Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone
I still think your problem most likely lies in the tech prefix on the CUBE. You don't need a tech prefix and I would make the dial-peer a little more specific. I'm not sure completely sure that this is accurate, but I would think that having a tech prefix on CUBE of 1# would not allow you route a call to it with 44#. I'm not 100% on that though. Also, with the IPIPGW not found error, it normally mean you have to bounce the gateway so that it registers as a IPIPGW. If you type in the gateway command prior to the allow connections command then the GW will not register as an IPIPGW and even if you enter those commands unless it unregisters and registers again, the gatekeeper will not update on its own. Change the config to this: interface GigabitEthernet0/0 ip address 14.160.110.254 255.255.255.0 duplex auto speed auto media-type rj45 h323-gateway voip interface h323-gateway voip id CUBE ipaddr 14.160.110.129 1719 h323-gateway voip h323-id MJ-CUBE h323-gateway voip tech-prefix 1# (remove) h323-gateway voip bind srcaddr 14.160.110.254 voice service voip allow h t h allow s t h allow s t s allow h t s no gateway gateway dial-peer voice 100 voip incoming called-number 44# no vad dtmf-relay h245-signal codec g729r8 dial-peer voice 200 voip destination-pattern 44# session target ras no vad dtmf-relay h245-signal codec g729r8 Try the call again and do a debug gatekeeper main 10 to see if the gateway is selected. If the gateway is selected and the call still fails, then try an debug voip dialpeer on both routers, and also possibly a debug voice ipipgw on HQ. Hope this helps, Jeff From: Mritunjay Kumar [mailto:mjs...@gmail.com] Sent: Tuesday, November 30, 2010 9:28 AM To: Matthew Berry; Prashant Patel; givemeccievoice2...@gmail.com Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone Hi All , Might not be able to check my mails for 1-2 days . I will try to reply in case if any other information is needed. Regards, MJ On Tue, Nov 30, 2010 at 7:51 PM, Mritunjay Kumar wrote: Hi All, thanks for responding. Here is the scenario , config and result Scenario CME registered with 44# , CUCM and CUBE with 1# Call is faling from CUCM to CME only. output and config Gatekeep config gatekeeper zone local BR1 cisco.com 14.160.110.129 zone local CME cisco.com invia CUBE outvia CUBE zone local CUCM cisco.com invia CUBE outvia CUBE zone local CUBE cisco.com zone prefix CUCM 2... zone prefix CME 5... no shutdown BR1#sh gatek endpoints GATEKEEPER ENDPOINT REGISTRATION CallSignalAddr Port RASSignalAddr Port Zone Name TypeFlags --- - --- - - - 14.160.110.15 1720 14.160.110.15 32797 CUCM VOIP-GW ENDPOINT-ID: 71A5D3680003 VERSION: 5 AGE: 37 secs SupportsAnnexE: FALSE g_supp_prots: 0x0050 H323-ID: US_1 Voice Capacity Max.= Avail.= Current.= 0 14.160.115.200 1720 14.160.115.200 57052 CME H323-GW ENDPOINT-ID: 70B6E1940003 VERSION: 4 AGE: 13 secs SupportsAnnexE: FALSE g_supp_prots: 0x0050 E164-ID: 1234 E164-ID: 4321 E164-ID: 7000 H323-ID: MJ-CME Voice Capacity Max.= Avail.= Current.= 0 14.160.110.254 1720 14.160.110.254 56804 CUBE H323-GW ENDPOINT-ID: 681D6EDC0003 VERSION: 4 AGE: 21 secs SupportsAnnexE: FALSE g_supp_prots: 0x0050 H323-ID: MJ-CUBE Voice Capacity Max.= Avail.= Current.= 0 Total number of active registrations = 3 BR1#sh gatek gw-type-prefix BR1#sh gatek gw-type-prefix buffer used: 219, size: 20480 GATEWAY TYPE PREFIX TABLE = Prefix: 1#* Zone CUBE master gateway list: 14.160.110.254:1720 MJ-CUBE Zone CUCM master gateway list: 14.160.110.15:1720 US_1 Prefix: 44#* Zone CME master gateway list: 14.160.115.200:1720 MJ-CME CUBE config interface GigabitEthernet0/0 ip address 14.160.110.254 255.255.255.0 duplex auto speed auto media-type rj45 h323-gateway voip interface h323-gateway voip id CUBE ipaddr 14.160.110.129 1719 h323-gateway voip h323-id MJ-CUBE h323-gateway voip tech-prefix 1# h323-gateway voip bind srcaddr 14.160.110.254 dial-peer voice 100 voip incoming called-number . dial-peer voice 200 voip destination-pattern .T session target ras CME config interface GigabitEthernet0/0 ip address 14.160.115.200 255.255.255.0 duplex auto speed auto media-type rj45 h323-gateway voip interface h323-gateway voip id CME ipaddr 14.160.110.129 1719 h323-gateway voip h323-id MJ-CME h323-gateway voip tech-prefix 44# h323-gateway voip bind srcaddr 14.160.115.200 dial-peer voice 23 voip translation-profile incoming voip-in translation-profile outgoing voip-out destin
Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone
l is faling from both side. > > > Here is the debug for above > > > > > > Not sure but it is necessary that target ZONE and CUBE ie VIA zone should > be using same Tech Prefix ?? > > BR1# > *Nov 30 14:19:05.234: ////GK/gk_process: > QUEUE_EVENT (minor 0) wakeup > *Nov 30 14:19:05.234: ////GK/gk_rassrv_arq: > arqp=0x68A40104,crv=0x5, answerCall=0 > *Nov 30 14:19:05.234: ////GK/gk_rassrv_sep_arq: ARQ > Didn't use GK_AAA_PROC > *Nov 30 14:19:05.234: //003599EC0500/003599EC0500/GK/gk_dns_query: No Name > servers > *Nov 30 14:19:05.234: //003599EC0500/003599EC0500/GK/rassrv_get_addrinfo: > (44#5002) Matched tech-prefix 44# > *Nov 30 14:19:05.234: //003599EC0500/003599EC0500/GK/rassrv_get_addrinfo: > (44#5002) Matched zone prefix 5 and remainder 002 > *Nov 30 14:19:05.234: > ////GK/gk_rassrv_get_ingress_network: returning > default ingress network = 1 > *Nov 30 14:19:05.234: > //003599EC0500/003599EC0500/GK/rassrv_arq_select_viazone: about to check the > source side, src_zonep=0x68E3A82C > *Nov 30 14:19:05.234: > //003599EC0500/003599EC0500/GK/rassrv_arq_select_viazone: matched zone is > CUCM, and z_invianamelen=4 > *Nov 30 14:19:05.234: > //003599EC0500/003599EC0500/GK/rassrv_arq_select_viazone and > z_invianamep=CUBE > *Nov 30 14:19:05.234: > //003599EC0500/003599EC0500/GK/rassrv_arq_select_viazone(CUCM): Terminating > inbound call at the IPIPGW in zone CUBE > *Nov 30 14:19:05.234: > ////GK/gk_gw_select_ipipgw_random: zonep: > 0x70DEE310, tpp: 0x6C40F860, current_endpt: 0 > *Nov 30 14:19:05.234: > ////GK/gk_gw_select_ipipgw_random: Gateway selection > will start at the top of the linked list. use_count=0, current_endpt=0 > *Nov 30 14:19:05.234: > ////GK/gk_gw_select_ipipgw_random: qelemp=0x0, > loop_count=0 > *Nov 30 14:19:05.234: > ////GK/gk_gw_select_ipipgw_random: Could not find an > IPIPGW. > *Nov 30 14:19:05.234: > //003599EC0500/003599EC0500/GK/rassrv_get_addrinfo(44#5002): Viazone gateway > selection failed for zone "CUBE" > *Nov 30 14:19:05.234: //003599EC0500/003599EC0500/GK/gk_rassrv_sep_arq: > rassrv_get_addrinfo() failed (return code = 0x805) > *Nov 30 14:19:10.250: ////GK/gk_process: got a > TIMER event > > *Nov 30 14:19:10.250: ////GK/gk_handle_timers > > *Nov 30 14:19:10.250: ////GK/gk_handle_timers: > managed timer expired 0x6790DC78 > > > Not sure but it is necessary that target zone and VIA zone should be using > same tech prefix ? > > Let me know if any other information is needed. > > Regards, > MJ > > > > > > > On Tue, Nov 30, 2010 at 7:32 PM, Matthew Berry wrote: > >> Correct, you do not need to register your CUBE with a tech prefix at all. >> * >> * >> *Matthew Berry* >> >> **Sr. Voice Engineer - CCIE 26721 >> >> *[image: >> cid:image003.jpg@01C97C0E.9597F500]*<http://www.cdw.com/content/services/advanced-technology/default.aspx> >> ** >> >> *CDW Advanced Technology Services* >> >> 7145 Boone Avenue North | Brooklyn Park, MN 55428 >> >> Single Number Reach: +1.763.592.5987 >> >> matthew.be...@cdw.com >> >> From: "givemeccievoice2...