Re: [U-Boot] SMSC LAN9514 on TI DM37x board
Dear Felix Radensky, !DOCTYPE HTML PUBLIC -//W3C//DTD HTML 4.01 Transitional//EN html head meta content=text/html; charset=ISO-8859-1 http-equiv=Content-Type /head [...] I cannot read this email, ignored, sorry. Best regards, Marek Vasut ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] SMSC LAN9514 on TI DM37x board
Hi Ilya, On 11/06/2012 01:01 PM, Ilya Yanok wrote: On Tue, Nov 6, 2012 at 9:24 AM, Felix Radensky fe...@embedded-sol.com mailto:fe...@embedded-sol.com wrote: Hi Marek, On 11/06/2012 12:57 AM, Marek Vasut wrote: Can you please avoid top-posting? Does U-Boot even support your USB device? Sorry about top-posting. My USB device is supported by smsc95xx.c driver in drivers/usb/eth. Judging by the portion of config you cited you don't have it enabled. But I don't think that's your current problem (you should see your device after usb start even if there is no driver for it). I'd verify PHY configuration if I were you. Regards, Ilya. Thanks for replying. I do have the following definitions as well: #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_SMSC95XX I'm going to compare u-boot and kernel PHY initializations. They are not the same, and in linux everything works. Felix. ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] SMSC LAN9514 on TI DM37x board
Hi Marek, On 11/06/2012 12:57 AM, Marek Vasut wrote: Can you please avoid top-posting? Does U-Boot even support your USB device? Sorry about top-posting. My USB device is supported by smsc95xx.c driver in drivers/usb/eth. Thanks a lot. Felix. On 11/02/2012 08:38 AM, Felix Radensky wrote: Hi, I'm running u-boot-2012.10 on a custom DM37x based board. The board has LAN9514 USB Ethernet adapter connected in EHCI host controller via USB3320 ULPI PHY. This is very similar to BeagleBoard XM. Both Ethernet and USB hub work in linux-2.6.37 from TI PSP 04.02.00.07. In u-boot however, neither Ethernet nor mass storage devices attached to hub are not detected. Below is boot log: U-Boot 2012.10 (Nov 02 2012 - 00:44:41) OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz Pro4Tech MVC404 board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 In:serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 MVC404 usb start (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found scanning bus for ethernet devices... 0 Ethernet Device(s) found MVC404 usb info 1: Hub, USB Revision 2.0 - u-boot EHCI Host Controller - Class: Hub - PacketSize: 64 Configurations: 1 - Vendor: 0x Product 0x Version 1.0 Configuration: 1 - Interfaces: 1 Self Powered 0mA Interface: 0 - Alternate Setting 0, Endpoints: 1 - Class Hub - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms I have the following definitions in the code: #define CONFIG_USB_OMAP3 #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS3 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO24 #define CONFIG_USB_ULPI #define CONFIG_USB_ULPI_VIEWPORT_OMAP #define CONFIG_USB_STORAGE static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED }; MUX_VAL(CP(ETK_D15_ES2),(IDIS | PTD | DIS | M4)) /*GPIO_24*/ I'd appreciate any help in fixing the problem. Thanks. Felix Radensky. ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot Felix. ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] SMSC LAN9514 on TI DM37x board
On Tue, Nov 6, 2012 at 9:24 AM, Felix Radensky fe...@embedded-sol.comwrote: Hi Marek, On 11/06/2012 12:57 AM, Marek Vasut wrote: Can you please avoid top-posting? Does U-Boot even support your USB device? Sorry about top-posting. My USB device is supported by smsc95xx.c driver in drivers/usb/eth. Judging by the portion of config you cited you don't have it enabled. But I don't think that's your current problem (you should see your device after usb start even if there is no driver for it). I'd verify PHY configuration if I were you. Regards, Ilya. ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] SMSC LAN9514 on TI DM37x board
