Re: [Elecraft] P3 Failure, and question
My P3 does the same thing. If i keep cycling power it eventually comes on and works. I suspect there is a bad capacitor in the LCD backlight power. I have not actually looking into it yet. -- "If you are not the lead dog, the scenary never changes" Rick Stanback N4WCQ On Mon, 2021-04-12 at 04:41 -0700, Dave Cole wrote: > A bit more data: > > 1. The (3 utility can talk to it. > 2. If I try and capture an image, it goes through the motions, but > no > image is captured. > 3. It accepts commands via a keyboard. > 4. A load from the last config file did not correct things. > 5. A full power off and on did not correct things. > > 73, and thanks, > Dave (NK7Z) > https://www.nk7z.net > ARRL Volunteer Examiner > ARRL Technical Specialist, RFI > ARRL Asst. Director, NW Division, Technical Resources > > On 4/12/21 4:27 AM, Dave Cole wrote: > > Hello, > > > > My P3 seems to have had a display failure. The SVGA is working, as > > I > > can control the K3 via macros fired at it via the keyboard input. > > It > > failed to light off once before, but that seemed a one off thing, > > not it > > seems permanent. > > > > Has anyone seen this before? If so, what was the cause? > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to r...@tripletry.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KPA500
My new KPA500 has started acting up again. It was coming up with Invalid in the display and no high voltage. I checked the aux cables and re-seated them and that seems to have cured the invalid error but I still get no high voltage. It was doing this after I first built the kit and then it just seemed to get over it and was working fine for about a week. Any ideas on what to check the manual does not really give you much to go on. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Noise Power Ratio and the K3 with new synthesizer?
I just completed the build of my KAT500 and KPA500 and I had the following issues. The KAT500: the software was very flaky trying to connect to the KAT. I run Fedora 21 so it might be the bleeding edge Linux. I did finally get the connect and hit the optimize for KPA500 button. I am still not able to hit the tune button on the KAT500 and get the K3 to xmit and tune. If I hit the button and then hit the tune button manually on the K3 it tunes? KPA500: When I first powered up the display would say KPA500 for a bit then Invalid?? Then if I put the amp to oper it would immediately get the 270v fault. I took it apart and inspected all the connections including the ribbon cables and although I did not find anything out of place or not seated when I put it back together it seems to just work? I have made a few contacts and everything seems to be OK. The amp follows the K3 band with no problems. -- Rick Stanback (N4WCQ) Chance only favors the prepared mind. Louis Pasteur On Thu, 2015-03-12 at 14:08 -0400, Scott Manthe wrote: I suspect that the Noise Power Ratio test was used because that is the only test that Adam could use to get his beloved Icom gear near the top of the list. Mr. Farson has had a website devoted to Icom gear for many years, so I'm not sure if this test could be considered even remotely objective. Here is a NPR tutorial from another source, for those interested and technically proficient enough to investigate further. 73, Scott, N9AA On 3/12/15 10:53 AM, Chip Stratton wrote: Adam Farson VA7OJ has an article in the current March/April 2015 QEX discussing the use of Noise Power Ratio (NPR) to help define a receiver's performance in a crowded band in a way that might be more illuminating than the simpler two tone tests. Its an interesting discussion which makes some sense, but then I'm not anywhere close to an expert in that field. In any event, he has figures from a number of transceivers, including a couple of K3s which no doubt do not have the new synthesizer. The K3s still performed very well relative the the rest of the field in these tests, though they were slightly behind the IC-7700, IC-7800, and TS-590S. Which of course makes me wonder how the K3 with new synthesizer would perform in this arena? From a guy with a mild metrology addiction... Chip AE5KA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to r...@tripletry.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] linux K3 utility
It would sure be nice to have the sources so we could build the binaries for 64bit. On Wed, 2014-05-21 at 15:16 -0400, David Sanders W4DES wrote:7 3, David W4DES On May 21, 2014, at 1:45 PM, Doug Person via Elecraft elecraft@mailman.qth.net wrote: Once again, I'm confused. I've had no luck getting the Windows K3 utility to make the K3 transmit in terminal mode. So, I thought I would try the linux utility. I downloaded it to my linux mint 16 computer, unpacked it in my home directory, verified that the execute bit was on, double clicked on it - and - nothing. I opened a terminal in the directory and entered ./k3util and got no such file or directory from bash. Huh? I can see it, the permissions are correct, it is executable... What am I doing wrong? Doug -- K0DXV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to w4...@sandersweb.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to r...@tripletry.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com