@gmail.com" >> Date: Tue, 30 Nov 2010 07:49:07 -0600 >> To: 'Mritunjay Kumar' , "ccie_voice@onlinestudylist.com" >> >> Subject: Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone >> >> Why do you have a different tech prefix for VIA zone? I don’t believe you >> need a tech prefix at all for a VIA zone / CUBE. Just have your dial-peers >> configured to receive what CUCM is sending. >> >> >> >> Also, make sure that you have your “allow connections” commands. Do a >> show gatekeeper endpoints and CUBE should be registered as “H323-GW”. If >> not, make sure those commands are present and/or bounce the gateway command. >> >> >> >> Please post the debug gatekeeper main 10 output as well as show gatekeeper >> end. >> >> >> >> Jeff >> >> >> >> *From:* ccie_voice-boun...@onlinestudylist.com [ >> mailto:ccie_voice-boun...@onlinestudylist.com] >> *On Behalf Of *Mritunjay Kumar >> *Sent:* Tuesday, November 30, 2010 3:06 AM >> *To:* ccie_voice@onlinestudylist.com >> *Subject:* [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone >> >> >> >> Hi all , >> >> I am facing issue in GK
Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone
30 14:19:05.234: //003599EC0500/003599EC0500/GK/rassrv_arq_select_viazone: matched zone is CUCM, and z_invianamelen=4 *Nov 30 14:19:05.234: //003599EC0500/003599EC0500/GK/rassrv_arq_select_viazone and z_invianamep=CUBE *Nov 30 14:19:05.234: //003599EC0500/003599EC0500/GK/rassrv_arq_select_viazone(CUCM): Terminating inbound call at the IPIPGW in zone CUBE *Nov 30 14:19:05.234: ////GK/gk_gw_select_ipipgw_random: zonep: 0x70DEE310, tpp: 0x6C40F860, current_endpt: 0 *Nov 30 14:19:05.234: ////GK/gk_gw_select_ipipgw_random: Gateway selection will start at the top of the linked list. use_count=0, current_endpt=0 *Nov 30 14:19:05.234: ////GK/gk_gw_select_ipipgw_random: qelemp=0x0, loop_count=0 *Nov 30 14:19:05.234: ////GK/gk_gw_select_ipipgw_random: Could not find an IPIPGW. *Nov 30 14:19:05.234: //003599EC0500/003599EC0500/GK/rassrv_get_addrinfo(44#5002): Viazone gateway selection failed for zone "CUBE" *Nov 30 14:19:05.234: //003599EC0500/003599EC0500/GK/gk_rassrv_sep_arq: rassrv_get_addrinfo() failed (return code = 0x805) *Nov 30 14:19:10.250: ////GK/gk_process: got a TIMER event *Nov 30 14:19:10.250: ////GK/gk_handle_timers *Nov 30 14:19:10.250: ////GK/gk_handle_timers: managed timer expired 0x6790DC78 Not sure but it is necessary that target zone and VIA zone should be using same tech prefix ? Let me know if any other information is needed. Regards, MJ On Tue, Nov 30, 2010 at 7:32 PM, Matthew Berry wrote: > Correct, you do not need to register your CUBE with a tech prefix at all. > * > * > *Matthew Berry* > > **Sr. Voice Engineer - CCIE 26721 > > *[image: > cid:image003.jpg@01C97C0E.9597F500]*<http://www.cdw.com/content/services/advanced-technology/default.aspx> > ** > > *CDW Advanced Technology Services* > > 7145 Boone Avenue North | Brooklyn Park, MN 55428 > > Single Number Reach: +1.763.592.5987 > > matthew.be...@cdw.com > > From: "givemeccievoice2...@gmail.com" > Date: Tue, 30 Nov 2010 07:49:07 -0600 > To: 'Mritunjay Kumar' , "ccie_voice@onlinestudylist.com" > > Subject: Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone > > Why do you have a different tech prefix for VIA zone? I don’t believe you > need a tech prefix at all for a VIA zone / CUBE. Just have your dial-peers > configured to receive what CUCM is sending. > > > > Also, make sure that you have your “allow connections” commands. Do a show > gatekeeper endpoints and CUBE should be registered as “H323-GW”. If not, > make sure those commands are present and/or bounce the gateway command. > > > > Please post the debug gatekeeper main 10 output as well as show gatekeeper > end. > > > > Jeff > > > > *From:* ccie_voice-boun...@onlinestudylist.com [ > mailto:ccie_voice-boun...