Re: problem with MySon Ethernet Nics
Hello Olaf Hoyer and list, i want to thank you for your help. I have resolved this problem. I also succeed to move server from Redhat box to freeBSD too. Good luck to you www.airland.kiev.ua - Airland Network eMail ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: problem with MySon Ethernet Nics
It is driver for MySon Ethernet Nics and it is in :/usr/src/sys/dev/my, compiled it into kernel, that is all. Note: before compiling it into kernel, under file GENERIC (or modified file of GENERIC) finding the division of NIC and add : device my rebuild the kernel now :) - Ni dung gc Gi t: Olaf Hoyer [EMAIL PROTECTED] Gi n: GiTi [EMAIL PROTECTED] ng gi: [EMAIL PROTECTED], Olaf Hoyer [EMAIL PROTECTED] Ch : Re: problem with MySon Ethernet Nics Ng y: Mon 22/03/2004 19:21 On Mon, 22 Mar 2004, GiTi wrote: Hello Olaf Hoyer and list, i want to thank you for your help. I have resolved this problem. I also succeed to move server from Redhat box to freeBSD too. Hi! well, just for the archives, what did you do? I looked around the driver source, for identifying the chipset, as it seems a realtek in disguise, but am a bit busy at work right now... cu Olaf www.airland.kiev.ua - Airland Network eMail ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: problem with MySon Ethernet Nics
Olaf Hoyer wrote:
Well, do you mean with compiled its driver that they provide some own
driver?
yes, my Nic has own driver but ... only for Freebsd 2.x and 3.x. And this is
its instruction
begin-
Installation:
1. copy the source codes if_fet.c and if_fetreg.h to /sys/pci directory,
#cp if_fet.c /sys/pci
#cp if_fetreg.h /sys/pci
2. modify /sys/conf/files, add the following line
pci/if_fet.c optional fet device-driver
3. modify /usr/src/sys/i386/conf/GENERIC, add the following line
device fet0
4. compile the kernel,
#cd /usr/src/sys/i386/conf
#cp GENERIC MYKERNEL
#/usr/sbin/config MYKERNEL
#cd /usr/src/sys/compile/MYKERNEL
#make depend
#make
#make install
5. reboot the system,
#reboot
6. bind your card to an IP address
#ifconfig fet0 ${IPADDR} broadcast ${BROADCAST} netmask ${NETMASK}
7. now, you should be able to ping local network.
--end---
Ok, in order to be able to help you, we need at least a dmesg with the
card, and the _exact_ message, and also a pciconf -lv will be helpful.
Because of rebranding of network chips one can never be sure what
chip-revision you get with those relabelled products.
Please boot a kernel.GENERIC and post that dmesg.
thank you, Olaf Hoyer
this is my dmesg.today:
begin-
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-RELEASE #0: Sun Jan 11 04:21:45 GMT 2004
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel /boot/kernel/kernel at 0xc0a33000.
Preloaded elf module /boot/kernel/acpi.ko at 0xc0a3326c.
Timecounter i8254 frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) CPU 1.80GHz (1804.10-MHz 686-class CPU)
Origin = GenuineIntel Id = 0xf13 Stepping = 3
Features=0x3febfbffFPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM
real memory = 268369920 (255 MB)
avail memory = 251047936 (239 MB)
ACPI APIC Table: AMIINT INTEL845
ioapic0 Version 2.0 irqs 0-23 on motherboard
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: math processor on motherboard
npx0: INT 16 interface
acpi0: AMIINT INTEL845 on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 10 entries at 0xc00f7a60
acpi0: Power Button (fixed)
Timecounter ACPI-fast frequency 3579545 Hz quality 1000
ACPI-1287: *** Error: Method execution failed [\_SB_.PCI0.MDET] (Node
0xc16b2ba0), AE_AML_REGION_LIMIT
ACPI-1287: *** Error: Method execution failed [\_SB_.PCI0._CRS] (Node
0xc16b2ae0), AE_AML_REGION_LIMIT
ACPI-0175: *** Error: Method execution failed [\_SB_.PCI0._CRS] (Node
