Re: [Elecraft] K3 ANT1 / ANT2 switching

[William Lagerberg]

Hi there Tim,

I have the same problem, I did some thinks at the back site changing the 2 
meter antenna, I think I touch the 12 volt power supple and then the K3 went to 
the same as you describe. When I press the ANT button with the AUTO ATU in 
Bypass, there's a click, and the annunciation changes from ANT1 to ANT2, but I 
can still hear signals just as loud, even though there a dummy load on ANT2. 
Also If I transmit, it doesn't matter whether I have ANT1 or ANT2 selected, RF 
always comes out of ANT1 socket. If I have the ATU activated, the symptoms are 
exactly the same.  What was your solution ??  I think it's in the software, but 
where as far as I know it only went of.. and I turned it on again which I doe 
every day.

Regards William


PE1BSB @ zendamateur.nu
Stommeerkade 65
1431EL  Aalsmeer


-Original Message-
From: elecraft-boun...@mailman.qth.net  On 
Behalf Of Tim Raven via Elecraft
Sent: Saturday, 10 July 2021 13:37
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 ANT1 / ANT2 switching

Hi, 

 

I have acquired a second-hand K3/100 with the Auto ATU and 2nd receiver, which 
I have been checking out, calibrating and installing extra filters.
Everything has worked exactly as expected, until I tried to use an antenna 
connected to ANT2 socket. 

 

I have a fan dipole connected to ANT1, and a 50 Ohm dummy load to ANT2. When I 
press the ANT button with the AUTO ATU in Bypass, there's a click, and the 
annunciation changes from ANT1 to ANT2, but I can still hear signals just as 
loud, even though there a dummy load on ANT2. Also If I transmit, it doesn't 
matter whether I have ANT1 or ANT2 selected, RF always comes out of ANT1 
socket. If I have the ATU activated, the symptoms are exactly the same,
except when I switch from ANT1 to ANT2 there's no click.   

 

The Auto ATU works fine, and I have the KRX3 "ANT=bnc" set. 

 

I can also hear stations on the 2nd receiver through the  ANT1 socket or via 
AUX antenna socket. 

 

The firmware has been updated to the latest versions for MCU, FPF, and both DSP 
units.

 

Any help would be most welcome.

 

73 de Tim G4ARI 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message 
delivered to pe1...@zendamateur.nu 


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] old K2 and K3 and P3 case

[William Lagerberg]

Hello list and every body els.

I had a fire in my house it started in my shack, i told earlier, all my 
equipment is gone, i managed to get the prints of the K2 K3 and P3 pretty clean.

I need 3 new cases  i know i can order them and contact are running and very 
very promising, but the best thing i can do is just get some old not working K2 
K3 P3 stuff. Lighting, reverse polarity i don't mint i want the cases.. and 
perhaps some parts.

Is there some body on this planet who can help me :-))

I live in Holland (the Netherlands) and off course will pay for the units.  So 
please let me know .

i rather keep this off list because this is going to generate lots and lots off 
traffic all those people with old stuff :-))

My mail address is pe1...@zendamateur.nu.

Thanks in advance for the space this is taking

regards William

--
Pe1bsb
William lagerberg
Stommeerkade 65
1431 EL  Aalsmeer

E  pe1...@zendamateur.nl
 
--





This email may contain confidential and privileged material for the sole use of 
the intended
recepient. Any review or distribution by others is strictly prohibited.
--

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Follow up shack / house burn

[William Lagerberg]

Dear Radio Friends,

First I am dutch and perhaps my English is not as good as it should be, sorry 
for that.

It has been 5 almost 6 weeks after the fire with destroyed our house for 50% it 
started in my shack. We am stil inventorying our house for the insurance. I 
good send fotos, but don’t know how, the server don’t want that :-)

At first let me give all of you some advice, please take a digital camera and 
walk trough your house and make from everything pictures, all stuf if it is in 
a cabinet or in a drawer, downstairs upstairs or on the 2e floor just do it. It 
saves you a lot of time. When something goos wrong like a fire or so. We really 
lost a hole cabinets which all our papers invoices etc, a cabinet of 2 meters 
high 1,20 wide it is just gone with everything in it.

I even did hear somebody who has inventory listsof everything. But 
thats for you to decide..

