Re: [beagleboard] Re: BBGW and Robotics Cape

My fork is located here. https://github.com/Andrewiski/Robotics_Cape_Installer Library compiles and I think I have the model detected and the pins excluded even in the pru0 but stuck on compiling my new overlays so I can test. Doing something stupid here I am sure but have never had to

Re: [beagleboard] Re: error messages on serial console during BBGW bootup

On Mon, Mar 27, 2017 at 12:08 PM, wrote: > I am also facing similar issues of not being able to boot the BBGW. Can you > recommend which debugger/cable did you use. I tries searching the net but > found only your page.

[beagleboard] Using prussdrv.h etc, from Eclipse LUNA IDE

Hi; I am hoping someone can help with my question. I am a HW engineer that is learning Linux and C programming on the BBB. I have done bare metal type programming on Microchip devices so this is a fairly big jump. I have code running that handles a nibble wide interface to a 4 x 20 LCD. Also

[beagleboard] Re: BBB CAN Baud Rate

What drivers/libraries have you used to get CAN working on the BeagleBone? Thanks, Brian On Monday, June 9, 2014 at 5:51:57 PM UTC-5, Edwin Silva wrote: > > I have the Beaglebone Black tested and working on a CAN bus at 33.766k. > At the moment, I do not have a way to test different baud

[beagleboard] Re: error messages on serial console during BBGW bootup

I am also facing similar issues of not being able to boot the BBGW. Can you recommend which debugger/cable did you use. I tries searching the net but found only your page. -Amit On Thursday, 8 September 2016 07:40:50 UTC-4, Stephane Charette wrote: > > The serial debug cable I ordered for my

[beagleboard] Re: Seed Grove MiCS-6814 and Python

Hi any luck with this ? I'm also trying to get to work on BB On Tuesday, 7 March 2017 20:15:11 UTC+4, Davide Aguiari wrote: > > Hi everyone. > I'm trying to read my Seed Grove Multichannel gas sensor. ( > http://wiki.seeed.cc/Grove-Multichannel_Gas_Sensor/) > I now, in the webpage the're a red X

Re: [beagleboard] Disabling PowerOff and Reset button

Thanks for the info. I tried to find the corresponding dtb to modify but no success :( I can't find any am335x-bone-common.dtb. Do you know where should I look ? Regards, PM Le lundi 27 mars 2017 15:14:37 UTC+2, Jason Kridner a écrit : > > > > On Mar 27, 2017, at 8:47 AM, Gerald Coley

Re: [beagleboard] Disabling PowerOff and Reset button

> On Mar 27, 2017, at 8:47 AM, Gerald Coley wrote: > > Reset pin goes to the reset line and the power button goes to the PMIC. PMIC > pins and reset lines are not controlled via the DTS file The interrupt into software for the power button is dts controlled:

[beagleboard] systemd-logind.service inactive (dead)

I am using kali linux. When I am booting it is showing [FAILED] Failed to start login service. I booted in safe mode. systemctl status systemd-logind.service is showing inactive(dead). No reason is provided. I tried enabling it with systemctl. But it is saying, no [INSTALL] section is

Re: [beagleboard] Disabling PowerOff and Reset button

Reset pin goes to the reset line and the power button goes to the PMIC. PMIC pins and reset lines are not controlled via the DTS file On Mon, Mar 27, 2017 at 5:02 AM, PM wrote: > Hello everybody, > > I am trying to disable my reset & poweroff button from my LCD7

[beagleboard] Disabling PowerOff and Reset button

Hello everybody, I am trying to disable my reset & poweroff button from my LCD7 cape. I saw on the schematic diagram that these buttons are directly connected to SYS_RESET & PWR_BUT. I would like to know if it is possible to disable these buttons by editing any 'dts' or 'dtso' file ? Thank

Re: [beagleboard] dtbo edition does not work

Thank you it works perfectly :) Le vendredi 24 mars 2017 20:22:43 UTC+1, RobertCNelson a écrit : > > On Fri, Mar 24, 2017 at 11:26 AM, PM > wrote: > > Hello, > > > > I am currently using a Beaglebone Black with these distribution : > > > > Distributor ID:Debian