, So what you trying to do is that PSTN Caller -- ephone-dn(x3006) -- cfa vm -- outgoing xlation-rule Why do we need to change redirecting-number? Since its already 3006. Also,if perform cfa, what about caller from HQ/BR1? As BR2 is under SRST, HQ/BR1 will reach BR2 via PSTN as well, this will cause them to be directed to vm directly also right? Thanks Shingei On Mon, Apr 11, 2011 at 1:30 PM, Rogers Ochieng rogersochi...@gmail.comwrote: Off the top of my head am thinking do call forward all and apply outgoing voice translation rule under the ephone-dn to change your redirecting number. On 11 April 2011 07:47, ShinGei Yong shingei.y...@gmail.com wrote: Hi all, I'm following up the same question that i posted last month, regarding the PSTN call diversion to BR2 CUE Voicemail during SRST.I was got confuse by the question,but looking at it to question PGuide, i think my understanding is correct. The question is asking, Ensure that the caller from PSTN who have dialed BR2 phone can be routed to Voicemail when there is a WAN outage at the BR2 site. In PGuide, the BR2 DN has CFUR external checked.So my understanding is that,when PSTN caller call BR2 phone,it should be routed to voicemail immediately,which CUE is locally located. My question is,how do achieve that PSTN caller enter Voicemail immediately without ringing the BR2 phone but allowing call from HQ/BR1 ring the destination and enter voicemail when CFNA or CFB. Anyone complete this section successfully?May share the idea? Shingei On Tue, Mar 8, 2011 at 11:16 PM, Rogers Ochieng rogersochi...@gmail.comwrote: Looking at that question the wording there does not specify that you need to send calls immediately to voicemail but that PSTN calls to BR2 can be routed to VM, it doesn't say at what state so to send VM so PSTN calls to BR2 busy and no answer states should meet the requirement. On 8 March 2011 18:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Rogers, Yes, and again, as stated below, i'm able to achieved CFB and CFNA during SRST, so in other words,the required dial-peer and setting to route call to CUE is already done,right? And HQ/BR1 phone is able to call BR2 phone via PSTN during SRST. Maybe put the question in this way: PSTN caller which originate from HQ/BR1, ring the destination during SRST.(I've done this) PSTN caller which originate from PSTN, to Voicemail without ringing BR2 phones during SRST Is the second requirement possible? Shingei. On Tue, Mar 8, 2011 at 10:26 PM, Rogers Ochieng rogersochi...@gmail.com wrote: AS you've stated you are using CUE which in normal operations you've integrated using jtapi CUE integration, i assuem the CUE module is on the BR2 router. So for SRST create a voip dial-peer using sip protocol and codec g711ulaw, dtmf sip-notify, to route calls to CUE and set CFB and CFNA, setup CUE sip settings. For HQ and BR1 to access BR2 setup CFUR On 8 March 2011 16:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, As stated below, i'm able to achieved that PSTN caller routed to VM when CFB and CFNA. Alsothere's no CUC in this lab. how to achieve that PSTN caller will be route to VM while allowing HQ or BR1 ring the destination in SRST site? TIA Shingei 2011/3/8 Roger Källberg roger.kallb...@cygate.se You need to setup CFB CFNA in an SRST situation, so that it sends the call over PSTN to CUC VM. Sincerely *Roger Källberg* CCIE #26199 (Voice) Consultant Cygate AB Eric Perssons väg 21, SE-217 62 MALMÖ -- *Från:* ShinGei Yong [shingei.y...@gmail.com] *Skickat:* den 8 mars 2011 11:00 *Till:* ccie_voice@onlinestudylist.com *Ämne:* [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward Unregisterd Int and External been checked(VM),but how the UCM instruct PSTN call to VM?The PSTN call will hitting the BR2 GW directly due to SRST. Am i thinking of too much? Shingei ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please
Re: [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
