When I try and start asterisk I get the following, however I have commented out
the data the connections in res_mysql.conf and res_pgsql.conf. I am not sure
therefore why I am getting these errors. Do I have to change something else to
turn this off?
Thanks
Asterisk 1.4.21.2~dfsg-3, Copyright
...@lists.digium.com
[mailto:asterisk-users-boun...@lists.digium.com] On Behalf Of Tzafrir Cohen
Sent: 03 May 2009 14:11
To: asterisk-users@lists.digium.com
Subject: Re: [asterisk-users] Asterisk not starting up due to database problems
On Sun, May 03, 2009 at 01:30:49PM +0100, Charlie Grosvenor wrote
I have tried to compile asterisk with zaptel:
./configure --with-zaptel=/usr/src/zaptel-1.4.0
make
make install
however when I run asterisk it says that the zap command is missing.
What am I doing wrong? I have compiled and installed zaptel fine and it
is recognizing my card.
Thanks
: [asterisk-users] X100P - zttools says red status
Charlie Grosvenor wrote:
Yes the line is connected, a standard phone works fine when connected
to
the line.
There're 2 ports on the card. Which port are you using? One of the ports
is for connecting another phone in parallel to the card.
Leo
I have an X100P which I have set up as per the guidelines:
http://www.x100p.com/support/doc/quick_start_fxo.php
The card is recognized by the system:
Zaptel Version: 1.4.0
Echo Canceller: MG2
Configuration
==
Channel map:
Channel 01: FXS Kewlstart
- zttools says red status
On Fri, Jan 26, 2007 at 08:42:36PM -, Charlie Grosvenor wrote:
I have an X100P which I have set up as per the guidelines:
http://www.x100p.com/support/doc/quick_start_fxo.php
The card is recognized by the system:
Zaptel Version: 1.4.0
Echo Canceller: MG2
, Jan 22, 2007 at 08:08:16PM -, Charlie Grosvenor wrote:
I have just purchased a 2nd hand X100P,
Is there another X100P card in the same system?
if I do a ztcfg -vv I get:
Zaptel Version: 1.4.0
Echo Canceller: MG2
Configuration
==
Channel map:
Channel 01: FXS
I have just purchased a 2nd hand X100P, if I do a ztcfg -vv I get:
Zaptel Version: 1.4.0
Echo Canceller: MG2
Configuration
==
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
1 channels configured.
My understanding of the above is that the zaptel driver has
that alarms: red. The card is connected to the
phone line. Anybody any idea what the problem is?
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Charlie
Grosvenor
Sent: 22 January 2007 20:08
To: asterisk-users@lists.digium.com
Subject: [asterisk-users] X100P how
I am using Voip Talk and have my extensions.conf set up to make outgoing
calls:
exten = _0[1-9].,1,Dial(IAX2/[EMAIL PROTECTED]/44${EXTEN:1})
exten = _00.,1,Dial(IAX2/[EMAIL PROTECTED]/${EXTEN:2})
exten = _09XX,1,Dial(IAX2/[EMAIL PROTECTED]/${EXTEN})
What I want to do is have extension
- Non-Commercial Discussion
Subject: Re: [asterisk-users] Escalate Call To Mobile
Also the timeout to Dial is in SECONDS, not RINGS. In the USA a ring
cycle is about 6 seconds.
C F wrote:
You Dont Have A Priority 1 And You Have Priority 2 Twice
On 12/24/06, Charlie Grosvenor [EMAIL PROTECTED
I have managed to resolve this. If anybody is interested my machine is
multihomed. I set IAX.conf and SIP.conf just to listen on one ip
address, this seemed to solve the problem.
Regards
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Charlie
Grosvenor
Sent: 14 December 2006
[default]
Some extensions defined
exten = _0[1-9].,1,Dial(IAX2/[EMAIL PROTECTED]/44${EXTEN:1})
exten = _00.,1,Dial(IAX2/[EMAIL PROTECTED]/${EXTEN:2})
exten = _09XX,1,Dial(IAX2/[EMAIL PROTECTED]/${EXTEN})
I have the above defined in extensions.conf. This enables me to make
outgoing
I am trying to get asterisks to work with http://www.voiptalk.org 's IAX
service. I have configured asterisks as per their instructions and am
using the x-lite soft phone. When I get an incoming call the softphone
rings but the caller (from pstn) gets a recorded message saying the
number is unable
Thanks for you reply, it does not output anything on the console when i
make the call. However i have turned on SIP Debug and get the following:
-- SIP read from 192.168.2.3:8099:
REGISTER sip:192.168.1.1:5060 SIP/2.0
Via: SIP/2.0/UDP 192.168.2.3:8099;rport;branch=z9hG4bK32333
From: sip:[EMAIL
: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Doug Lytle
Sent: 16 November 2006 00:47
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] PortSip and Astericks new install
Charlie Grosvenor wrote:
Thanks for your reply, I have tried what you have
: Re: [asterisk-users] PortSip and Astericks new install
Charlie Grosvenor wrote:
I have tried the configuration exactly the same of yours and it's still
not working. What could be wrong with my installation? I first of all
Show us what being displayed on the Asterisk console, also show
I have just installed Asterisk and installed the sample configuration
files. Asterisks appears to be working and I have added a SIP client:
[John]
type=friend
secret=test
host=dynamic
allow=all
I have been trying to dial the demo number 500 when using PortSip,
Asterisks answers the
Of Doug Lytle
Sent: 15 November 2006 21:07
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] PortSip and Astericks new install
Charlie Grosvenor wrote:
[John]
type=friend
secret=test
host=dynamic
allow=all
Try:
disallow=all
allow=alaw
allow=ulaw
19 matches
Mail list logo