Re: [Freedos-user] Networking: With MS Client, Error 5: Access has been denied
But does your client machine know that? I.E. do you have the DNS server configured in the network settings? -Original Message- From: John Hupp [mailto:free...@prpcompany.com] Sent: Tuesday, June 16, 2015 10:42 AM To: Discussion and general questions about FreeDOS. Subject: Re: [Freedos-user] Networking: With MS Client, Error 5: Access has been denied The router provides DNS. On 6/16/2015 10:39 AM, Dave Kerber wrote: Do you have a DNS server configured? -Original Message- From: John Hupp [mailto:free...@prpcompany.com] Sent: Tuesday, June 16, 2015 9:48 AM To: Discussion and general questions about FreeDOS. Subject: Re: [Freedos-user] Networking: With MS Client, Error 5: Access has been denied Here's a reference, by the way, on the ipconfig usage that I mention below: ftp://ftp.microsoft.com/misc1/BUSSYS/LANMAN/KB/Q183/8/58.TXT A couple more observations: When I booted up this morning, ipconfig c:\net once again reported the lease expired, but the expiration time coincided exactly -- to the minute -- with the bootup time, and the lease-issued time was exactly 24 hours before I booted up this morning. Thinking to dodge the DHCP lease issue, I set up with a static IP outside the DHCP address scope (but still within the same subnet segment). Nonetheless ipconfig c:\net still reports an IP within the DHCP scope, rather than the static IP I assigned. Current functionality: I can successfully ping an IP address e.g. ping 8.8.8.8 but name resolution fails, so no-go on ping google.com. On 6/15/2015 8:25 PM, John Hupp wrote: I found out that ipconfig usage is not as expected for the DOS client. Ipconfig /all is meaningless. In my case, the one and only good command is ipconfig c:\net. This then reports (now again under DHCP), an IP address, gateway, and DNS server as expected. But it reports Lease Expired. Even after I forced the router to give it a brand new lease on a different IP, it still reports the lease expired. The router shows the lease as freshly issued with a day to live. The date and time are correct on client and server. Ideas? (And no, ipconfig /release or ipconfig /renew won't work either. They too are meaningless.) On 6/15/2015 12:19 PM, John Hupp wrote: I just tried changing the DOS client from DHCP to static configuration, and I still get the same net use error. Furthermore ipconfig /all still reports No DHCP data available. Shouldn't it report my static configuration info? On 6/15/2015 11:46 AM, John Hupp wrote: Fundamentals -- you may be onto something. Though TCP/IP initialization completes without error, running ipconfig /all yields No DHCP data available. I get the same result from two identical cards, both configured the same way. I do note that both cards are old non-PNP ISA cards, which I thought would be appropriate for this vintage rig. In the meantime, in the Registry I changed HKLM\SYSTEM\CurrentControlSet\Control\Lsa\LMCompatibilityLevel=3 - 0, which is Send LM NTLM responses per https://technet.microsoft.com/en- us/library/jj852207%28v=ws.10%29.aspx. Then I rebooted. But I still get the same error on the DOS client. @ Roberto Fazzalari: I have been avoiding your approach to date since I never had more than a rank novice's acquaintance with Wireshark. But it may be that I'll have to get reacquainted! On 6/15/2015 12:09 AM, Louis Santillan wrote: Be sure that you have a good IP, gateway, and DNS setting from your DHCP server. --- --- ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user -- ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user
Re: [Freedos-user] Networking: With MS Client, Error 5: Access has been denied
Do you have a DNS server configured? -Original Message- From: John Hupp [mailto:free...@prpcompany.com] Sent: Tuesday, June 16, 2015 9:48 AM To: Discussion and general questions about FreeDOS. Subject: Re: [Freedos-user] Networking: With MS Client, Error 5: Access has been denied Here's a reference, by the way, on the ipconfig usage that I mention below: ftp://ftp.microsoft.com/misc1/BUSSYS/LANMAN/KB/Q183/8/58.TXT A couple more observations: When I booted up this morning, ipconfig c:\net once again reported the lease expired, but the expiration time coincided exactly -- to the minute -- with the bootup time, and the lease-issued time was exactly 24 hours before I booted up this morning. Thinking to dodge the DHCP lease issue, I set up with a static IP outside the DHCP address scope (but still within the same subnet segment). Nonetheless ipconfig c:\net still reports an IP within the DHCP scope, rather than the static IP I assigned. Current functionality: I can successfully ping an IP address e.g. ping 8.8.8.8 but name resolution fails, so no-go on ping google.com. On 6/15/2015 8:25 PM, John Hupp wrote: I found out that ipconfig usage is not as expected for the DOS client. Ipconfig /all is meaningless. In my case, the one and only good command is ipconfig c:\net. This then reports (now again under DHCP), an IP address, gateway, and DNS server as expected. But it reports Lease Expired. Even after I forced the router to give it a brand new lease on a different IP, it still reports the lease expired. The router shows the lease as freshly issued with a day to live. The date and time are correct on client and server. Ideas? (And no, ipconfig /release or ipconfig /renew won't work either. They too are meaningless.) On 6/15/2015 12:19 PM, John Hupp wrote: I just tried changing the DOS client from DHCP to static configuration, and I still get the same net use error. Furthermore ipconfig /all still reports No DHCP data available. Shouldn't it report my static configuration info? On 6/15/2015 11:46 AM, John Hupp wrote: Fundamentals -- you may be onto something. Though TCP/IP initialization completes without error, running ipconfig /all yields No DHCP data available. I get the same result from two identical cards, both configured the same way. I do note that both cards are old non-PNP ISA cards, which I thought would be appropriate for this vintage rig. In the meantime, in the Registry I changed HKLM\SYSTEM\CurrentControlSet\Control\Lsa\LMCompatibilityLevel=3 - 0, which is Send LM NTLM responses per https://technet.microsoft.com/en- us/library/jj852207%28v=ws.10%29.aspx. Then I rebooted. But I still get the same error on the DOS client. @ Roberto Fazzalari: I have been avoiding your approach to date since I never had more than a rank novice's acquaintance with Wireshark. But it may be that I'll have to get reacquainted! On 6/15/2015 12:09 AM, Louis Santillan wrote: Be sure that you have a good IP, gateway, and DNS setting from your DHCP server. --- --- ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user -- ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user
Re: [Freedos-user] Networking: With MS Client, Error 5: Access has been denied
Are you trying to connect by dns name, or by IP address? To take one level of possible trouble out of the equation, try connecting by IP addr. -Original Message- From: John Hupp [mailto:free...@prpcompany.com] Sent: Monday, June 15, 2015 12:20 PM To: Discussion and general questions about FreeDOS. Subject: Re: [Freedos-user] Networking: With MS Client, Error 5: Access has been denied I just tried changing the DOS client from DHCP to static configuration, and I still get the same net use error. Furthermore ipconfig /all still reports No DHCP data available. Shouldn't it report my static configuration info? On 6/15/2015 11:46 AM, John Hupp wrote: Fundamentals -- you may be onto something. Though TCP/IP initialization completes without error, running ipconfig /all yields No DHCP data available. I get the same result from two identical cards, both configured the same way. I do note that both cards are old non-PNP ISA cards, which I thought would be appropriate for this vintage rig. In the meantime, in the Registry I changed HKLM\SYSTEM\CurrentControlSet\Control\Lsa\LMCompatibilityLevel=3 - 0, which is Send LM NTLM responses per https://technet.microsoft.com/en- us/library/jj852207%28v=ws.10%29.aspx. Then I rebooted. But I still get the same error on the DOS client. @ Roberto Fazzalari: I have been avoiding your approach to date since I never had more than a rank novice's acquaintance with Wireshark. But it may be that I'll have to get reacquainted! On 6/15/2015 12:09 AM, Louis Santillan wrote: Be sure that you have a good IP, gateway, and DNS setting from your DHCP server. --- --- ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user -- ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user
Re: [Freedos-user] HTML5/Javascript/Flash (was: Re: Quickview ver 2.60)