That's why i had wondered what the purpose is. I don't see a way unless you want to match all PSTN except HQ/BR1 numbers then translate those to go to VM and let thw HQ/BR1 go through the normal CFB and CFNA On 11 April 2011 09:16, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, So what you trying to do is that PSTN Caller -- ephone-dn(x3006) -- cfa vm -- outgoing xlation-rule Why do we need to change redirecting-number? Since its already 3006. Also,if perform cfa, what about caller from HQ/BR1? As BR2 is under SRST, HQ/BR1 will reach BR2 via PSTN as well, this will cause them to be directed to vm directly also right? Thanks Shingei On Mon, Apr 11, 2011 at 1:30 PM, Rogers Ochieng rogersochi...@gmail.comwrote: Off the top of my head am thinking do call forward all and apply outgoing voice translation rule under the ephone-dn to change your redirecting number. On 11 April 2011 07:47, ShinGei Yong shingei.y...@gmail.com wrote: Hi all, I'm following up the same question that i posted last month, regarding the PSTN call diversion to BR2 CUE Voicemail during SRST.I was got confuse by the question,but looking at it to question PGuide, i think my understanding is correct. The question is asking, Ensure that the caller from PSTN who have dialed BR2 phone can be routed to Voicemail when there is a WAN outage at the BR2 site. In PGuide, the BR2 DN has CFUR external checked.So my understanding is that,when PSTN caller call BR2 phone,it should be routed to voicemail immediately,which CUE is locally located. My question is,how do achieve that PSTN caller enter Voicemail immediately without ringing the BR2 phone but allowing call from HQ/BR1 ring the destination and enter voicemail when CFNA or CFB. Anyone complete this section successfully?May share the idea? Shingei On Tue, Mar 8, 2011 at 11:16 PM, Rogers Ochieng rogersochi...@gmail.com wrote: Looking at that question the wording there does not specify that you need to send calls immediately to voicemail but that PSTN calls to BR2 can be routed to VM, it doesn't say at what state so to send VM so PSTN calls to BR2 busy and no answer states should meet the requirement. On 8 March 2011 18:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Rogers, Yes, and again, as stated below, i'm able to achieved CFB and CFNA during SRST, so in other words,the required dial-peer and setting to route call to CUE is already done,right? And HQ/BR1 phone is able to call BR2 phone via PSTN during SRST. Maybe put the question in this way: PSTN caller which originate from HQ/BR1, ring the destination during SRST.(I've done this) PSTN caller which originate from PSTN, to Voicemail without ringing BR2 phones during SRST Is the second requirement possible? Shingei. On Tue, Mar 8, 2011 at 10:26 PM, Rogers Ochieng rogersochi...@gmail.com wrote: AS you've stated you are using CUE which in normal operations you've integrated using jtapi CUE integration, i assuem the CUE module is on the BR2 router. So for SRST create a voip dial-peer using sip protocol and codec g711ulaw, dtmf sip-notify, to route calls to CUE and set CFB and CFNA, setup CUE sip settings. For HQ and BR1 to access BR2 setup CFUR On 8 March 2011 16:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, As stated below, i'm able to achieved that PSTN caller routed to VM when CFB and CFNA. Alsothere's no CUC in this lab. how to achieve that PSTN caller will be route to VM while allowing HQ or BR1 ring the destination in SRST site? TIA Shingei 2011/3/8 Roger Källberg roger.kallb...@cygate.se You need to setup CFB CFNA in an SRST situation, so that it sends the call over PSTN to CUC VM. Sincerely *Roger Källberg* CCIE #26199 (Voice) Consultant Cygate AB Eric Perssons väg 21, SE-217 62 MALMÖ -- *Från:* ShinGei Yong [shingei.y...@gmail.com] *Skickat:* den 8 mars 2011 11:00 *Till:* ccie_voice@onlinestudylist.com *Ämne:* [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward Unregisterd Int and External been checked(VM),but how the UCM instruct PSTN call to VM?The PSTN call will hitting the BR2 GW directly due to SRST. Am i thinking of too much? Shingei ___ For more information regarding industry leading CCIE Lab training, please visit
Re: [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
Hi Roger, That's what i'm wondering too,but the fact is that, this is what the question request. The PGuide doesn't given too much of explanation of this. Anyone who completed this question may provide some hints? Thanks Shingei. On Mon, Apr 11, 2011 at 2:26 PM, Rogers Ochieng rogersochi...@gmail.comwrote: That's why i had wondered what the purpose is. I don't see a way unless you want to match all PSTN except HQ/BR1 numbers then translate those to go to VM and let thw HQ/BR1 go through the normal CFB and CFNA On 11 April 2011 09:16, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, So what you trying to do is that PSTN Caller -- ephone-dn(x3006) -- cfa vm -- outgoing xlation-rule Why do we need to change redirecting-number? Since its already 3006. Also,if perform cfa, what about caller from HQ/BR1? As BR2 is under SRST, HQ/BR1 will reach BR2 via PSTN as well, this will cause them to be directed to vm directly also right? Thanks Shingei On Mon, Apr 11, 2011 at 1:30 PM, Rogers Ochieng rogersochi...