Hi Williams,
Thanks for your email.
Earlier message on the calling hq-phones was not enough bandwidth when i
tried to place the call to 4220, after reload whole lab now its Ring out
and fast busy. When i dial 4 digit extension of BR2 phone from HQ or BR1
phone call goes smooth no prob upto 4
Hi Experts,
I got my problem solved buy reloading the br2-config , publisher and
subscriber.
can you please advise me how to tackle the requirement of reload in CCIE
Lab exam
this is very important for me because my Presence also donot work unless i
restart my whole lab
please advice...
)
--
Message: 1
Date: Fri, 22 Mar 2013 16:17:09 +0300
From: Vikky Kumar vikkyne...@gmail.com
To: Sears, Michael (msears) michael.se...@compucom.com
Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] HQ and Branch1 phones cannot call CUE
Message-ID
CUE only does G711, do you have a transcoder?
Sent from my iPhone
On Mar 20, 2013, at 12:39 PM, Vikky Kumar vikkyne...@gmail.com wrote:
Hi Experts,
I configured branch 2 CME/CUE working normal for Voice mails.
CUE is registered with CUCM but I call not call CUE(6220) from HQ and
Check the codecs, transcoders, MRG, MRGL, etc
On Wed, Mar 20, 2013 at 11:16 AM, Vikky Kumar vikkyne...@gmail.com wrote:
Hi Experts,
I configured branch 2 CME/CUE working normal for Voice mails.
CUE is registered with CUCM but I call not call CUE(6220) from HQ and
Branch1 but branch2
Hi,
You have to add on your CME side.
voice service voip
allow connection h t h
allow connection h t s
allow connection s t h
Thanks,
Ramcharan Arya
On Wed, Mar 20, 2013 at 1:16 PM, Vikky Kumar vikkyne...@gmail.com wrote:
Hi Experts,
I configured branch 2 CME/CUE working normal for
Hi Experts,
I have configured :
1. transcoder on CUCM for HQ BR2 (Cisco IOS Enhanced Media Termination
Point )
and also Router of BR2 (dspfarm profile 2 transcode , max sess 4 .. )
2. above hq-xcode,, sc-xcode is registered included in respective mrg
mrgl DP
3. voice service voip ,
Hi,
You need to add codec g729r8 in your transcoder profile.
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30
Codec : g711alaw, Maximum Packetization Period : 30
Codec : g729ar8, Maximum Packetization Period : 60
Codec : g729abr8, Maximum Packetization Period : 60
Ram,
I added g729r8 but with no luck.
Regards,
On Wed, Mar 20, 2013 at 10:51 PM, Ramcharan Arya
ramcharan.a...@gmail.comwrote:
Hi,
You need to add codec g729r8 in your transcoder profile.
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30
Codec : g711alaw,
Vikky,
Please clarify. You say you have configured Branch 2 as CME and CUE. Then you
say CUE is registered to CUCM. That doesn't jive for me. Perhaps I am
mis-reading or mis-interpreting that part of the question.
You also say you are doing CAC between HQ and Branch 2. Is this locations based
Willam,
BR2 is CUCM site, and there is integration b/w CUE - CUCM
I have configured RSVP, rsvp bandwidth = 136 kbps on both sides
When i call HQ phone to BR2-CUE it gives fast busy tone and give Ring out
display on HQ Phones
pt. b. transcoder in a MRG and MRGL that is assigned to CUE CTI
I advise against using codec pass through on the MTP. I'd recommend something
like the following:
dspfarm profile 2 mtp
no codec g711u
codec g729r8
max sess softw some number
assoc app sccp
no shut
dspfarm profile 3 transcod
codec g729r8
max sess some number
assoc app sccp
no shut
!
ccm
Greetings Vikas,
First, do you get any message on the calling phone, like not enough bandwidth
when you try and place the call. What happens when you try and dial 4 digit
extension of BR2 phone from HQ or BR1 phone, Rapid busy, dead air, not enough
bandwidth on display of phone, Rerouting?
13 matches
Mail list logo