Yes, you need an RJ-11 jack (not RJ-45) on the wall, which is terminated with copper, but I have FiOS at my house, which is fiber to the wall of my garage, and a media converter to the copper that runs throughout my house. That is still how most houses are wired even if they have DSL or Fiber to the house: copper inside, tranlsated to fiber or cable before it leaves the premises. Dialup modems work fine in all those cases. -Original Message- From: dmccunney [mailto:dennis.mccun...@gmail.com] Sent: Sunday, December 21, 2014 4:52 PM To: Discussion and general questions about FreeDOS. Subject: Re: [Freedos-user] HTML5/Javascript/Flash (was: Re: Quickview ver 2.60) On Sun, Dec 21, 2014 at 12:54 PM, Dale E Sterner sunbeam...@juno.com wrote: Copper is long gone and my dial up still works.Fiber is just a carrier. Dial up uses analog signals transmitted over copper wire. Fiber is digital end-to-end. When you dial up, you presumably use a modem and connect via an RJ45 jack to a connector on the wall. What does the connecter have inside? I'm willing to bet a lot it's copper wire. The wire will teminate in a mux somewhere in the basement of your building or in the street, and long haul traffic will be over fiber, but the conversion from analog to digital happens elsewhere. (And what the telco historically used was *not* TCP-IP. They sent digital packets, but used a completely different protocol. I used to *be* a telecom admin. I actually know something about this.) In my area, copper at the point where the user will connect is no longer available. It's fiber end-to-end. Existing copper installations still work, but if they fail they will not be repaired. Verizon is treating hurricane Sandy damage as a good excuse to drop copper, and people who had copper that failed because of hurricane damage have already been told it won't be fixed, and their options are cell phone and/or fiber. Peon is anyone who takes orders from a boss. Just about everybody. And the boss is the one who should be in control? Dial up is so slow it would take years to clean out Sony instead of minutes or hours. Dial up is so slow Sony would not be able to do business in their current fashion if they were restricted to it. Neither would anybody else. You would not like living in the world that would result. Sony was most likely an inside job. Some peon probably did it - revenge or money who knows. Speculation is all over the web, with current fingers mostly pointing at politically motivated hackers in NK, who were unhappy about a new Sony Pictures film that portrayed their leader in an unflattering light. Sony uses broadband and was the exit point for their billion dollar files. They didn't leave Sony in a brief case. Hacks like the one that breached Sony occurred back when stuff *was* still dial up. Slower speed may make it take longer to get the data, but will not prevent the breach. DS. __ Dennis https://plus.google.com/u/0/105128793974319004519 --- --- Download BIRT iHub F-Type - The Free Enterprise-Grade BIRT Server from Actuate! Instantly Supercharge Your Business Reports and Dashboards with Interactivity, Sharing, Native Excel Exports, App Integration more Get technology previously reserved for billion-dollar corporations, FREE http://pubads.g.doubleclick.net/gampad/clk?id=164703151iu=/4140/ostg.c lktrk ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user -- Dive into the World of Parallel Programming! The Go Parallel Website, sponsored by Intel and developed in partnership with Slashdot Media, is your hub for all things parallel software development, from weekly thought leadership blogs to news, videos, case studies, tutorials and more. Take a look and join the conversation now. http://goparallel.sourceforge.net ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user
Re: [Freedos-user] HTML5/Javascript/Flash (was: Re: Quickview ver 2.60)