My question is, everything is burned some things only on the outside my 736 is 
just gone but the 50 Mhz and the 1296 module looks ok, my R5000 is a goner but 
the filters are ok,

I took my K1 K2 K3 and P3 totally apart an whith a sonic-cleaner with special 
stuf ( from the guys who are helping us) I cleaned every part of them.
I think I managed to save a lot of electronics the prints look like new. but 
all the cabinets and buttons are gone, from the K3 the daling knob is melted, 
really and the prints look fine. My KX3 seem to have survived it it was in a 
aluminium box. 

So I am looking for somebody who has the opposite per haps a lightning strike 
or so and all electronics gone but the cabinets ok.

If there is somebody who can help me I would be very glad. I am looking for K2 
K2 Tuner and K3 and P3 housing.

In the last stage I am going to ask Elecraft to help me., but I thought first 
try this.

Regards everybody PE1BSB


--
Pe1bsb
William lagerberg
Stommeerkade 65
1431 EL  Aalsmeer

E  pe1...@zendamateur.nu
 K1, K2, K3, P3, KX3 now working with a Icom 7300 with has been 3 days below 
50cm of water get it out cleaned it let it dry for 2 weeks put a new display in 
it and it was working  :-)
--

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Fire in the house li-ion

[William Lagerberg]

Guys,

I want to give you a advice, my shack it (was) in the basement (cellar??) I do 
all my thing for the hobby there.
A collega of mine asked me to take a look at two Go-Pro LI-Ion accu's because 
they where not loading anymore.

So I put the first one on the loader for 8 till 9 hours and checked it and it 
was ok  ( with 10% loading current)
Then I dit put the second one in same place at 10 in the morning at 3 my 
daughter called me there is a fire.
We rusted to the cellar but I could not enter it was filled with dark smoke.

My shack is gone and 90 % off my house, I have insurance don’t now if it is 
enough to cover all of my Elecraft stuff

My K1, my own build K2 my K3  and my KX3 are gone, I found my K1 in 20 cm off 
water really down under, I clean’t it with fresh water.
After that flushed it with pure alcohol. It is completely taken apart today as 
far as is possible.
I Hope it will survive I will let it dry for a lot of day’s

My K2 is melted the same as my P3 and my K3 perhaps I can order the outside of 
both, but a am still not allowed to enter the basement so I don’t know how it 
looks at the inside.

So finale the message is please take care with li-ion accuse battery’s. It did 
cost me our house in 1 hour.

http://www.nhnieuws.nl/nieuws/206119/bewoner-vlucht-met-dieren-pand-uit-vanwege-grote-brand
 


Regards William Pe1bsb
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K2 (K60XV)

[William Lagerberg]

Dear list,

Is there anybody who has a left over K2 60m (K60XV) print laying somewhere 
around and not doing anything with it.

I like to take it over..

Regards William


--
Pe1bsb
William lagerberg
Stommeerkade 65
1431 EL  Aalsmeer

E  pe1...@zendamateur.nl
 
--





This email may contain confidential and privileged material for the sole use of 
the intended
recepient. Any review or distribution by others is strictly prohibited.
--

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] 60 m and Low Level Transverter Interface (K60XV)

[William Lagerberg]

Hi list,

I do have an K2 transceiver, and i love it build it for 90% by my self and it 
works ok.
After getting the DSP print last month, the last thing i am looking for is an 
(i would like still to be build) K60XV.

The adventage is not only 60 meters but also the transverter in/output.

Is there somebody who does not need it anymore, or think’s that William is such 
a nice guy he can have it, i would like that very much.

I live in Holland, so that good be a small issue but the package is not big. so 
it good go in a big envelop.

Regards William PE1BSB




__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] OT:. G5RV's

[William Lagerberg]

And you now dear list users, i have a G5RV and i really love it it works 
allways, and give’s me good results :-))

Just have to say that.

