Re: Clandestine USB SD card slot
Whoops, I should send this to freebsd-stable instead of freebsd-usb. Sorry! -- George On 10/16/16 09:22, George Mitchell wrote: > On 10/15/16 23:10, Anthony Jenkins wrote: >> On 10/15/16 18:28, George Mitchell wrote: >>> FreeBSD 10.3-RELEASE-p7 #0: Thu Aug 11 18:38:15 UTC 2016 >>> Acer Aspire E15 >>> There is a slot on the front of this laptop which sure looks like an >>> SD card slot, which I hope corresponds to one of these: >>> >>> ugen1.1: at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) >>> pwr=SAVE (0mA) >>> ugen0.1: at usbus0, cfg=0 md=HOST spd=SUPER >>> (5.0Gbps) pwr=SAVE (0mA) >>> ugen2.1: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) >>> pwr=SAVE (0mA) >>> ugen1.2: at usbus1, cfg=0 md=HOST >>> spd=HIGH (480Mbps) pwr=SAVE (100mA) >>> ugen2.2: at usbus2, cfg=0 md=HOST >>> spd=HIGH (480Mbps) pwr=SAVE (100mA) >>> ugen0.2: at usbus0, cfg=0 md=HOST >>> spd=SUPER (5.0Gbps) pwr=ON (224mA) >>> ugen1.3: at usbus1, cfg=0 md=HOST spd=FULL >>> (12Mbps) pwr=SAVE (100mA) >>> ugen2.3: at usbus2, cfg=0 md=HOST >>> spd=FULL (12Mbps) pwr=ON (100mA) >>> ugen1.4: at usbus1, cfg=0 md=HOST >>> spd=LOW (1.5Mbps) pwr=ON (100mA) >>> ugen1.5: at usbus1, cfg=0 md=HOST spd=FULL >>> (12Mbps) pwr=SAVE (100mA) >>> ugen1.6: at usbus1, cfg=0 md=HOST >>> spd=FULL (12Mbps) pwr=ON (100mA) >>> ugen1.7: at usbus1, cfg=0 md=HOST >>> spd=FULL (12Mbps) pwr=ON (100mA) >>> ugen1.8: at usbus1, cfg=0 md=HOST >>> spd=HIGH (480Mbps) pwr=ON (500mA) >>> >>> But inserting a card into the slot produces no results, even with >>> sysctl hw.usb.umass.debug=1 hw.usb.ugen.debug=1 hw.usb.dev.debug=1. >>> (sysctl hw.usb.debug=1 produces way too much output all the time.) >>> Any suggestions on how I can get this slot to overcome its shyness? >>> (I am not subscribed to the list; please CC me.) -- George >> Your card reader is probably on the PCI bus (and likely not supported by >> FreeBSD); I couldn't find any of your USB Pid:Vids as card readers. >> >> [ajenkins@ajenkins-hplaptop ~]$ pciconf -lv >> ... >> none2@pci0:3:0:0: class=0xff card=0x1995103c chip=0x522910ec >> rev=0x01 hdr=0x00 >> vendor = 'Realtek Semiconductor Co., Ltd.' >> device = 'RTS5229 PCI Express Card Reader' >> >> Anthony Jenkins >> > Ah! It didn't occur to me to run pciconf. "pciconf -lv" shows this: > > sdhci_pci0@pci0:0:20:7: class=0x080501 card=0x08651025 chip=0x78131022 > rev=0x01 hdr=0x00 > vendor = 'Advanced Micro Devices, Inc. [AMD]' > device = 'FCH SD Flash Controller' > class = base peripheral > subclass = SD host controller > > So not only is it (apparently) recognized, but the sdhci_pci driver > attached to it! But inserting or removing a card shows no activity. > What's my next step? -- George > ___ freebsd-usb@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"
Re: Clandestine USB SD card slot
On 10/15/16 23:10, Anthony Jenkins wrote: > On 10/15/16 18:28, George Mitchell wrote: >> FreeBSD 10.3-RELEASE-p7 #0: Thu Aug 11 18:38:15 UTC 2016 >> Acer Aspire E15 >> There is a slot on the front of this laptop which sure looks like an >> SD card slot, which I hope corresponds to one of these: >> >> ugen1.1: at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) >> pwr=SAVE (0mA) >> ugen0.1: at usbus0, cfg=0 md=HOST spd=SUPER >> (5.0Gbps) pwr=SAVE (0mA) >> ugen2.1: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) >> pwr=SAVE (0mA) >> ugen1.2: at usbus1, cfg=0 md=HOST >> spd=HIGH (480Mbps) pwr=SAVE (100mA) >> ugen2.2: at usbus2, cfg=0 md=HOST >> spd=HIGH (480Mbps) pwr=SAVE (100mA) >> ugen0.2: at usbus0, cfg=0 md=HOST >> spd=SUPER (5.0Gbps) pwr=ON (224mA) >> ugen1.3: at usbus1, cfg=0 md=HOST spd=FULL >> (12Mbps) pwr=SAVE (100mA) >> ugen2.3: at usbus2, cfg=0 md=HOST >> spd=FULL (12Mbps) pwr=ON (100mA) >> ugen1.4: at usbus1, cfg=0 md=HOST >> spd=LOW (1.5Mbps) pwr=ON (100mA) >> ugen1.5: at usbus1, cfg=0 md=HOST spd=FULL >> (12Mbps) pwr=SAVE (100mA) >> ugen1.6: at usbus1, cfg=0 md=HOST >> spd=FULL (12Mbps) pwr=ON (100mA) >> ugen1.7: at usbus1, cfg=0 md=HOST >> spd=FULL (12Mbps) pwr=ON (100mA) >> ugen1.8: at usbus1, cfg=0 md=HOST >> spd=HIGH (480Mbps) pwr=ON (500mA) >> >> But inserting a card into the slot produces no results, even with >> sysctl hw.usb.umass.debug=1 hw.usb.ugen.debug=1 hw.usb.dev.debug=1. >> (sysctl hw.usb.debug=1 produces way too much output all the time.) >> Any suggestions on how I can get this slot to overcome its shyness? >> (I am not subscribed to the list; please CC me.) -- George > Your card reader is probably on the PCI bus (and likely not supported by > FreeBSD); I couldn't find any of your USB Pid:Vids as card readers. > > [ajenkins@ajenkins-hplaptop ~]$ pciconf -lv > ... > none2@pci0:3:0:0: class=0xff card=0x1995103c chip=0x522910ec > rev=0x01 hdr=0x00 > vendor = 'Realtek Semiconductor Co., Ltd.' > device = 'RTS5229 PCI Express Card Reader' > > Anthony Jenkins > Ah! It didn't occur to me to run pciconf. "pciconf -lv" shows this: sdhci_pci0@pci0:0:20:7: class=0x080501 card=0x08651025 chip=0x78131022 rev=0x01 hdr=0x00 vendor = 'Advanced Micro Devices, Inc. [AMD]' device = 'FCH SD Flash Controller' class = base peripheral subclass = SD host controller So not only is it (apparently) recognized, but the sdhci_pci driver attached to it! But inserting or removing a card shows no activity. What's my next step? -- George ___ freebsd-usb@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"
Clandestine USB SD card slot
FreeBSD 10.3-RELEASE-p7 #0: Thu Aug 11 18:38:15 UTC 2016 Acer Aspire E15 There is a slot on the front of this laptop which sure looks like an SD card slot, which I hope corresponds to one of these: ugen1.1: at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen0.1: at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA) ugen2.1: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.2: at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (100mA) ugen2.2: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (100mA) ugen0.2: at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=ON (224mA) ugen1.3: at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (100mA) ugen2.3: at usbus2, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA) ugen1.4: at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (100mA) ugen1.5: at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (100mA) ugen1.6: at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA) ugen1.7: at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA) ugen1.8: at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (500mA) But inserting a card into the slot produces no results, even with sysctl hw.usb.umass.debug=1 hw.usb.ugen.debug=1 hw.usb.dev.debug=1. (sysctl hw.usb.debug=1 produces way too much output all the time.) Any suggestions on how I can get this slot to overcome its shyness? (I am not subscribed to the list; please CC me.) -- George ___ freebsd-usb@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"
Re: 10-1-RELEASE xhci failure