@gmail.comwrote: Off the top of my head am thinking do call forward all and apply outgoing voice translation rule under the ephone-dn to change your redirecting number. On 11 April 2011 07:47, ShinGei Yong shingei.y...@gmail.com wrote: Hi all, I'm following up the same question that i posted last month, regarding the PSTN call diversion to BR2 CUE Voicemail during SRST.I was got confuse by the question,but looking at it to question PGuide, i think my understanding is correct. The question is asking, Ensure that the caller from PSTN who have dialed BR2 phone can be routed to Voicemail when there is a WAN outage at the BR2 site. In PGuide, the BR2 DN has CFUR external checked.So my understanding is that,when PSTN caller call BR2 phone,it should be routed to voicemail immediately,which CUE is locally located. My question is,how do achieve that PSTN caller enter Voicemail immediately without ringing the BR2 phone but allowing call from HQ/BR1 ring the destination and enter voicemail when CFNA or CFB. Anyone complete this section successfully?May share the idea? Shingei On Tue, Mar 8, 2011 at 11:16 PM, Rogers Ochieng rogersochi...@gmail.com wrote: Looking at that question the wording there does not specify that you need to send calls immediately to voicemail but that PSTN calls to BR2 can be routed to VM, it doesn't say at what state so to send VM so PSTN calls to BR2 busy and no answer states should meet the requirement. On 8 March 2011 18:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Rogers, Yes, and again, as stated below, i'm able to achieved CFB and CFNA during SRST, so in other words,the required dial-peer and setting to route call to CUE is already done,right? And HQ/BR1 phone is able to call BR2 phone via PSTN during SRST. Maybe put the question in this way: PSTN caller which originate from HQ/BR1, ring the destination during SRST.(I've done this) PSTN caller which originate from PSTN, to Voicemail without ringing BR2 phones during SRST Is the second requirement possible? Shingei. On Tue, Mar 8, 2011 at 10:26 PM, Rogers Ochieng rogersochi...@gmail.com wrote: AS you've stated you are using CUE which in normal operations you've integrated using jtapi CUE integration, i assuem the CUE module is on the BR2 router. So for SRST create a voip dial-peer using sip protocol and codec g711ulaw, dtmf sip-notify, to route calls to CUE and set CFB and CFNA, setup CUE sip settings. For HQ and BR1 to access BR2 setup CFUR On 8 March 2011 16:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, As stated below, i'm able to achieved that PSTN caller routed to VM when CFB and CFNA. Alsothere's no CUC in this lab. how to achieve that PSTN caller will be route to VM while allowing HQ or BR1 ring the destination in SRST site? TIA Shingei 2011/3/8 Roger Källberg roger.kallb...@cygate.se You need to setup CFB CFNA in an SRST situation, so that it sends the call over PSTN to CUC VM. Sincerely *Roger Källberg* CCIE #26199 (Voice) Consultant Cygate AB Eric Perssons väg 21, SE-217 62 MALMÖ -- *Från:* ShinGei Yong [shingei.y...@gmail.com] *Skickat:* den 8 mars 2011 11:00 *Till:* ccie_voice@onlinestudylist.com *Ämne:* [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward
Re: [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
The way I interprete it is that when the BR2 SRST phone is ringing, it can be sent to voicemail. I would think this would include call-forward all, call-forward noan, call-forward busy, and possibly transfer to voicemail. You can acheive this by having a dial-peer for the voicemail pilot that expands to the PSTN number for voicemail. Turn on Redirect IE delivery for inbound calls on the HQ gateway. Redirect IE element will now include the BR2 SRST phone's extension when sent over the PSTN. Adam Compton On Mon, Apr 11, 2011 at 12:47 AM, ShinGei Yong shingei.y...