Regards William PE1BSB



> On 05 Aug 2016, at 16:58, Phil Wheeler  wrote:
> 
> Alas, the poor G5RV.  Now that its been flogged to death, maybe we need a new 
> target -- say the Windom?
> 
> Phil W7OX
> 
> On 8/4/16 10:22 PM, Wes Stewart wrote:
>> The tuner loss also depends on how it is adjusted. For example the very 
>> popular high-pass Tee with three adjustable elements has an infinite number 
>> of possible combinations that will effect a match on the same load Z.  One 
>> of them is the lowest loss solution, all of the others aren't.
>> 
>> As I said earlier, in a letter to Dean Straw dated February 2, 1994 I 
>> offered an example where the SPC tuner, then current in the handbooks, could 
>> be used to match an impedance of 4.34 +j46 to 50 ohm. (I forget where this 
>> came from but it was a real possibility)  I assumed Qc = 1000 and Ql = 300 
>> (generous). I used Touchstone to calculate the minimum loss and maximum loss 
>> solutions The best case was 1.6 dB and the worst case was 7.8 dB.
>> 
>> With lower Q components, Qc = 500, Ql =200, the losses were 2.4 to 9.5 dB!
>> 
>> Wes  N7WS
>> 
>> 
>> On 8/4/2016 2:00 PM, Alan Bloom wrote:
>>> > It's a pity that too many newcomers, as well as many oldsters, are
>>> > enamored by this piece of wire.
>>> 
>>> The G4RV is definitely a compromise antenna.  However its advantage is that 
>>> is has low-enough SWR to be easily matched by most tuners on a number of 
>>> bands.
>>> 
>>> > ... the horrific losses that could be incurred even
>>> > with high quality tuners,
>>> 
>>> It's true that tuner losses are the manufacturers' dirty little secret. 
>>> Loss is rarely specified, partly because it can be pretty bad, and partly 
>>> because it is hard to measure, but also because it is not constant - it 
>>> depends on the particular impedance being matched.
>>> 
>>> One exception is the old Drake tuners.  Their Pi-L topology makes the loss 
>>> almost independent of the load impedance.  If you can get it to match, you 
>>> know that almost all the power is going into the feed line. For example, 
>>> the MN-2700 that I designed when I was at Drake was specified at 0.5 dB 
>>> maximum insertion loss and I did a lot of testing and tweaking to achieve 
>>> that on all bands.
>>> 
>>> Alan N1AL
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to pe1...@zendamateur.nl


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] P3 wireles keyboard

[William Lagerberg]

Hi Group,

I think there has been told a lot about wireless keyboard an Kpod etc etc.

But Is it possible to get a wireless keyboard connected to the P3 somewhere i 
read that a 2.4 Ghz remote keyboard would work ???

Is there somebody who has experience, I have many apple keyboard but every 
where i read, they don’t work, i did not even try :-)

is the a list of keyboards ??

I am getting stuck in the wire every time ( just google my call) you understand 
:-)

Regards William PE1BSB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] New second hand P3 question

[William Lagerberg]

Hi Group,

I have a P3 connected with VGA and TXmon to my K3.

Before this P3 i used a SDR-IQ connected to a computer and if-out to the 
SDR-IQ, because of the computer noise and the slow starting of windows etc etc, 
i wanted a P3 this is now perfect.

It works nice, but my waterfall display is very unclear it not like i was used 
to, is there a way to change that ???
It’s unclear on the P3 and on the VGA monitor which is 21” so it should be ok.

Next to that is it so that i was used to when i turn my dial of my K3 that the 
display changes immediately (i was able to tune in to a station with the 
display) with the P3 there is really a noticeable time between turning and 
moving of the display.  Is this normal or should i change some settings in the 
P3 or the K3.

All software is the latest of elecraft.

William Pe1bsb



--
Pe1bsb
William lagerberg
Stommeerkade 65
1431 EL  Aalsmeer

E  will...@zendamateur.nl

—---




This email may contain confidential and privileged material for the sole use of 
the intended
recepient. Any review or distribution by others is strictly prohibited.
--

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3 transverter question

[William Lagerberg]

Dear fellow Elecraft users,

I have build a 70 Mhz transverter, i have read the K3 manual about how to 
connect a transverter.

I have in my K3 the build in 2 meter transverter, and i do understand that the 
144 Mhz transverter, also uses 28-30 Mhz.

What is the best way to solve this, 

I have seen that Elecrafts own transverters, can be daisy chained. Can i build 
that into my own transverters ?? I like to have the possibility to connect more 
transverters then this one.

Is there more documentation available and where can i find that.

I o have the building transverter option in my K3 KXV3A or B i don't now i have 
the latest one still have to be build in.

Thanks all ready for all your advices.