0xc16b2ae0), AE_AML_REGION_LIMIT
can't fetch resources for \_SB_.PCI0 - AE_AML_REGION_LIMIT
ACPI-1287: *** Error: Method execution failed [\_SB_.PCI0.MDET] (Node
0xc16b2ba0), AE_AML_REGION_LIMIT
ACPI-1287: *** Error: Method execution failed [\_SB_.MEM_._CRS] (Node
0xc16bd840), AE_AML_REGION_LIMIT
ACPI-0175: *** Error: Method execution failed [\_SB_.MEM_._CRS] (Node
0xc16bd840), AE_AML_REGION_LIMIT
can't fetch resources for \_SB_.MEM_ - AE_AML_REGION_LIMIT
acpi_timer0: 24-bit timer at 3.579545MHz port 0x808-0x80b on acpi0
acpi_cpu0: CPU on acpi0
acpi_cpu1: CPU on acpi0
device_probe_and_attach: acpi_cpu1 attach returned 6
acpi_button0: Power Button on acpi0
pcib0: ACPI Host-PCI bridge on acpi0
pci0: ACPI PCI bus on pcib0
agp0: Intel 82845 host to AGP bridge mem 0xe000-0xe3ff at device
0.0 on pci0
pcib1: PCI-PCI bridge at device 1.0 on pci0
pci1: PCI bus on pcib1
pcib1: slot 0 INTA is routed to irq 16
pci1: display, VGA at device 0.0 (no driver attached)
uhci0: Intel 82801DB (ICH4) USB controller USB-A port 0xd400-0xd41f irq 16
at device 29.0 on pci0
usb0: Intel 82801DB (ICH4) USB controller USB-A on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: Intel 82801DB (ICH4) USB controller USB-B port 0xd800-0xd81f irq 19
at device 29.1 on pci0
usb1: Intel 82801DB (ICH4) USB controller USB-B on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: Intel 82801DB (ICH4) USB controller USB-C port 0xdc00-0xdc1f irq 18
at device 29.2 on pci0
usb2: Intel 82801DB (ICH4) USB controller USB-C on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: serial bus, USB at device 29.7 (no driver attached)
pcib2: ACPI PCI-PCI bridge at device 30.0 on pci0
pci3: ACPI PCI bus on pcib2
pci3: network, ethernet at device 4.0 (no driver attached)
isab0: PCI-ISA bridge at device 31.0 on pci0
isa0: ISA bus on isab0
atapci0: Intel ICH4 UDMA100 controller port
0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170
Re: problem with MySon Ethernet Nics
yes, my Nic has own driver but ... only for Freebsd 2.x and 3.x. And this is its instruction Ok, so there are sources, but the driver structure from 4.x and 5.x differs a lot from 3.x, so they cannot work. pcib2: at device 30.0 on pci0 pci3: on pcib2 pci3: at device 4.0 (no driver attached) ok, these were the lines that were important. when i run command pciconf, i also met such error: Operation is not permitted Probably you weren't root, pciconf -lv needs root riviliges. With a 4.9-stable, it looks like this: pris 14:03 pciconf -lv pciconf: /dev/pci: Permission denied pris 14:03 su - Password: pris# pciconf -lv [EMAIL PROTECTED]:1:0: class=0x060400 card=0x chip=0x1a318086 rev=0x04 hdr=0x01 vendor = 'Intel Corporation' device = '82845/E/MP/MZ Brookdale CPU to AGP Bridge' class= bridge subclass = PCI-PCI In the case above, the entries of: pcib2 and pci3 are important, could you post them? Also please post a uname -a string of your system. Olaf Hoyer, thank you again i knows Nic's driver is for 2.x and 3.x, i have compiled its driver because i can not probe it i was root when using pciconf. I was confused and ... And I have just reinstall my freebsd 5.2, now i can run pciconf And this is the result: ---begin--- [EMAIL PROTECTED]:0:0: class=0x06 card=0x chip=0x1a308086 rev=0x11 hdr=0x00 vendor = 'Intel Corporation' device = '82845/E/MP/MZ Brookdale CPU to I/O Bridge' class= bridge subclass = HOST-PCI [EMAIL PROTECTED]:1:0: class=0x060400 card=0x chip=0x1a318086 rev=0x11 hdr=0x01 vendor = 'Intel Corporation' device = '82845/E/MP/MZ Brookdale CPU to AGP Bridge' class= bridge subclass = PCI-PCI [EMAIL PROTECTED]:29:0:class=0x0c0300 card=0x56611462 chip=0x24c28086 rev=0x02 hdr=0x00 vendor = 'Intel Corporation' device = '82801DB/DBM (ICH4/M) USB