Re: [Elecraft] PX3 Impressions
On 10/25/14 at 1:27 PM, k...@comcast.net (Jan) wrote: *Received the PX3 on the 9th ~ assembly was straight forward with a little assistance from tech-support**. OOPS, I placed the bezel on the wrong-side of the front panel = end-plate doesn't fit well that way. :-) I did that too. After I had corrected the error and finished assembly, I then down loaded the manual errata sheet which had warnings not to install the bezel on the inside. :-) Note that the errata sheet is dated October 17, 2014 which is about the time my PX3 shipped. The PX3 is up and running now, but the serial number, 555, makes me think I have a timer chip HIHI. I join Jim Brown in wanting fixed track mode. It is a lot harder to tune to a signal on the waterfall on the PX3 than it is on the P3 in fixed track, since you can't see where you are in the waterfall as you tune. If the waterfall panned as you tune, it might be easier. Marker A is the best way I have found, but it adds an extra step of complexity in tuning. On the P3, I have it set up so when I switch to a WARC band (or 160 meters), I have the whole band displayed on the waterfall. It is nice to have band at a glance information about signals a few seconds after switching. 73 Bill AE6JV --- Bill Frantz| Concurrency is hard. 12 out | Periwinkle (408)356-8506 | 10 programmers get it wrong. | 16345 Englewood Ave www.pwpconsult.com |- Jeff Frantz | Los Gatos, CA 95032 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] PX3 Impressions
On 10/26/2014 12:32 AM, Bill Frantz wrote: *Received the PX3 on the 9th ~ assembly was straight forward with a little assistance from tech-support**. OOPS, I placed the bezel on the wrong-side of the front panel = end-plate doesn't fit well that way. :-) I did that too. After I had corrected the error and finished assembly, I then down loaded the manual errata sheet which had warnings not to install the bezel on the inside. I made the same mistake. 73, Jim K9YC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] PX3 Impressions
*Received the PX3 on the 9th ~ assembly was straight forward with a little
assistance from tech-support**. OOPS, I placed the bezel on the wrong-side
of the front panel = end-plate doesn't fit well that way. :-)
*/Impressions: Assembly was easy, makes for an octopus hookup with
all the interface cables ~ and it works satisfactory. Hope a /SVGA / FFT
http://www.elecraft.com/elecraft_prod_list.htm#p3
Adapter Card http://www.elecraft.com/elecraft_prod_list.htm#p3 /**{not
available yet} for the PX3 will improve my acceptance
~ awaiting for it patiently ~
/
//Cheers, Jan K1ND ~ now 60 years in the hobby ~
/
PS: Desire the larger monitor option; have been using a 21 one with my
Genesis G59 MKIII sdr-transceiver kit ~ for more than two years now.
/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com