@gmail.comwrote: Hi all, I'm following up the same question that i posted last month, regarding the PSTN call diversion to BR2 CUE Voicemail during SRST.I was got confuse by the question,but looking at it to question PGuide, i think my understanding is correct. The question is asking, Ensure that the caller from PSTN who have dialed BR2 phone can be routed to Voicemail when there is a WAN outage at the BR2 site. In PGuide, the BR2 DN has CFUR external checked.So my understanding is that,when PSTN caller call BR2 phone,it should be routed to voicemail immediately,which CUE is locally located. My question is,how do achieve that PSTN caller enter Voicemail immediately without ringing the BR2 phone but allowing call from HQ/BR1 ring the destination and enter voicemail when CFNA or CFB. Anyone complete this section successfully?May share the idea? Shingei On Tue, Mar 8, 2011 at 11:16 PM, Rogers Ochieng rogersochi...@gmail.comwrote: Looking at that question the wording there does not specify that you need to send calls immediately to voicemail but that PSTN calls to BR2 can be routed to VM, it doesn't say at what state so to send VM so PSTN calls to BR2 busy and no answer states should meet the requirement. On 8 March 2011 18:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Rogers, Yes, and again, as stated below, i'm able to achieved CFB and CFNA during SRST, so in other words,the required dial-peer and setting to route call to CUE is already done,right? And HQ/BR1 phone is able to call BR2 phone via PSTN during SRST. Maybe put the question in this way: PSTN caller which originate from HQ/BR1, ring the destination during SRST.(I've done this) PSTN caller which originate from PSTN, to Voicemail without ringing BR2 phones during SRST Is the second requirement possible? Shingei. On Tue, Mar 8, 2011 at 10:26 PM, Rogers Ochieng rogersochi...@gmail.com wrote: AS you've stated you are using CUE which in normal operations you've integrated using jtapi CUE integration, i assuem the CUE module is on the BR2 router. So for SRST create a voip dial-peer using sip protocol and codec g711ulaw, dtmf sip-notify, to route calls to CUE and set CFB and CFNA, setup CUE sip settings. For HQ and BR1 to access BR2 setup CFUR On 8 March 2011 16:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, As stated below, i'm able to achieved that PSTN caller routed to VM when CFB and CFNA. Alsothere's no CUC in this lab. how to achieve that PSTN caller will be route to VM while allowing HQ or BR1 ring the destination in SRST site? TIA Shingei 2011/3/8 Roger Källberg roger.kallb...@cygate.se You need to setup CFB CFNA in an SRST situation, so that it sends the call over PSTN to CUC VM. Sincerely *Roger Källberg* CCIE #26199 (Voice) Consultant Cygate AB Eric Perssons väg 21, SE-217 62 MALMÖ -- *Från:* ShinGei Yong [shingei.y...@gmail.com] *Skickat:* den 8 mars 2011 11:00 *Till:* ccie_voice@onlinestudylist.com *Ämne:* [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward Unregisterd Int and External been checked(VM),but how the UCM instruct PSTN call to VM?The PSTN call will hitting the BR2 GW directly due to SRST. Am i thinking of too much? Shingei ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
Hi all, I'm following up the same question that i posted last month, regarding the PSTN call diversion to BR2 CUE Voicemail during SRST.I was got confuse by the question,but looking at it to question PGuide, i think my understanding is correct. The question is asking, Ensure that the caller from PSTN who have dialed BR2 phone can be routed to Voicemail when there is a WAN outage at the BR2 site. In PGuide, the BR2 DN has CFUR external checked.So my understanding is that,when PSTN caller call BR2 phone,it should be routed to voicemail immediately,which CUE is locally located. My question is,how do achieve that PSTN caller enter Voicemail immediately without ringing the BR2 phone but allowing call from HQ/BR1 ring the destination and enter voicemail when CFNA or CFB. Anyone complete this section successfully?May share the idea? Shingei On Tue, Mar 8, 2011 at 11:16 PM, Rogers Ochieng rogersochi...@gmail.comwrote: Looking at that question the wording there does not specify that you need to send calls immediately to voicemail but that PSTN calls to BR2 can be routed to VM, it doesn't say at what state so to send VM so PSTN calls to BR2 busy and no answer states should meet the requirement. On 8 March 2011 18:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Rogers, Yes, and again, as stated below, i'm able to achieved CFB and CFNA during SRST, so in other words,the required dial-peer and setting to route call to CUE is already done,right? And HQ/BR1 phone is able to call BR2 phone via PSTN during SRST. Maybe put the question in this way: PSTN caller which originate from HQ/BR1, ring the destination during SRST.