On 10/09/16 15:33, George Mitchell wrote: > On 10/09/16 14:15, George Mitchell wrote: >> I have an Acer Aspire E15, with one allegedly USB 3.0 capable port and >> a Western Digital USB 3.0 drive; but they don't talk to each other. >> [...] > I left out how the xhci interface itself shows up in usbconfig: > > ugen0.1: at usbus0, cfg=0 md=HOST spd=SUPER > (5.0Gbps) pwr=SAVE (0mA) > > -- George > After upgrading to 10.3-RELEASE, the interface happily talks to the disk in USB 3.0 mode! Hurray! -- George ___ freebsd-usb@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"
10-1-RELEASE xhci failure
I have an Acer Aspire E15, with one allegedly USB 3.0 capable port and a Western Digital USB 3.0 drive; but they don't talk to each other. After plugging it in, usbconfig shows that there is a: ugen0.2: at usbus0, cfg=255 md=HOST spd=SUPER (5.0Gbps) pwr=ON (224mA) connected, but it does not attach to the umass driver. I turned on all the USB debugging sysctls I could find, and here's the portion of the system log: http://m5p.com/~george/10.1-RELEASE-p35-xhci-messages Have there been improvements in the xhci driver between 10.1 and 10.3 that might relate to the problem? The drive works on the USB 2.0 ports, but of course much more slowly than I assume it would in USB 3.0 mode. I am not subscribed to the freebsd-usb list, so please cc me on your reply. -- George ___ freebsd-usb@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"
Re: 9.0 umass problem
On 09/18/12 13:47, Hans Petter Selasky wrote: On Sunday 15 January 2012 20:36:09 Hans Petter Selasky wrote: On Sunday 15 January 2012 18:35:59 George Mitchell wrote: I have a USB compact flash reader-writer which is normally connected to my computer all the time but rarely contains a compact flash card. Here is a snippet from a verbose dmesg with FreeBSD 9.0-RC3: [...] Hi, Can you try 9-stable or apply this patch: http://svn.freebsd.org/changeset/base/240662 --HPS Probably not before Saturday, but thanks for the patch! -- George ___ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to freebsd-usb-unsubscr...@freebsd.org
9.0 umass problem
): SCSI status: Check Condition (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present) (da0:umass-sim0:0:0:0): Error 6, Unretryable error Opened disk da0 - 6 (which all took only a couple of seconds, compared to half a minute with 9.0.) When there is a flash card in the device, 9.0 behaves even worse, taking about two and a half minutes to do this: ugen0.5: vendor 0x05e3 at usbus0 umass0: vendor 0x05e3 USB TO IDE, class 0/0, rev 2.00/0.32, addr 5 on usbus0 umass0: SCSI over Bulk-Only; quirks = 0x4101 umass0:2:0:-1: Attached to scbus2 (probe0:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0? GEOM: new disk da0 pass2 at umass-sim0 bus 0 scbus2 target 0 lun 0 pass2: Generic STORAGE DEVICE 1.00 Removable Direct Access SCSI-0 device pass2: 1.000MB/s transfers da0 at umass-sim0 bus 0 scbus2 target 0 lun 0 da0: Generic STORAGE DEVICE 1.00 Removable Direct Access SCSI-0 device da0: 1.000MB/s transfers da0: 245MB (501760 512 byte sectors: 64H 32S/T 245C) ... (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Error 5, Retries exhausted (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Error 5, Retries exhausted (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Error 5, Retries exhausted (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Error 5, Retries exhausted Opened disk da0 - 5 (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Retrying command (da0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR (da0:umass-sim0:0:0:0): Error 5, Retries exhausted Opened disk da0 - 5 Suggestions? -- George Mitchell ___ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to freebsd-usb-unsubscr...@freebsd.org