UHCI Controller #1' class= serial bus subclass = USB [EMAIL PROTECTED]:29:1:class=0x0c0300 card=0x56611462 chip=0x24c48086 rev=0x02 hdr=0x00 vendor = 'Intel Corporation' device = '82801DB/DBM (ICH4/M) USB UHCI Controller #2' class= serial bus subclass = USB [EMAIL PROTECTED]:29:2:class=0x0c0300 card=0x56611462 chip=0x24c78086 rev=0x02 hdr=0x00 vendor = 'Intel Corporation' device = '82801DB/DBM (ICH4/M) USB UHCI Controller #3' class= serial bus subclass = USB [EMAIL PROTECTED]:29:7:class=0x0c0320 card=0x39801462 chip=0x24cd8086 rev=0x02 hdr=0x00 vendor = 'Intel Corporation' device = '82801DB/DBM (ICH4/M) USB EHCI Controller' class= serial bus subclass = USB [EMAIL PROTECTED]:30:0:class=0x060400 card=0x chip=0x244e8086 rev=0x82 hdr=0x01 vendor = 'Intel Corporation' device = '82801BA/CA/DB/EB/ER (ICH2/3/4/5/5R) Hub Interface to PCI Bridge' class= bridge subclass = PCI-PCI [EMAIL PROTECTED]:31:0:class=0x060100 card=0x chip=0x24c08086 rev=0x02 hdr=0x00 vendor = 'Intel Corporation' device = '82801DB (ICH4) LPC Interface Bridge' class= bridge subclass = PCI-ISA [EMAIL PROTECTED]:31:1: class=0x01018a card=0x56611462 chip=0x24cb8086 rev=0x02 hdr=0x00 vendor = 'Intel Corporation' device = '82801DB (ICH4) UltraATA/100 EIDE Controller' class= mass storage subclass = ATA [EMAIL PROTECTED]:31:3:class=0x0c0500 card=0x56611462 chip=0x24c38086 rev=0x02 hdr=0x00 vendor = 'Intel Corporation' device = '82801DB/DBM (ICH4/M) SMBus Controller' class= serial bus subclass = SMBus [EMAIL PROTECTED]:31:5:class=0x040100 card=0x56611462 chip=0x24c58086 rev=0x02 hdr=0x00 vendor = 'Intel Corporation' device = '82801DB/DBM (ICH4/M) AC'97 Audio Controller' class= multimedia subclass = audio [EMAIL PROTECTED]:0:0: class=0x03 card=0x000510de chip=0x002810de rev=0x15 hdr=0x00 vendor = 'NVIDIA Corporation' device = 'NV5 TNT2 / TNT2 Pro' class= display subclass = VGA [EMAIL PROTECTED]:4:0: class=0x02 card=0x132010bd chip=0x08031516 rev=0x00 hdr=0x00 vendor = 'Myson Technology Inc' device = '803 series PCI Ethernet controller' class= network subclass = ethernet end--- afterthat i run # ifconfig -a -begin--- plip0: flags=8810POINTOPOINT,SIMPLEX,MULTICAST mtu 1500 lo0: flags=8049UP,LOOPBACK,RUNNING,MULTICAST mtu 16384 inet 127.0.0.1 netmask 0xff00 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 end-- I will post the uname -a string of system if needed but it looks like : FreeBSd 5.2 ... i386 ... GENERIC I have not rebuilt my kernel yet. any suggestions? Thanks in advanced www.airland.kiev.ua - Airland Network eMail ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
Re: problem with MySon Ethernet Nics
On Thursday 18 March 2004 18:09, Olaf Hoyer wrote: Ok, do you have any Information about the chipset used on these? What is needed, is the dmesg output, at least those lines where the nic is probed. should read something like: pci2: unknown card foo bar dmesg print out something like: pci2:Ethernet Carddriver not attached My Nics is: SURECOM EP-320X-S 100/10M Ethernet PCI Adapter i have tried to rebuilded the kernel and compiled its driver (basing on the instruction) into kernel several times but I have not succeeded It is said that freebsd 5.2 supported MySon Ethernet Nics and ... i am surprized . Maybe I have missed somthing? Please help me to solve this problem www.airland.kiev.ua - Airland Network eMail ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
problem with MySon Ethernet Nics
hello list I have just upgradated to freeBSD 5.2 but My freebsd box does not recognize Nic (Myson Ethernet Nic). Please help me to solve this problem Thank you, sorry for my poor english www.airland.kiev.ua - Airland Network eMail ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to [EMAIL PROTECTED]