Hi Marek, Can you please take a look at this problem. Thanks a lot. Felix. On 11/02/2012 08:38 AM, Felix Radensky wrote: Hi, I'm running u-boot-2012.10 on a custom DM37x based board. The board has LAN9514 USB Ethernet adapter connected in EHCI host controller via USB3320 ULPI PHY. This is very similar to BeagleBoard XM. Both Ethernet and USB hub work in linux-2.6.37 from TI PSP 04.02.00.07. In u-boot however, neither Ethernet nor mass storage devices attached to hub are not detected. Below is boot log: U-Boot 2012.10 (Nov 02 2012 - 00:44:41) OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz Pro4Tech MVC404 board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 In:serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 MVC404 usb start (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found scanning bus for ethernet devices... 0 Ethernet Device(s) found MVC404 usb info 1: Hub, USB Revision 2.0 - u-boot EHCI Host Controller - Class: Hub - PacketSize: 64 Configurations: 1 - Vendor: 0x Product 0x Version 1.0 Configuration: 1 - Interfaces: 1 Self Powered 0mA Interface: 0 - Alternate Setting 0, Endpoints: 1 - Class Hub - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms I have the following definitions in the code: #define CONFIG_USB_OMAP3 #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS3 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO24 #define CONFIG_USB_ULPI #define CONFIG_USB_ULPI_VIEWPORT_OMAP #define CONFIG_USB_STORAGE static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED }; MUX_VAL(CP(ETK_D15_ES2),(IDIS | PTD | DIS | M4)) /*GPIO_24*/ I'd appreciate any help in fixing the problem. Thanks. Felix Radensky. ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Re: [U-Boot] SMSC LAN9514 on TI DM37x board
Dear Felix Radensky, Hi Marek, Can you please take a look at this problem. Can you please avoid top-posting? Does U-Boot even support your USB device? Thanks a lot. Felix. On 11/02/2012 08:38 AM, Felix Radensky wrote: Hi, I'm running u-boot-2012.10 on a custom DM37x based board. The board has LAN9514 USB Ethernet adapter connected in EHCI host controller via USB3320 ULPI PHY. This is very similar to BeagleBoard XM. Both Ethernet and USB hub work in linux-2.6.37 from TI PSP 04.02.00.07. In u-boot however, neither Ethernet nor mass storage devices attached to hub are not detected. Below is boot log: U-Boot 2012.10 (Nov 02 2012 - 00:44:41) OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz Pro4Tech MVC404 board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 In:serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 MVC404 usb start (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found scanning bus for ethernet devices... 0 Ethernet Device(s) found MVC404 usb info 1: Hub, USB Revision 2.0 - u-boot EHCI Host Controller - Class: Hub - PacketSize: 64 Configurations: 1 - Vendor: 0x Product 0x Version 1.0 Configuration: 1 - Interfaces: 1 Self Powered 0mA Interface: 0 - Alternate Setting 0, Endpoints: 1 - Class Hub - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms I have the following definitions in the code: #define CONFIG_USB_OMAP3 #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS3 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO24 #define CONFIG_USB_ULPI #define CONFIG_USB_ULPI_VIEWPORT_OMAP #define CONFIG_USB_STORAGE static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED }; MUX_VAL(CP(ETK_D15_ES2),(IDIS | PTD | DIS | M4)) /*GPIO_24*/ I'd appreciate any help in fixing the problem. Thanks. Felix Radensky. ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
[U-Boot] SMSC LAN9514 on TI DM37x board
Hi, I'm running u-boot-2012.10 on a custom DM37x based board. The board has LAN9514 USB Ethernet adapter connected in EHCI host controller via USB3320 ULPI PHY. This is very similar to BeagleBoard XM. Both Ethernet and USB hub work in linux-2.6.37 from TI PSP 04.02.00.07. In u-boot however, neither Ethernet nor mass storage devices attached to hub are not detected. Below is boot log: U-Boot 2012.10 (Nov 02 2012 - 00:44:41) OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz Pro4Tech MVC404 board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 In:serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 MVC404 usb start (Re)start USB... USB: Register 1313 NbrPorts 3 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found scanning bus for ethernet devices... 0 Ethernet Device(s) found MVC404 usb info 1: Hub, USB Revision 2.0 - u-boot EHCI Host Controller - Class: Hub - PacketSize: 64 Configurations: 1 - Vendor: 0x Product 0x Version 1.0 Configuration: 1 - Interfaces: 1 Self Powered 0mA Interface: 0 - Alternate Setting 0, Endpoints: 1 - Class Hub - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms I have the following definitions in the code: #define CONFIG_USB_OMAP3 #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS3 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO24 #define CONFIG_USB_ULPI #define CONFIG_USB_ULPI_VIEWPORT_OMAP #define CONFIG_USB_STORAGE static struct omap_usbhs_board_data usbhs_bdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED }; MUX_VAL(CP(ETK_D15_ES2),(IDIS | PTD | DIS | M4)) /*GPIO_24*/ I'd appreciate any help in fixing the problem. Thanks. Felix Radensky. ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot