Hi All,
I am trying to tune out some echo on a analogue line and have run
ztmonitor to get some info. When i run it, i get a RX reading when the
line is idle - is this normal? eg:
[EMAIL PROTECTED] zaptel-1.2.10]# ./ztmonitor 1 -vv
Visual Audio Levels.
Use zapata.conf
On Wed, Jan 10, 2007 at 05:41:50PM +1100, Ben Dinnerville wrote:
Hi All,
I am trying to tune out some echo on a analogue line and have run
ztmonitor to get some info. When i run it, i get a RX reading when the
line is idle - is this normal? eg:
[EMAIL PROTECTED] zaptel-1.2.10]#
On Fri, Dec 15, 2006 at 06:41:58PM -0800, Yuan LIU wrote:
Hardware is an SM56 card (X100P clone). When the line hangs up, ztmonitor
displays full bar (or whatever maximum allowed by rxgain) in RX. It only
drops zero when the line picks up (and remote was silent). Is this
something of
Hardware is an SM56 card (X100P clone). When the line hangs up, ztmonitor
displays full bar (or whatever maximum allowed by rxgain) in RX. It only
drops zero when the line picks up (and remote was silent). Is this
something of concern? The zap channel seems to work despite echo.
I have been having no success with my zap interface, and am trying to
use ztmonitor to fix it.
I am running Trixbox 1.1 and so far have one x100p card (shows up as
'Wildcard).
I tried many manual attempts at setting rx and tx gain with no results.
Then I read:
On Fri, Jul 07, 2006 at 10:57:02AM -0400, Robert Moskowitz wrote:
I have been having no success with my zap interface, and am trying to
use ztmonitor to fix it.
I am running Trixbox 1.1 and so far have one x100p card (shows up as
'Wildcard).
I tried many manual attempts at setting rx
Tzafrir Cohen wrote:
On Fri, Jul 07, 2006 at 10:57:02AM -0400, Robert Moskowitz wrote:
I have been having no success with my zap interface, and am trying to
use ztmonitor to fix it.
I am running Trixbox 1.1 and so far have one x100p card (shows up as
'Wildcard).
I tried many manual
On Fri, Jul 07, 2006 at 12:58:19PM -0400, Robert Moskowitz wrote:
Tzafrir Cohen wrote:
On Fri, Jul 07, 2006 at 10:57:02AM -0400, Robert Moskowitz wrote:
But ztmonitor 1 -vv does not produce any numeric information. Adding -f
file results in a file of zero length, perhaps since the only way
Have you tried putting a Hangup in your extensions.conf?On 4/13/06, Min Hwan Chang [EMAIL PROTECTED]
wrote:Details:Asterisk 1.0.9 Zaptel 1.0
Dell P3 1ghz with X100P Clone Location: IndiaThis is an interesting issue where when I open up ZTMonitor, it shows the RX as being on. It seems that Zaptel
Err, stupid me. Seems like the phone is hungup, but when I start ztmonitor, the line is picked up. I guess the line in India is pretty loud b/c the RX bounces off the charts, changed it to (-4) and all my problems are solved.
Regards,Min ChangOn 4/14/06, Kyle Sexton [EMAIL PROTECTED] wrote:
Have
Details:Asterisk 1.0.9 Zaptel 1.0 Dell P3 1ghz with X100P Clone Location: IndiaThis is an interesting issue where when I open up ZTMonitor, it shows the RX as being on. It seems that Zaptel doesn't know to hang up the line so after a couple of hours when the telecom cuts the line, everythign stops
Good Day,
I have a weird issue using zaptel-1.2.3 and a PRI with 8 voice
channels.
With nobody on the phone using ztmonitor I get the following:
Why would I have such high TX signals on certain channels.
~ron
[EMAIL PROTECTED] zaptel-1.2.3]# ./ztmonitor 1 -vv
Visual Audio Levels.
Hi,
I cannot get 'ztmonitor' to run anymore after I ran 'fxotune'. I get the
following error:
[EMAIL PROTECTED] ~]# cd /usr/src/zaptel
[EMAIL PROTECTED] zaptel]# ./ztmonitor 1 -
Unable to open /dev/dsp: No such file or directory
Cannot open audio ...
[EMAIL PROTECTED] zaptel]#
I am using
2005/11/18, Chuck Bunn [EMAIL PROTECTED]:
Hi,
I cannot get 'ztmonitor' to run anymore after I ran 'fxotune'. I get the
following error:
[EMAIL PROTECTED] ~]# cd /usr/src/zaptel
[EMAIL PROTECTED] zaptel]# ./ztmonitor 1 -
Unable to open /dev/dsp: No such file or directory
Cannot open
Hi,
Thanks that worked I was trying to get more details... apparently you
are only allowed 2 v's so both of these work.