@onlinestudylist.com] > *On Behalf Of *Mritunjay Kumar > *Sent:* Tuesday, November 30, 2010 3:06 AM > *To:* ccie_voice@onlinestudylist.com > *Subject:* [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone > > > > Hi all , > > I am facing issue in GK and VIA zone > > sh gatek gw > > CUCM is registered to GK using tech-p 1# > CME is registered to DK using tech-p 44# > VIA zone is registered to GK using tech-p 12# > > > sh gatek gw > Prefix: 1#* > Zone CUCM master gateway list: > 14.160.110.15:1720 US_1 > Zone CUBE master gateway list: > 14.160.110.254:1720 MJ-CUBE > > Prefix: 12#* > Zone CUBE master gateway list: > 14.160.110.254:1720 MJ-CUBE > > Prefix: 44#* > Zone CME master gateway list: > 14.160.115.200:1720 MJ-CME > > call from CME to CUCM is working fine > > but call from CUCM to CME is failing. while calling this i am adding > correct tech prefix and removing it in CME > > enabled debug gate main 5 and error is > > *Nov 30 11:01:04.435: //001191430300/001191430300/GK/rassrv_get_addrinfo: > (44#5002) Matched tech-prefix 44# > > > > *assrv_get_addrinfo(44#5002): Viazone gateway selection failed for zone > "CUBE" > . > > > when CME is registered with tech-p 1# , everthing works fine ie call in > both direction > > without introducing VIA zone , everyting works fine ie CME is regiserted > with tech-p 44# > > gatekeeper cofig > > gatekeeper > zone local BR1 cisco.com 14.160.110.129 > zone local CME cisco.com invia CUBE outvia CUBE > zone local CUCM cisco.com invia CUBE outvia CUBE > zone local CUBE cisco.com > zone prefix CUCM 2... > zone prefix CME 5... > gw-type-prefix 1#* > no shutdown > > Is any configmissing ?? > > Regards, > MJ > > > > > > * > <>___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone
On Tue, Nov 30, 2010 at 6:54 PM, Prashant Patel wrote: > Hi MJ, > > Can you please paste output of sh gatek gw and sh gatek end. Also the dial > peers on HQ. > > > Thanks > Prashant > > On Tue, Nov 30, 2010 at 6:05 AM, Mritunjay Kumar wrote: > >> Hi all , >> >> I am facing issue in GK and VIA zone >> >> sh gatek gw >> >> CUCM is registered to GK using tech-p 1# >> CME is registered to DK using tech-p 44# >> VIA zone is registered to GK using tech-p 12# >> >> >> sh gatek gw >> Prefix: 1#* >> Zone CUCM master gateway list: >> 14.160.110.15:1720 US_1 >> Zone CUBE master gateway list: >> 14.160.110.254:1720 MJ-CUBE >> >> Prefix: 12#* >> Zone CUBE master gateway list: >> 14.160.110.254:1720 MJ-CUBE >> >> Prefix: 44#* >> Zone CME master gateway list: >> 14.160.115.200:1720 MJ-CME >> >> call from CME to CUCM is working fine >> >> but call from CUCM to CME is failing. while calling this i am adding >> correct tech prefix and removing it in CME >> >> enabled debug gate main 5 and error is >> >> *Nov 30 11:01:04.435: //001191430300/001191430300/GK/rassrv_get_addrinfo: >> (44#5002) Matched tech-prefix 44# >> >> >> >> *assrv_get_addrinfo(44#5002): Viazone gateway selection failed for zone >> "CUBE" >> . >> >> >> when CME is registered with tech-p 1# , everthing works fine ie call in >> both direction >> >> without introducing VIA zone , everyting works fine ie CME is regiserted >> with tech-p 44# >> >> gatekeeper cofig >> >> gatekeeper >> zone local BR1 cisco.com 14.160.110.129 >> zone local CME cisco.com invia CUBE outvia CUBE >> zone local CUCM cisco.com invia CUBE outvia CUBE >> zone local CUBE cisco.com >> zone prefix CUCM 2... >> zone prefix CME 5... >> gw-type-prefix 1#* >> no shutdown >> >> Is any configmissing ?? >> >> Regards, >> MJ >> >> >> >> >> * >> >> >> ___ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> > ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone
Correct, you do not need to register your CUBE with a tech prefix at all. Matthew Berry Sr. Voice Engineer - CCIE 26721 [cid:E1F2A7B1-98EB-4A5E-861A-C1BB303B86B6]<http://www.cdw.com/content/services/advanced-technology/default.aspx> CDW Advanced Technology Services 7145 Boone Avenue North | Brooklyn Park, MN 55428 Single Number Reach: +1.763.592.5987 matthew.be...@cdw.com<mailto:ben.c...@cdw.com> From: "givemeccievoice2...@gmail.com<mailto:givemeccievoice2...@gmail.com>" mailto:givemeccievoice2...@gmail.com>> Date: Tue, 30 Nov 2010 07:49:07 -0600 To: 'Mritunjay Kumar' mailto:mjs...@gmail.com>>, "ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com>" mailto:ccie_voice@onlinestudylist.com>> Subject: Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone Why do you have a different tech prefix for VIA zone? I don’t believe you need a tech prefix at all for a VIA zone / CUBE. Just have your dial-peers configured to receive what CUCM is sending. Also, make sure that you have your “allow connections” commands. Do a show gatekeeper endpoints and CUBE should be registered as “H323-GW”. If not, make sure those commands are present and/or bounce the gateway command. Please post the debug gatekeeper main 10 output as well as show gatekeeper end. Jeff From: ccie_voice-boun...@onlinestudylist.com<mailto:ccie_voice-boun...@onlinestudylist.com> [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Mritunjay Kumar Sent: Tuesday, November 30, 2010 3:06 AM To: ccie_voice@onlinestudylist.com<mailto:ccie_voice@onlinestudylist.com> Subject: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone Hi all , I am facing issue in GK and VIA zone sh gatek gw CUCM is registered to GK using tech-p 1# CME is registered to DK using tech-p 44# VIA zone is registered to GK using tech-p 12# sh gatek gw Prefix: 1#* Zone CUCM master gateway list: 14.160.110.15:1720<http://14.160.110.15:1720> US_1 Zone CUBE master gateway list: 14.160.110.254:1720<http://14.160.110.254:1720> MJ-CUBE Prefix: 12#* Zone CUBE master gateway list: 14.160.110.254:1720<http://14.160.110.254:1720> MJ-CUBE Prefix: 44#* Zone CME master gateway list: 14.160.115.200:1720<http://14.160.115.200:1720> MJ-CME call from CME to CUCM is working fine but call from CUCM to CME is failing. while calling this i am adding correct tech prefix and removing it in CME enabled debug gate main 5 and error is *Nov 30 11:01:04.435: //001191430300/001191430300/GK/rassrv_get_addrinfo: (44#5002) Matched tech-prefix 44# assrv_get_addrinfo(44#5002): Viazone gateway selection failed for zone "CUBE" . when CME is registered with tech-p 1# , everthing works fine ie call in both direction without introducing VIA zone , everyting works fine ie CME is regiserted with tech-p 44# gatekeeper cofig gatekeeper zone local BR1 cisco.com<http://cisco.com> 14.160.110.129 zone local CME cisco.com<http://cisco.com> invia CUBE outvia CUBE zone local CUCM cisco.com<http://cisco.com> invia CUBE outvia CUBE zone local CUBE cisco.com<http://cisco.com> zone prefix CUCM 2... zone prefix CME 5... gw-type-prefix 1#* no shutdown Is any configmissing ?? Regards, MJ <>___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone
Why do you have a different tech prefix for VIA zone? I don't believe you need a tech prefix at all for a VIA zone / CUBE. Just have your dial-peers configured to receive what CUCM is sending. Also, make sure that you have your "allow connections" commands. Do a show gatekeeper endpoints and CUBE should be registered as "H323-GW". If not, make sure those commands are present and/or bounce the gateway command. Please post the debug gatekeeper main 10 output as well as show gatekeeper end. Jeff From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Mritunjay Kumar Sent: Tuesday, November 30, 2010 3:06 AM To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone Hi all , I am facing issue in GK and VIA zone sh gatek gw CUCM is registered to GK using tech-p 1# CME is registered to DK using tech-p 44# VIA zone is registered to GK using tech-p 12# sh gatek gw Prefix: 1#* Zone CUCM master gateway list: 14.160.110.15:1720 US_1 Zone CUBE master gateway list: 14.160.110.254:1720 MJ-CUBE Prefix: 12#* Zone CUBE master gateway list: 14.160.110.254:1720 MJ-CUBE Prefix: 44#* Zone CME master gateway list: 14.160.115.200:1720 MJ-CME call from CME to CUCM is working fine but call from CUCM to CME is failing. while calling this i am adding correct tech prefix and removing it in CME