See cable beam stifferDo on 3 or 4 sides.Be safeDale
코스피
|
|
|
| | |
|
|
|
| |
코스피
코스피
|
|
|
On Monday, May 13, 2024 at 08:07:14 PM EDT, Dale Ertley
wrote:
Small blocks on the outside middle of beam on 3 or 4 sides of the beam with
small aircraft cable attached
Small blocks on the outside middle of beam on 3 or 4 sides of the beam with
small aircraft cable attached to each end pulled tight.
Use small turn buckles to tighten the cables over the block on that one
side.You may be able to reduce the mass of the beam with the added stiffness of
the blocks
it.
https://www.gibbscam.com/en
John
> -Original Message-
> From: Dale Ertley via Emc-users [mailto:emc-users@lists.sourceforge.net]
> Sent: March 21, 2024 7:52 AM
> To: Enhanced Machine Controller (EMC)
> Cc: Dale Ertley
> Subject: Re: [Emc-users] HAAS file
>
>
> H
Have you looked at the files with a text editor. Notepad should works.
It may be a G code file but just made on the machine and not in a cad software.
I have gone to Cimco Edit to see where a file is messed
up.https://www.cimco.com/software/cimco-edit/That is after the post output.
Sorry I
for the info. Those might well serve me in case of using the
original DC servos the machine has.
El vie, 9 feb 2024 a las 21:37, Dale Ertley via Emc-users (<
emc-users@lists.sourceforge.net>) escribió:
> I have 4 drives am going to try from Machdrives.com. They use Tuna
> graphical soft
I have 4 drives am going to try from Machdrives.com. They use Tuna graphical
software to tune the drives.It is going to be a few months till I get them
installed. I will post results then.
Be safe.
BRF Servo DriveAUD$159
A high performance, 160V 20A brushed DC servo drive. Ideal for CNC
What is the chance that a BIPAP (twopressure system) machine could be used as
a “first line” for a ventilator?
A CPAP (single pressure system) may also work.
It might even work with an O2concentrator.
Pressures could be raised andlowered if necessary.
I don’t think it could be used with
Hello all,I was going to try the new LinuxCNC 2.7.15 releace but I can not find
the download.The page is there with a list of the new contributors and the many
things that have been fixed.Just can't seem to find where to download.Also is
2.7.15 setup to be put on a USB drive to install?Thank
Gene,
Watch out for embedded trash in the download before you move it to a good
computer.
Or just print out the info from the USB booted computer.
Dale
On Saturday, January 26, 2019, 7:59:42 PM EST, Dale Ertley via Emc-users
wrote:
Gene,
Will this work for you?
Do you have an old
Gene,
Will this work for you?
Do you have an old used computer with only linux operating system on it?
NO INFORMATION. wipe drive
Or boot from a new USB jump drive with only linux CNC operating system.
Link to that with a NEW EMAIL address from google/yahoo. Then delete it.
Dale
On
, Dale Ertley via Emc-users wrote:
> This might be a nice way to go off grid. I have 2 HDT Balance of System
>(BOS) units with 5 solar panels. Engineer told me I could tie 2 together to
>get 220 v ac out. Outback GTFX2524, FLEXmax 60, and alot more in them. I will
>let them go for m
This might be a nice way to go off grid. I have 2 HDT Balance of System (BOS)
units with 5 solar panels. Engineer told me I could tie 2 together to get 220 v
ac out. Outback GTFX2524, FLEXmax 60, and alot more in them. I will let them go
for my cost. Got at gov auction. No batteries.
Balance
12 matches
Mail list logo