Dear All,
I am facing issue in opening the PDF workbook and accessing my account in
ipexpert today.
I tried to send e-mail to supp...@ipexpert.com but still waiting for the
answer.
Just wanted to ensure if this problem exists only for me or to every
ipexpert customer.
Thanks,
Viki
I need help to reslove the problem with TEI_ASSIGNED on the T1 Link ISDN Serial0/0/0:23 interface dsl 0, interface ISDN Switchtype = primary-ni L2 Protocol = Q.921 0x L3 Protocol(s) = CCM MANAGER 0x0003 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
CorpHQ#CorpHQ#ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSEISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSECorpHQ#CorpHQ#ISDN Se0/0/0:23 Q921: User RX -
Has anybody had issues powering up phones when using the NM-ESW-16? I have
two phones on my BR1 router, 7940 and a 7961. The 7940 is running a SIP
load and powers on fine, but the 7961 running a SCCP load will not power on
at all. I'm running firmware version 9-3-1SR2-1S. Any help would be
Hi,
I am able to access my account and able to open workbook successfully.
Have you updated your Adobe reader recently if yes then you might have to
install correct fileopen plug-in.
Thanks,
Ramcharan Arya CCIE # 28926(Voice/Routing Switching)
On Sat, Oct 5, 2013 at 8:04 AM, Vignesh
Hello Guys,
I have the following questions for MVA.
1) I am
followingnbsp; a 4 digitnbsp; internal dial-plan fornbsp; my site B
phonesnbsp; and
there is a requirement that I usenbsp; 3033300nbsp; ( 7 digit number )nbsp;
as my
MVA numbernbsp;nbsp; thennbsp; can strip this 7 digit number
I'm working on the OWLE Lab 1 Section 4.3. I'm having difficulty getting the
phone to display To +1408 when goes out either Site B H323 gateway or Site C
H323 gateway. I'm doing my digit manipulation at the RL list with a predot to
remove the 9 at each of the gatways. Thanks for your help.
Inbound voip dial peers on h323 gateways strip the +. You have to use something
on the gateway itself (such as voice translation rules) to add the + back to
the call.
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Ryan Maxam
Sent:
Not impossible - just takes extra steps. You are right, you can do calling
party transformations on the gateways, but those will affect all calls, not
just cfur calls.
To be safe, you can add an extra step in the outbound call flow to tag the
cfur call. You can have your cfur css point to a
Did you try the steps I outlined earlier?
Does show ccm indicate your mgcp gw is regisyered to cucm? If not check
your hostname and domain name (if set) on gw and double check the cucm
config.
If so it is registered you could take it a step further and remove the
pri-group from the controller
You will not be able to bring up the pri until your mgcp gw registers to
cucm. In my very first reply I assumed it was already registered but I
guess I should have asked.
The most common reason for not registering is a mismatch on hostname. The
gateway will register as either hostname (if ip
Guys,
Any update?
From: rameshlt;rameshdol...@rediffmail.comgt;
Sent: Sat, 05 Oct 2013 20:12:14
To: ccie_voice@onlinestudylist.comlt;ccie_voice@onlinestudylist.comgt;
Subject: MVA confusion and quesiton
Hello Guys,
I have the following questions for MVA.
1) I am
followingnbsp; a 4
12 matches
Mail list logo