William PE3BSB

K2, K3, KX3
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Building K2 SSB unit KSB2 version E

[William Lagerberg]

Thanks Don,

I reversed the connectors, female = female and male = male now.
 
For everybody when you desolder the connectors used in the K2 for the SSB board 
for example, the pins are getting lose in the plastic by the mail connectors, 
take care that they get the same hight when u use them again….
My advice remove them and take new one’s its not the money :-))

Regards William PE1BSB



> On 24 Apr 2016, at 20:09, Don Wilhelm  wrote:
> 
> William,
> 
> I hate it when a builder does that and then I have to repair it later in its 
> life - only because the bypass jumpers I have should I need to remove the 
> KSB2 for test purposes do not work.
> 
> Other than that aspect, it will cause no operational problems.
> There is a greater chance of the male pins to become bent if they are on the 
> RF board, and if they should, they are harder to straighten than male pins on 
> the option board.
> 
> If you have *good* desoldering equipment available, I would change them, but 
> lacking that, leave them as-is.
> 
> 73,
> Don W3FPR
> 
> On 4/24/2016 12:36 PM, will...@zendamateur.nl wrote:
>> Hi every body,
>> 
>>  
>> Posted some messages, and love the way the list works.
>> 
>> Sorry about my English last message was just thinking on paper and that
>> ended in some comments :)
>> 
>>  
>> I bought the K2 ¼ already build, looked good so I took the risk…
>> 
>>  
>> Now wat I noticed having finished today the RF board, is that the previous
>> builder reversed the connectors J9 J10 and J11 he installed the mail side on
>> the RF board, and the female on the KSB2 board.
>> 
>>  
>> I don’t think there will be a divergence.
>> 
>> 
> 


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] New Elecraft Product: K-Pod Control Panel for K3S and K3 Transceivers

[William Lagerberg]

Hi Wayne,

Sound’s good to me, but with a wire connected to K3 or K3S  wasn’t there a 
possibility to make a small bluetooth module into K3 and K3S then there would’t 
have been a possibility to do it wireless…
Next to that, you probably would have the possibility to connect other devices 
to ??

I am not a programmer, so perhaps it is program technical not possible, but i 
think that would have been very nice perhaps better….

Then you can put it where you like on your desk.

My little attribute on this subject,   William PE1BSB.


> On 14 Apr 2016, at 05:04, Wayne Burdick  wrote:
> 
> Hi all,
> 
> We've had many requests for a small control panel (or pod) as an extension to 
> the K3 and K3S transceivers. We finally got around to it! 
> 
> Our new K-Pod is a very compact unit, featuring a precision tuning knob, VFO 
> A/B/offset rocker switch, and 8 programmable tactile-feedback switches. 
> Switch feedback is provided by activation messages on the radio's LCD, as 
> well as the pod's own 4 indicator LEDs and audio tone generator. This 
> multi-modal information can help maximize operating efficiency and reduce 
> fatigue during extended operating periods.
> 
> Typically the K-Pod would be placed next to a computer keyboard, allowing the 
> operator to quickly QSY, clear RIT, enter diversity mode, change menu 
> settings, etc., without that long stretch to reach the radio's front panel. 
> 
> But the K-Pod's flexible interface goes beyond substitution of the radio's 
> knobs and switches. In effect, you can design your own customized controls 
> for the radio.
> 
> Each of the 8 programmable switches has tap and hold functions. When a switch 
> function is used, it activates one of up to 16 user-defined command sequences 
> that are actually stored in the radio itself, as macros. A single macro can 
> accomplish many tasks at once, such as setting up custom splits, configuring 
> the receiver or subreceiver for specific situations, sending transmit 
> messages at differing code speeds, etc. Macros can be easily created or 
> edited using K3 Utility, which runs on PC, Mac, or Linux platforms.
> 
> The K-Pod has the following features:
> 
> * high-quality weighted, soft-touch tuning knob--same as used on the K3S
> * same 400-count, ball-bearing optical encoder used in the K3 and K3S
> * adjustable knob friction
> * 3-position rocker switch to assign the knob to VFO A, VFO B, or RIT/XIT
> * 8 programmable function switches, each with tap/hold functions
> * simple switch programming using K3 Utility (many examples in K-Pod manual)
> * four user-definable LEDs (three of them show knob assignment by default)
> * audio tone generator for switch feedback (can be easily turned off)
> * USB port for firmware loading and future equipment/computer control 
> applications
> * simple connection to K3 or K3S--uses the 6-pin RJ-style jack beneath the 
> front panel
> * flexible power source: rear 12-V jack on the radio, DC barrel jack, 
>  USB port, or even through the 6-pin data cable, with minor radio modification
>  (the latter method results in a single cable to the K-Pod for data and power)
> * 3 utility outputs for miscellaneous equipment control applications 
>  (outputs provide a low resistance to ground when turned on, usable with 
> relays, etc.)
> 
> The K-Pod's all-steel enclosure weighs a full pound for excellent stability, 
> yet measures only about 3.5 x 3 x 1 inches. A highly stable folding tilt 
> stand is included to angle the panel for optimal access. There's also a 
> 2-hole RAM mount pattern on the bottom for easy attachment to any surface.
> 
> For photos and further information, please visit our K-Pod web page:
> 
>  http://www.elecraft.com/k-pod/k-pod.htm
> 
> 73,
> Wayne, N6KR
> Eric, WA6HHQ
> 
> 
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to pe1...@zendamateur.nl