enabled debug gate main 5 and error is *Nov 30 11:01:04.435: //001191430300/001191430300/GK/rassrv_get_addrinfo: (44#5002) Matched tech-prefix 44# assrv_get_addrinfo(44#5002): Viazone gateway selection failed for zone "CUBE" . when CME is registered with tech-p 1# , everthing works fine ie call in both direction without introducing VIA zone , everyting works fine ie CME is regiserted with tech-p 44# gatekeeper cofig gatekeeper zone local BR1 cisco.com 14.160.110.129 zone local CME cisco.com invia CUBE outvia CUBE zone local CUCM cisco.com invia CUBE outvia CUBE zone local CUBE cisco.com zone prefix CUCM 2... zone prefix CME 5... gw-type-prefix 1#* no shutdown Is any configmissing ?? Regards, MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] call from CUCM to CME : VIA Zone
Hi MJ, Can you please paste output of sh gatek gw and sh gatek end. Also the dial peers on HQ. Thanks Prashant On Tue, Nov 30, 2010 at 6:05 AM, Mritunjay Kumar wrote: > Hi all , > > I am facing issue in GK and VIA zone > > sh gatek gw > > CUCM is registered to GK using tech-p 1# > CME is registered to DK using tech-p 44# > VIA zone is registered to GK using tech-p 12# > > > sh gatek gw > Prefix: 1#* > Zone CUCM master gateway list: > 14.160.110.15:1720 US_1 > Zone CUBE master gateway list: > 14.160.110.254:1720 MJ-CUBE > > Prefix: 12#* > Zone CUBE master gateway list: > 14.160.110.254:1720 MJ-CUBE > > Prefix: 44#* > Zone CME master gateway list: > 14.160.115.200:1720 MJ-CME > > call from CME to CUCM is working fine > > but call from CUCM to CME is failing. while calling this i am adding > correct tech prefix and removing it in CME > > enabled debug gate main 5 and error is > > *Nov 30 11:01:04.435: //001191430300/001191430300/GK/rassrv_get_addrinfo: > (44#5002) Matched tech-prefix 44# > > > > *assrv_get_addrinfo(44#5002): Viazone gateway selection failed for zone > "CUBE" > . > > > when CME is registered with tech-p 1# , everthing works fine ie call in > both direction > > without introducing VIA zone , everyting works fine ie CME is regiserted > with tech-p 44# > > gatekeeper cofig > > gatekeeper > zone local BR1 cisco.com 14.160.110.129 > zone local CME cisco.com invia CUBE outvia CUBE > zone local CUCM cisco.com invia CUBE outvia CUBE > zone local CUBE cisco.com > zone prefix CUCM 2... > zone prefix CME 5... > gw-type-prefix 1#* > no shutdown > > Is any configmissing ?? > > Regards, > MJ > > > > > * > > > ___ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] call from CUCM to CME : VIA Zone
Hi all , I am facing issue in GK and VIA zone sh gatek gw CUCM is registered to GK using tech-p 1# CME is registered to DK using tech-p 44# VIA zone is registered to GK using tech-p 12# sh gatek gw Prefix: 1#* Zone CUCM master gateway list: 14.160.110.15:1720 US_1 Zone CUBE master gateway list: 14.160.110.254:1720 MJ-CUBE Prefix: 12#* Zone CUBE master gateway list: 14.160.110.254:1720 MJ-CUBE Prefix: 44#* Zone CME master gateway list: 14.160.115.200:1720 MJ-CME call from CME to CUCM is working fine but call from CUCM to CME is failing. while calling this i am adding correct tech prefix and removing it in CME enabled debug gate main 5 and error is *Nov 30 11:01:04.435: //001191430300/001191430300/GK/rassrv_get_addrinfo: (44#5002) Matched tech-prefix 44# *assrv_get_addrinfo(44#5002): Viazone gateway selection failed for zone "CUBE" . when CME is registered with tech-p 1# , everthing works fine ie call in both direction without introducing VIA zone , everyting works fine ie CME is regiserted with tech-p 44# gatekeeper cofig gatekeeper zone local BR1 cisco.com 14.160.110.129 zone local CME cisco.com invia CUBE outvia CUBE zone local CUCM cisco.com invia CUBE outvia CUBE zone local CUBE cisco.com zone prefix CUCM 2... zone prefix CME 5... gw-type-prefix 1#* no shutdown Is any configmissing ?? Regards, MJ * ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
