I have the following software installed in a Centos Box with a TE420 (5th Gen)
card.
. Centos 6.5 64-bit
. Asterisk 1.4.22
. dahdi-linux-complete-2.9.1.1+2.9.1
. libpri-1.4.14.
Even without plugging in the ISDN into span 1, all 4 spans are flashing red.
Plugging an E1 into span 1 makes no
Hi Rusty,
We found the problem - a configuration error. Thank you for the response.
On 29 May 2014 23:35, Rusty Newton rnew...@digium.com wrote:
On Thu, May 22, 2014 at 6:22 PM, David Cunningham
dcunning...@voisonics.com wrote:
Hello,
We have servers running Asterisk 1.8.20.1 and
On Fri, May 30, 2014 at 7:42 AM, David Cunningham
dcunning...@voisonics.com wrote:
Hi Rusty,
We found the problem - a configuration error. Thank you for the response.
I'm glad you found the issue! No problem.
--
Rusty Newton
Digium, Inc. | Community Support Manager
445 Jan Davis Drive NW -
Hi,
The issue is solved . I created voicemessages table in MySQL according to
Asterisk book. Just replace 'label' column with 'msg_id' in 'voicemessages'
table. Thank you.
Regards,
Thet Tun
On Thu, May 29, 2014 at 9:09 AM, ProNek pro...@gmail.com wrote:
Hi All,
I have an issue on voice
Hi Rusty,
Noted with thanks.
Regards,
Thet Tun
On Thu, May 29, 2014 at 5:09 PM, Rusty Newton rnew...@digium.com wrote:
On Thu, May 29, 2014 at 3:33 AM, ProNek pro...@gmail.com wrote:
Hi,
I have some issue with voice mail with ODBC on asterisk 11.7 box. I may
not
understand database
Hello,
Is there a way to configure Asterisk so that it doesn't care about the
playload type in SDP ?
I'm trying to send custom data which has assigned a dynamic PT through RTP
so I only need Asterisk to act as a proxy/forwarder but I'm getting 488
Not acceptable here responses and in console No
Nicolae Rosia wrote:
Hello,
Kia ora,
Is there a way to configure Asterisk so that it doesn't care about the
playload type in SDP ?
I'm trying to send custom data which has assigned a dynamic PT through
RTP so I only need Asterisk to act as a proxy/forwarder but I'm getting
488 Not acceptable
In this case I guess the only workaround is to load a module which
registers a codec specific to that payload type?
On Fri, May 30, 2014 at 6:46 PM, Joshua Colp jc...@digium.com wrote:
Nicolae Rosia wrote:
Hello,
Kia ora,
Is there a way to configure Asterisk so that it doesn't care
Nicolae Rosia wrote:
In this case I guess the only workaround is to load a module which
registers a codec specific to that payload type?
It actually requires modifying Asterisk in multiple places (format.h,
rtp_engine.c, frame.c, and others I'm probably forgetting). Adding
knowledge of a
On Fri, May 30, 2014 at 4:07 AM, Lee, John (Sydney)
john@compuware.com wrote:
Even without plugging in the ISDN into span 1, all 4 spans are flashing red.
Blinking red led is normal for spans which have been configured, but
are receiving no signal.
I might try plugging up a physical loopback
Hi,
I am using Asterisk 1.4 along with FreePBX.
My call flow is as follows:
Inbound DID Inbound Route Time Condition Queue.
My welcome greeting MP3 is setup under System Recordings its called
under Queue Join Announcement.
Not sure why, the MP3 audio file starts to play after a 5 sec
Hi ,
Can you post cli log
With regards
N.Prakash
--
From: RSCL Mumbai rscl.mum...@gmail.com
Sent: 30-05-2014 11:16 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
asterisk-users@lists.digium.com
Subject: [asterisk-users] Delay Before Join
12 matches
Mail list logo