./ztmonitor 1 -v
./ztmonitor 1 -vv
with the later giving more detail..
Thanks Again.
Adri Vidal wrote:
2005/11/18, Chuck Bunn [EMAIL PROTECTED]:
Hi,
I
I am trying to get ztmonitor to record a channel for me.
I issue the ./ztmonitor 1 -v -f channel1.rawcommand,
And the channel1.raw file is created, but when I exit the program
(control-c), the size of the *.raw file is 0 bytes.
The program does update the screen with the VU Meter interface,
Hello,
In my quest to figure out the source of the random echo on our shiny new
asterisk install, I have been using ztmonitor on the TDM400p channels
for the good part of today.
I have 2 TDM400p cards with 8 FXO modules and 6 pots lines connected to
them (last 2 channels are unused but configured
VaibhaV Sharma wrote:
Hello,
In my quest to figure out the source of the random echo on our shiny new
asterisk install, I have been using ztmonitor on the TDM400p channels
for the good part of today.
I have 2 TDM400p cards with 8 FXO modules and 6 pots lines connected to
them (last 2 channels
On Fri, 2005-08-26 at 12:37 -0500, Eric Wieling aka ManxPower wrote:
VaibhaV Sharma wrote:
Hello,
I have 2 TDM400p cards with 8 FXO modules and 6 pots lines connected to
them (last 2 channels are unused but configured in zaptel). Even when
the lines are onhook, the Tx values settle down
We just replaced our old system at work with Asterisk. We use a TDM
card with 3 FXO ports. In tuning my gains, I discovered that the
on-hook rx levels do in fact waver a little bit. Line 1 is right around
145, Line 2 is around 235, Line 3 is around 380, and Line 4, which
doesn't go to a POTS
If the RX has a constant 2 # marks when no one is on the phone, thats a bad
phone line, right?
(RX) (TX)
##*
Rx: 493 ( 496) Tx: 0 (0)
Good day list,
I am feeling extra stupid this Monday morning and am hoping
someone can come to the rescue.
I am trying to use the ztmonitor utility on my wildfire 4 FXO
card. and have read the following from the wiki.
*Wiki start
If you set this to yes, use
-users@lists.digium.com
Subject: [Asterisk-Users] ztmonitor
Good day list,
I am feeling extra stupid this Monday morning and am hoping
someone can come to the rescue.
I am trying to use the ztmonitor utility on my wildfire 4 FXO
card. and have read the following from the wiki
I have a x101p and I can't seem to get ztmonitor to work on it. I've
tried it on 2 different machines. One with a SBLive! card and the other
with a AMD-768 [Opus] Audio (rev 03) chip. Neither machine give me a
graph in ztmonitor 1 -v mode. If I run ztmonitor without the -v I
get:
Ah! I just checked out the latest ztmonitor out of cvs and it works
just fine.
...Jeff
On Mon, 2004-02-23 at 12:51, Jeff Gustafson wrote:
I have a x101p and I can't seem to get ztmonitor to work on it. I've
tried it on 2 different machines. One
try ztmonitor 1 -v
Martin
On Sat, 20 Dec 2003, Daniel Bichara wrote:
Hi,
I am trying to run ZTMonitor to get debug info from my E100P board but I
got the following message:
-bash-2.05b# ./ztmonitor 1
Unable to open /dev/dsp: No such file or directory
Cannot open audio ...
-bash-2.05b#
Well thats broken.. we have a bug on bugs.digium.com over this.
bkw
On Mon, 22 Dec 2003, Martin Pycko wrote:
try ztmonitor 1 -v
Martin
On Sat, 20 Dec 2003, Daniel Bichara wrote:
Hi,
I am trying to run ZTMonitor to get debug info from my E100P board but I
got the following message:
Hi,
I am trying to run ZTMonitor to get debug info from my E100P board but I
got the following message:
-bash-2.05b# ./ztmonitor 1
Unable to open /dev/dsp: No such file or directory
Cannot open audio ...
-bash-2.05b#
Thanks,
Daniel
___
ztmonitor 1 -v
On Sat, 20 Dec 2003, Daniel Bichara wrote:
Hi,
I am trying to run ZTMonitor to get debug info from my E100P board but I
got the following message:
-bash-2.05b# ./ztmonitor 1
Unable to open /dev/dsp: No such file or directory
Cannot open audio ...
-bash-2.05b#
Thanks,
29 matches
Mail list logo