-Original Message- From: dmccunney [mailto:dennis.mccun...@gmail.com] Sent: Sunday, December 21, 2014 12:35 PM To: Discussion and general questions about FreeDOS. Subject: Re: [Freedos-user] HTML5/Javascript/Flash (was: Re: Quickview ver 2.60) ... Dial up still works the same without copper - real slow No it doesn't. Dial up *requires* copper. It does not exist on fiber links. *Broadband* can exist on copper, with ISDN and DSL service the prominent examples, but broadband is increasingly fiber these days too. No, dialup does not require copper. I know from personal experience that it works fine on a FiOS or DSL line. If you have a dialtone when you pick up your landline phone, a dialup modem will work. DS __ Dennis https://plus.google.com/u/0/105128793974319004519 --- --- Download BIRT iHub F-Type - The Free Enterprise-Grade BIRT Server from Actuate! Instantly Supercharge Your Business Reports and Dashboards with Interactivity, Sharing, Native Excel Exports, App Integration more Get technology previously reserved for billion-dollar corporations, FREE http://pubads.g.doubleclick.net/gampad/clk?id=164703151iu=/4140/ostg.c lktrk ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user -- Dive into the World of Parallel Programming! The Go Parallel Website, sponsored by Intel and developed in partnership with Slashdot Media, is your hub for all things parallel software development, from weekly thought leadership blogs to news, videos, case studies, tutorials and more. Take a look and join the conversation now. http://goparallel.sourceforge.net ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user
Re: [Freedos-user] Quickview ver 2.60
-Original Message- From: dmccunney [mailto:dennis.mccun...@gmail.com] Sent: Tuesday, December 02, 2014 8:55 PM To: Discussion and general questions about FreeDOS. Subject: Re: [Freedos-user] Quickview ver 2.60 ... When I try to format very large SD chips with DOS; the software just gives up. Small sd chips do format but slowly. Large CF chips format in a few seconds. That's an OS and old hardware issue, It's not inherent to SD. To a certain extent it is. SD has a slower interface than CF does. That's why all high-end cameras use CF rather than SD cards. -- Download BIRT iHub F-Type - The Free Enterprise-Grade BIRT Server from Actuate! Instantly Supercharge Your Business Reports and Dashboards with Interactivity, Sharing, Native Excel Exports, App Integration more Get technology previously reserved for billion-dollar corporations, FREE http://pubads.g.doubleclick.net/gampad/clk?id=164703151iu=/4140/ostg.clktrk ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user
Re: [Freedos-user] Quickview ver 2.60
-Original Message- From: Ralf Quint [mailto:freedos...@gmail.com] Sent: Wednesday, December 03, 2014 3:41 PM To: freedos-user@lists.sourceforge.net Subject: Re: [Freedos-user] Quickview ver 2.60 On 12/3/2014 5:23 AM, Dave Kerber wrote: That's an OS and old hardware issue, It's not inherent to SD. To a certain extent it is. SD has a slower interface than CF does. That's why all high-end cameras use CF rather than SD cards. Really? All my clients that use high-end cameras (this is Hollywood just over the hills from me) are using SDHC or SDXC these days. I'm talking about still cameras (DSLR), not video. I know nothing about video cameras, except that their recording speed requirements are noticeably lower than high-end still cameras. CF has only a real advantage that it is royalty free and are in a lot of cases, easier to handle than SD cards where there is an unfortunate trend to the miniSD and microSD formats, which are a pain in the posterior for anyone but a 4 year old toddler to handle because of their size (or rather, the lack thereof). CFs are making a bit of a comeback though in embedded environments, as they come in some more rugged casings and that the latest interface specs is based on PCIexpress, which has become a staple in embedded computing... They have been in Canon's and Nikon's high-end camera bodies for a long time, and continue to be. Ralf --- This email has been checked for viruses by Avast antivirus software. http://www.avast.com -- Download BIRT iHub F-Type - The Free Enterprise-Grade BIRT Server from Actuate! Instantly Supercharge Your Business Reports and Dashboards with Interactivity, Sharing, Native Excel Exports, App Integration more Get technology previously reserved for billion-dollar corporations, FREE http://pubads.g.doubleclick.net/gampad/clk?id=164703151iu=/41 40/ostg.clktrk ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user -- Download BIRT iHub F-Type - The Free Enterprise-Grade BIRT Server from Actuate! Instantly Supercharge Your Business Reports and Dashboards with Interactivity, Sharing, Native Excel Exports, App Integration more Get technology previously reserved for billion-dollar corporations, FREE http://pubads.g.doubleclick.net/gampad/clk?id=164703151iu=/4140/ostg.clktrk ___ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user