(I've done this) PSTN caller which originate from PSTN, to Voicemail without ringing BR2 phones during SRST Is the second requirement possible? Shingei. On Tue, Mar 8, 2011 at 10:26 PM, Rogers Ochieng rogersochi...@gmail.comwrote: AS you've stated you are using CUE which in normal operations you've integrated using jtapi CUE integration, i assuem the CUE module is on the BR2 router. So for SRST create a voip dial-peer using sip protocol and codec g711ulaw, dtmf sip-notify, to route calls to CUE and set CFB and CFNA, setup CUE sip settings. For HQ and BR1 to access BR2 setup CFUR On 8 March 2011 16:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, As stated below, i'm able to achieved that PSTN caller routed to VM when CFB and CFNA. Alsothere's no CUC in this lab. how to achieve that PSTN caller will be route to VM while allowing HQ or BR1 ring the destination in SRST site? TIA Shingei 2011/3/8 Roger Källberg roger.kallb...@cygate.se You need to setup CFB CFNA in an SRST situation, so that it sends the call over PSTN to CUC VM. Sincerely *Roger Källberg* CCIE #26199 (Voice) Consultant Cygate AB Eric Perssons väg 21, SE-217 62 MALMÖ -- *Från:* ShinGei Yong [shingei.y...@gmail.com] *Skickat:* den 8 mars 2011 11:00 *Till:* ccie_voice@onlinestudylist.com *Ämne:* [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward Unregisterd Int and External been checked(VM),but how the UCM instruct PSTN call to VM?The PSTN call will hitting the BR2 GW directly due to SRST. Am i thinking of too much? Shingei ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward Unregisterd Int and External been checked(VM),but how the UCM instruct PSTN call to VM?The PSTN call will hitting the BR2 GW directly due to SRST. Am i thinking of too much? Shingei ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
Hi Roger, As stated below, i'm able to achieved that PSTN caller routed to VM when CFB and CFNA. Alsothere's no CUC in this lab. how to achieve that PSTN caller will be route to VM while allowing HQ or BR1 ring the destination in SRST site? TIA Shingei 2011/3/8 Roger Källberg roger.kallb...@cygate.se You need to setup CFB CFNA in an SRST situation, so that it sends the call over PSTN to CUC VM. Sincerely *Roger Källberg* CCIE #26199 (Voice) Consultant Cygate AB Eric Perssons väg 21, SE-217 62 MALMÖ -- *Från:* ShinGei Yong [shingei.y...@gmail.com] *Skickat:* den 8 mars 2011 11:00 *Till:* ccie_voice@onlinestudylist.com *Ämne:* [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward Unregisterd Int and External been checked(VM),but how the UCM instruct PSTN call to VM?The PSTN call will hitting the BR2 GW directly due to SRST. Am i thinking of too much? Shingei ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
AS you've stated you are using CUE which in normal operations you've integrated using jtapi CUE integration, i assuem the CUE module is on the BR2 router. So for SRST create a voip dial-peer using sip protocol and codec g711ulaw, dtmf sip-notify, to route calls to CUE and set CFB and CFNA, setup CUE sip settings. For HQ and BR1 to access BR2 setup CFUR On 8 March 2011 16:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, As stated below, i'm able to achieved that PSTN caller routed to VM when CFB and CFNA. Alsothere's no CUC in this lab. how to achieve that PSTN caller will be route to VM while allowing HQ or BR1 ring the destination in SRST site? TIA Shingei 2011/3/8 Roger Källberg roger.kallb...@cygate.se You need to setup CFB CFNA in an SRST situation, so that it sends the call over PSTN to CUC VM. Sincerely *Roger Källberg* CCIE #26199 (Voice) Consultant Cygate AB Eric Perssons väg 21, SE-217 62 MALMÖ -- *Från:* ShinGei Yong [shingei.y...@gmail.com] *Skickat:* den 8 mars 2011 11:00 *Till:* ccie_voice@onlinestudylist.com *Ämne:* [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward Unregisterd Int and External been checked(VM),but how the UCM instruct PSTN call to VM?The PSTN call will hitting the BR2 GW directly due to SRST. Am i thinking of too much? Shingei ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
