Re: [Elecraft] CONFIG Question
The uC 04.86 FW REVS is the firmware revision number. From this screen the VFO B knob should cycle through the config parameters and the VFO A knob will cycle through the values available for the selected parameter. From the FW REVS screen, if rotate the VFO A knob clockwise a little, it should change to something like d1 02.83 which is the DSP firmware revision. I am curious if it will do this, but not change the frequency when you exit the menu. Mike KI0HA On 9/19/2014 11:00 PM, Ron Wetjen wrote: When I go into CONFIG the display reads uC 04.86 FW REV5 Turning VFO B doesn't change the display (and turning VFO A doesn't change the frequency). Checked to make sure the VFO LOCK wasn't engaged ... they weren't. The knobs and buttons all seem to be working. Thoughts on what to check? Ron, WD4AHZ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] CONFIG Question
On 9/20/2014 4:24 AM, Michael Eberle wrote: From the FW REVS screen, if rotate the VFO A knob clockwise a little, it should change to something like d1 02.83 which is the DSP firmware revision. I am curious if it will do this, but not change the frequency when you exit the menu. No, turning either VFO A or VFO B doesn't change anything when in CONFIG mode. Will try to take a look at the encoders later today and double check to see that they are installed correctly. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] CONFIG Question
On 9/20/2014 8:36 AM, Ron Wetjen wrote: Will try to take a look at the encoders later today and double check to see that they are installed correctly. Disassembled the front panel ... and reinstalled the encoders. That corrected the problem. Both VFO's are working now. On to the setup! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] CONFIG Question
Finished building my brand new K3 earlier today and am now at the Test and Calibration point in the manual. Radio powers up OK. When I go into CONFIG the display reads uC 04.86 FW REV5 Turning VFO B doesn't change the display (and turning VFO A doesn't change the frequency). Checked to make sure the VFO LOCK wasn't engaged ... they weren't. The knobs and buttons all seem to be working. Thoughts on what to check? Ron, WD4AHZ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
