Re: [Elecraft] WTB K3-K3S 200hz Or 250hz Filter.
>Looking For 200hz Or 250hz Filter For K3-K3S. > >Ray WD4X Inrad sells them. They made the OEM filters. https://www.inrad.net/home.php?cat=140 Gary NA6O __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Diversity
More rigs with diversity reception: FTdx101 Ts-990s Icom 7610 …Just about every dual-rx radio does it. Gary NA6O __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] KPA1500 front panel locked
Helping a friend connect his KPA1500 to a K3. The AUXBUS is working, following the radio etc. like normal. However, as soon as that cable is plugged into the KPA, it’s front panel buttons all cease to function. Remote control via USB or ethernet work fine. The AUXBUS cable is a proper one, not a VGA cable. I’ve never seen this before and can’t find any reference to a locked front panel. Gary NA6O __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 drive level for Q5 Signal 432 Transverter
Sounds like you should do the low-level power calibration using the K3 Utility. For now, you can increase the maximum, up to 1.5 mW, and presumably get the desired output. Gary NA6O > Using the Config Menu, I have set the drive level at the maximum for the > transverter at 1 MW. However, when I check the drive from the front panel > PWR knob it reads 0.8MW and I cannot adjust it any higher with the knob. > Nothing I do seems to change the the PWR knob drive level. I am running SSB > on 432.095. > > Any suggestions would be most appreciated. > > Tnx es 73, > > NS4V __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 Frequency Calibration
Not sure why nobody has mentioned using WSJT in frequency calibration mode. It’s the bottom selection in the Mode menu. Shows your offset in Hz to about 5 decimal places. Just pick from the list of standard freqs and away it goes. Then adjust the K3 ref frequency to walk it in. There are even guys doing long-term observations on Allen variance this way. Gary Johnson NA6O g...@me.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com