Hi Rogers, Yes, and again, as stated below, i'm able to achieved CFB and CFNA during SRST, so in other words,the required dial-peer and setting to route call to CUE is already done,right? And HQ/BR1 phone is able to call BR2 phone via PSTN during SRST. Maybe put the question in this way: PSTN caller which originate from HQ/BR1, ring the destination during SRST.(I've done this) PSTN caller which originate from PSTN, to Voicemail without ringing BR2 phones during SRST Is the second requirement possible? Shingei. On Tue, Mar 8, 2011 at 10:26 PM, Rogers Ochieng rogersochi...@gmail.comwrote: AS you've stated you are using CUE which in normal operations you've integrated using jtapi CUE integration, i assuem the CUE module is on the BR2 router. So for SRST create a voip dial-peer using sip protocol and codec g711ulaw, dtmf sip-notify, to route calls to CUE and set CFB and CFNA, setup CUE sip settings. For HQ and BR1 to access BR2 setup CFUR On 8 March 2011 16:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, As stated below, i'm able to achieved that PSTN caller routed to VM when CFB and CFNA. Alsothere's no CUC in this lab. how to achieve that PSTN caller will be route to VM while allowing HQ or BR1 ring the destination in SRST site? TIA Shingei 2011/3/8 Roger Källberg roger.kallb...@cygate.se You need to setup CFB CFNA in an SRST situation, so that it sends the call over PSTN to CUC VM. Sincerely *Roger Källberg* CCIE #26199 (Voice) Consultant Cygate AB Eric Perssons väg 21, SE-217 62 MALMÖ -- *Från:* ShinGei Yong [shingei.y...@gmail.com] *Skickat:* den 8 mars 2011 11:00 *Till:* ccie_voice@onlinestudylist.com *Ämne:* [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward Unregisterd Int and External been checked(VM),but how the UCM instruct PSTN call to VM?The PSTN call will hitting the BR2 GW directly due to SRST. Am i thinking of too much? Shingei ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST
Looking at that question the wording there does not specify that you need to send calls immediately to voicemail but that PSTN calls to BR2 can be routed to VM, it doesn't say at what state so to send VM so PSTN calls to BR2 busy and no answer states should meet the requirement. On 8 March 2011 18:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Rogers, Yes, and again, as stated below, i'm able to achieved CFB and CFNA during SRST, so in other words,the required dial-peer and setting to route call to CUE is already done,right? And HQ/BR1 phone is able to call BR2 phone via PSTN during SRST. Maybe put the question in this way: PSTN caller which originate from HQ/BR1, ring the destination during SRST.(I've done this) PSTN caller which originate from PSTN, to Voicemail without ringing BR2 phones during SRST Is the second requirement possible? Shingei. On Tue, Mar 8, 2011 at 10:26 PM, Rogers Ochieng rogersochi...@gmail.comwrote: AS you've stated you are using CUE which in normal operations you've integrated using jtapi CUE integration, i assuem the CUE module is on the BR2 router. So for SRST create a voip dial-peer using sip protocol and codec g711ulaw, dtmf sip-notify, to route calls to CUE and set CFB and CFNA, setup CUE sip settings. For HQ and BR1 to access BR2 setup CFUR On 8 March 2011 16:05, ShinGei Yong shingei.y...@gmail.com wrote: Hi Roger, As stated below, i'm able to achieved that PSTN caller routed to VM when CFB and CFNA. Alsothere's no CUC in this lab. how to achieve that PSTN caller will be route to VM while allowing HQ or BR1 ring the destination in SRST site? TIA Shingei 2011/3/8 Roger Källberg roger.kallb...@cygate.se You need to setup CFB CFNA in an SRST situation, so that it sends the call over PSTN to CUC VM. Sincerely *Roger Källberg* CCIE #26199 (Voice) Consultant Cygate AB Eric Perssons väg 21, SE-217 62 MALMÖ -- *Från:* ShinGei Yong [shingei.y...@gmail.com] *Skickat:* den 8 mars 2011 11:00 *Till:* ccie_voice@onlinestudylist.com *Ämne:* [OSL | CCIE_Voice] Vol2 Lab 5 Question 4.2 CUE SRST Hi, The question stated,caller from PSTN CAN BE routed to VM when there's WAN outage at BR2. Internal caller from HQ or BR1 must be able to reach BR2 phone and forward to VM if no answer. To me,there are two meaning of the sentense 1. PSTN caller routed to VM immediately when there's WAN outage at BR2, 2. PSTN caller routed to VM when CFB or CFNA. What confuse me is that,how to achieve that the PSTN caller routed to VM immediately when there's a WAN outage at BR2?I'm able to achieved that PSTN caller router to VM when CFB and CFNA. In proctor guide, Forward Unregisterd Int and External been checked(VM),but how the UCM instruct PSTN call to VM?The PSTN call will hitting the BR2 GW directly due to SRST. Am i thinking of too much? Shingei ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com