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] K3XREF

[William Lagerberg]

Hi there all,

I am looking for a  K3EXREF who has bought one and does not use it and is 
willing to sell..

Regards PE1BSB  Netherlands



--
Pe1bsb
William lagerberg
Stommeerkade 65
1431 EL  Aalsmeer

E  will...@zendamateur.nl
 
--




This email may contain confidential and privileged material for the sole use of 
the intended
recepient. Any review or distribution by others is strictly prohibited.
--

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Elecraft SP3 External Speaker details

[William Lagerberg PE1BSB]

Hi all,

I like the Speaker its looks far better then the SP8 from Yaesu i am using 
now….., it’s for what it is a little bit expensive including tax and transport 
to get it to holland, it will be i think around 260 dollars, but i assume the 
quality wil make that right. And when the USB interface for the K3 is available 
it’s two for one freight costs.

But my comments:

First I would have liked a 3,5 mm headphone plug at the front. Some body 
mentioned it and it is really a good idea.  

Next i have seen on question about room in the case for a power supply, i do 
really like to investigate if it is possible to put a 25 / 30A power supply 
into that empty housing. Perhaps even the one that Elecraft comments and sells 
on it’s site SS30DV.


Is it possible somebody send a picture of the unit open.. perhaps the guys at 
Elecraft…



--
Pe1bsb
William lagerberg

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Upgrades for the K3

[William Lagerberg]

I think it’s here :

http://www.elecraft.com/order_form_parts.htm#K3%20Parts

William Pe1bsb




 On 29 Jul 2015, at 16:08, Nr4c n...@widomaker.com wrote:
 
 Check the FAQ, Jack!
 
 Web site, top of page is a FAQ on the new K3S.  I believe it has info on this.
 
 Sent from my iPad
 
 ...bc  nr4c
 
 On Jul 28, 2015, at 6:50 PM, Joe W2KJ w...@bellsouth.net wrote:
 
 Howdy Gang:
 
 Is there info on the Elecraft website that describes what new boards will be 
 available for the K3 to make it almost a K3S, i.e., new synthesizer, new 
 audio/DSP board, etc, etc.
 
 I skimmed over the website but must have missed the info.
 
 Many thanks for any assistance.
 !
   73, Joe W2KJ
   I QRP, therefore I am
 
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to n...@widomaker.com
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to pe1...@zendamateur.nl

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] [K3] 2 meter module

[William Lagerberg]

Hi there group,

I am all ready member of the KX3 yahoo group, but regarding the fact that i do 
have also a K3, i became member here to.

I do have 2 small questions:

1) is about the fact that on 2 meters you can dial within a 5 10 12,5 etc ( 
don't remember how you call it) but my problem is that several times that when 
i go to dial over the band in fm with 12,5 it doesn’t start at for instance 
145.000 and then go little steps 12,5 up.
No it does for instance when i switch it on 144.995 it is going to make steps 
from there and goos 12,5 up zo 145.0025 etc that is not handy :-))

2) and perhaps it is related, it seems that my frequency is 5 kHz of the right 
frequency ( i only tested receiving by the way) what is the best way to check 
and, i am pretty sure it is, how can i fix it…

William Pe1bsb the Netherlands 


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com