Re: Fujitsu Siemens Promergy RX100S4 [SOLVED]
Joerg Pulz ha scritto: If i remeber correctly, you have to enable the RAID option in the BIOS to configure the two disk as array, afterwards you must enter the BIOS again and switch to AHCI. As the ataraid driver detects the array by reading the metadata on the disks it should detect the array. I'm not 100 percent sure but i think this is the way i did it. pciconf -lv show the following for the atapci device (again there is AHCI mentioned in the output): - atap...@pci0:0:31:1:class=0x01018a card=0x10a51734 chip=0x27df8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) Ultra ATA Storage Controller' class = mass storage subclass = ATA atap...@pci0:0:31:2:class=0x010601 card=0x10a51734 chip=0x27c18086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801GB I/O Controller Hub SATA cc=AHCI' class = mass storage - Same output here, but changing the BIOS settings did not help. The only way I found to get it working was to build the mirror through atacontrol. bye Thanks av. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Fujitsu Siemens Promergy RX100S4
Anyone tried 7.1/amd64 on this? I have two SATA disks configured for mirroring in the BIOS; I see the two disks separately as ad devices, but no RAID device: I'd expect an ar0 or something. Is this card not supported? bye Thanks av. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Fujitsu Siemens Promergy RX100S4
I have two SATA disks configured for mirroring in the BIOS; I see the two disks separately as ad devices, but no RAID device: I'd expect an ar0 or something. I think that if it is hardware RAID, you should see only one disk. If it is not supported, you will not have access to the RAID error diagnostics in FreeBSD, but it should still appear as one single disk. Bests, olivier ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Fujitsu Siemens Promergy RX100S4
Hi, I think that if it is hardware RAID, you should see only one disk. My Promise controller does have my disks show up as ar0 -- but the disks are there as individuals (ad*) as well, and accessible (though I only use ar0*, for hopefully obvious reasons). At least, that's what I saw last time I looked (running 7-STABLE around ~7.1-RELEASE). I can check tonight if you want (and I get home on time ;-)). Regards, Peter. -- Aufgepasst: Sind Ihre Daten beim Online-Banking auch optimal geschützt? Jetzt informieren und absichern: https://homebanking.web.de/?mc=m...@footer. ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
Re: Fujitsu Siemens Promergy RX100S4
-BEGIN PGP SIGNED MESSAGE- Hash: SHA1 On Tue, 17 Mar 2009, Andrea Venturoli wrote: Anyone tried 7.1/amd64 on this? I have two SATA disks configured for mirroring in the BIOS; I see the two disks separately as ad devices, but no RAID device: I'd expect an ar0 or something. Is this card not supported? I've two of these here, both running 7.0 one as i386 and one as amd64. The amd64 box uses the onboard RAID. Here are the relevant dmesg parts: - atapci0: Intel ICH7 UDMA100 controller port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x37 6,0x3420-0x342f at device 31.1 on pci0 ata0: ATA channel 0 on atapci0 ata0: [ITHREAD] ata1: ATA channel 1 on atapci0 ata1: [ITHREAD] atapci1: Intel AHCI controller port 0x3440-0x3447,0x3434-0x3437,0x3438-0x343f, 0x3430-0x3433,0x3400-0x341f mem 0xfd000400-0xfd0007ff irq 19 at device 31.2 on p ci0 atapci1: [ITHREAD] atapci1: AHCI Version 01.10 controller with 4 ports detected ata2: ATA channel 0 on atapci1 ata2: [ITHREAD] ata3: ATA channel 1 on atapci1 ata3: [ITHREAD] ata4: ATA channel 2 on atapci1 ata4: port not implemented ata4: [ITHREAD] ata5: ATA channel 3 on atapci1 ata5: port not implemented ata5: [ITHREAD] acd0: CDRW HL-DT-STCD-RW/DVD DRIVE GCC-4244N/1.00 at ata0-master UDMA33 ad4: 238475MB WDC WD2500JS-55NCB1 10.02E01 at ata2-master SATA300 ad6: 238475MB WDC WD2500JS-55NCB1 10.02E01 at ata3-master SATA300 ar0: 238475MB Intel MatrixRAID RAID1 status: READY ar0: disk0 READY (master) using ad4 at ata2-master ar0: disk1 READY (mirror) using ad6 at ata3-master - If i remeber correctly, you have to enable the RAID option in the BIOS to configure the two disk as array, afterwards you must enter the BIOS again and switch to AHCI. As the ataraid driver detects the array by reading the metadata on the disks it should detect the array. I'm not 100 percent sure but i think this is the way i did it. pciconf -lv show the following for the atapci device (again there is AHCI mentioned in the output): - atap...@pci0:0:31:1:class=0x01018a card=0x10a51734 chip=0x27df8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) Ultra ATA Storage Controller' class = mass storage subclass = ATA atap...@pci0:0:31:2:class=0x010601 card=0x10a51734 chip=0x27c18086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801GB I/O Controller Hub SATA cc=AHCI' class = mass storage - The second box (running i386) is using geom_mirror and running fine. I would definitely vote for the geom_mirror way! kind regards Joerg - -- The beginning is the most important part of the work. -Plato -BEGIN PGP SIGNATURE- Version: GnuPG v2.0.9 (FreeBSD) iD8DBQFJv/kkSPOsGF+KA+MRAlM8AKDP/wc5839XQIzQN6dnFVScAnn+4wCfS5ZA p2H8lnmtJp+R6VkvwS2LOJY= =y1Nz -END PGP SIGNATURE- ___ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to freebsd-questions-unsubscr...@freebsd.org
