Re: Debian 10.4 blank screen After new install
On Tue 21 Jul 2020 at 22:25:57 (-0500), Edward M Kent wrote: > Hello All, I am an old Nube trying to get set up to use a Beaglebone on > some projects. I thought I had a successful install after a list of tasks > was displayed down the screen's left hand edge. Those "tasks" are the bootable systems being displayed by Grub. > The list went blank and > left a - in the upper left corner. After a 5 second (default) delay, unless you have struck a key, the system boots the first system in the list. > This curser soon disappeared leaving a > blank screen. The mouse cursed did show up but was a bit erratic. If the drive is "spinning rust", you should've heard it chattering as the OS is loaded. It sounds as if the video mode is unsatisfactory. > I > rebooted several times and ended back at the same place. If you press a key during the first 5 seconds, the countdown should stop. Some suggestions to try: c gives you a grub> prompt. e should show the contents of the menu for this line in the list. You can move up and down the list with the arrows. It's even possible that there are entires for Windows lower down the list. > This is on a win10 Dell and I can not get back to win10 because I did not > get the dual boot setup. I'm hesitant to give you specific Grub commands off the cuff, but if you type e at the first item in the list, you can experiment with video modes that might work. Any changes you make in this way only apply to this boot, so it's a safe way to experiment. A suggestion I have seen made here in the past is to remove the line: load_video Another suggestion, that might be completely useless, is to add the word nomodeset to the end of the line that says something like: linux /boot/vmlinuz… … Others here might have better suggestions. Cheers, David.
Debian 10.4 blank screen After new install
Hello, That blank screen means your hardware has not found the way to load your boot partition. Verify your BIOS configuration. Try toggling between UEFI and MBR assuming your bootable device is ok. Le mer. 22 juil. 2020 à 05:20, Edward M Kent a écrit : > Hello All, I am an old Nube trying to get set up to use a Beaglebone on > some projects. I thought I had a successful install after a list of tasks > was displayed down the screen's left hand edge. The list went blank and > left a - in the upper left corner. This curser soon disappeared leaving a > blank screen. The mouse cursed did show up but was a bit erratic. I > rebooted several times and ended back at the same place. > This is on a win10 Dell and I can not get back to win10 because I did not > get the dual boot setup. > Thanks for any advice. > Mick > >
Re: Debian 10.4 blank screen After new install
Glad to hear it! On Wed, 22 Jul 2020 at 12:57, Edward M Kent wrote: > > Thanks Umarzuki, I will take your advice and make a bootable repair disk > tomorrow. Too late tonight. I used f10 on reboot and now have win10. > Mick > > > On Tue, Jul 21, 2020, 10:33 PM Umarzuki Mochlis wrote: >> >> On Wed, 22 Jul 2020 at 11:21, Edward M Kent wrote: >> > >> > Hello All, I am an old Nube trying to get set up to use a Beaglebone on >> > some projects. I thought I had a successful install after a list of tasks >> > was displayed down the screen's left hand edge. The list went blank and >> > left a - in the upper left corner. This curser soon disappeared leaving a >> > blank screen. The mouse cursed did show up but was a bit erratic. I >> > rebooted several times and ended back at the same place. >> > This is on a win10 Dell and I can not get back to win10 because I did not >> > get the dual boot setup. >> > Thanks for any advice. >> > Mick >> > >> >> Hi, >> >> Try Boot-Repair.
Re: Debian 10.4 blank screen After new install
Thanks Umarzuki, I will take your advice and make a bootable repair disk tomorrow. Too late tonight. I used f10 on reboot and now have win10. Mick On Tue, Jul 21, 2020, 10:33 PM Umarzuki Mochlis wrote: > On Wed, 22 Jul 2020 at 11:21, Edward M Kent wrote: > > > > Hello All, I am an old Nube trying to get set up to use a Beaglebone > on some projects. I thought I had a successful install after a list of > tasks was displayed down the screen's left hand edge. The list went blank > and left a - in the upper left corner. This curser soon disappeared > leaving a blank screen. The mouse cursed did show up but was a bit > erratic. I rebooted several times and ended back at the same place. > > This is on a win10 Dell and I can not get back to win10 because I did > not get the dual boot setup. > > Thanks for any advice. > > Mick > > > > Hi, > > Try Boot-Repair. >
Re: Debian 10.4 blank screen After new install
On Wed, 22 Jul 2020 at 11:21, Edward M Kent wrote: > > Hello All, I am an old Nube trying to get set up to use a Beaglebone on > some projects. I thought I had a successful install after a list of tasks > was displayed down the screen's left hand edge. The list went blank and left > a - in the upper left corner. This curser soon disappeared leaving a blank > screen. The mouse cursed did show up but was a bit erratic. I rebooted > several times and ended back at the same place. > This is on a win10 Dell and I can not get back to win10 because I did not get > the dual boot setup. > Thanks for any advice. > Mick > Hi, Try Boot-Repair.
Debian 10.4 blank screen After new install
Hello All, I am an old Nube trying to get set up to use a Beaglebone on some projects. I thought I had a successful install after a list of tasks was displayed down the screen's left hand edge. The list went blank and left a - in the upper left corner. This curser soon disappeared leaving a blank screen. The mouse cursed did show up but was a bit erratic. I rebooted several times and ended back at the same place. This is on a win10 Dell and I can not get back to win10 because I did not get the dual boot setup. Thanks for any advice. Mick
