[OSL | CCIE_Voice] Issues in opening the workbook and accessing my account
Dear All, I am facing issue in opening the PDF workbook and accessing my account in ipexpert today. I tried to send e-mail to supp...@ipexpert.com but still waiting for the answer. Just wanted to ensure if this problem exists only for me or to every ipexpert customer. Thanks, Viki ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] TEI_ASSIGNED
I need help to reslove the problem with TEI_ASSIGNED on the T1 Link ISDN Serial0/0/0:23 interface dsl 0, interface ISDN Switchtype = primary-ni L2 Protocol = Q.921 0x L3 Protocol(s) = CCM MANAGER 0x0003 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 0 CCBs = 0 The Free Channel Mask: 0x8007 Number of L2 Discards = 0, L2 Session ID = 0 Total Allocated ISDN CCBs = 0CorpHQ# CorpHQ#show runBuilding configuration...Current configuration : 3755 bytes!! Last configuration change at 23:30:37 PDT Fri Oct 4 2013! NVRAM config last updated at 23:30:39 PDT Fri Oct 4 2013!version 12.4no service padno service timestamps debug uptimeno service timestamps log uptimeno service password-encryption!hostname CorpHQ!boot-start-markerboot-end-marker!logging message-counter syslogenable secret 5 $1$QYKS$Z.r9xOUE1ga6IkB6fi3QU0!no aaa new-modelclock timezone PST -8clock summer-time PDT recurringnetwork-clock-participate wic 0 network-clock-select 1 T1 0/0/0!dot11 syslogip source-route!!ip cef!!no ip domain lookupip multicast-routing no ipv6 cef!multilink bundle-name authenticatedisdn switch-type primary-ni!!!voice service voip sip bind control source-interface Loopback0 bind media source-interface Loopback0voice-card 0!!! !!archivelog config hidekeys! controller T1 0/0/0cablelength short 133pri-group timeslots 1-3,24 service mgcpdescription == Voice Circuit to PSTN!controller T1 0/0/1cablelength short 133channel-group 0 timeslots 1-24description == Data Circuit to WAN!ip tcp synwait-time 5!! !!interface Loopback0ip address 177.1.254.1 255.255.255.255!interface FastEthernet0/0description == To SW1no ip addressduplex autospeed auto!interface FastEthernet0/0.10description == Server VLANencapsulation dot1Q 10ip address 177.1.10.1 255.255.255.0ip pim dense-modeip tcp adjust-mss 1300!interface FastEthernet0/0.11description == Voice VLANencapsulation dot1Q 11ip address 177.1.11.1 255.255.255.0ip pim dense-modeip tcp adjust-mss 1300!interface FastEthernet0/0.12description == Data VLANencapsulation dot1Q 12ip address 177.1.12.1 255.255.255.0ip tcp adjust-mss 1300!interface FastEthernet0/0.13description == PSTN PHONE VLANencapsulation dot1Q 13ip address 177.1.13.1 255.255.255.0ip tcp adjust-mss 1300!interface FastEthernet0/1description === To PSTNip address 177.1.19.254 255.255.255.0duplex autospeed auto!interface Serial0/0/0:23no ip addressencapsulation hdlcisdn switch-type primary-niisdn incoming-voice voiceisdn bind-l3 ccm-managerno cdp enable!interface Serial0/0/1:0description == Frame-Relay Circuit to WANno ip addressencapsulation frame-relaycdp enableno frame-relay inverse-arpframe-relay lmi-type ansi!interface Serial0/0/1:0.1 point-to-pointdescription == FR To BR1ip address 177.0.101.1 255.255.255.0ip pim dense-modesnmp trap link-statusframe-relay interface-dlci 101 !interface Serial0/0/1:0.2 point-to-pointdescription == FR To BR2ip address 177.0.201.1 255.255.255.0ip pim dense-modesnmp trap link-statusframe-relay interface-dlci 201 !router ospf 1log-adjacency-changesnetwork 0.0.0.0 255.255.255.255 area 0!ip forward-protocol ndip http serverno ip http secure-server!!!cdp timer 6!!!control-plane!!!voice-port 0/0/0:23!ccm-manager redundant-host 177.1.10.10ccm-manager mgcp codec-allccm-manager fax protocol ciscoccm-manager music-on-hold!mgcpmgcp call-agent 177.1.10.20 service-type mgcp version 0.1mgcp dtmf-relay voip codec all mode out-of-bandmgcp fax t38 ecmmgcp bind control source-interface Loopback0mgcp bind media source-interface Loopback0!mgcp profile default! !gatekeepershutdown!!line con 0exec-timeout 0 0privilege level 15logging synchronous level 0 limit 20line aux 0line vty 0 4exec-timeout 0 0privilege level 15password ciscologging synchronousno loginline vty 5 15exec-timeout 0 0privilege level 15logging synchronousno login!scheduler allocate 2 1000ntp source Loopback0ntp master 13ntp server 177.1.254.254endCorpHQ#show isdn stGlobal ISDN Switchtype = primary-ni%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not applyISDN Serial0/0/0:23 interface dsl 0, interface ISDN Switchtype = primary-ni L2 Protocol = Q.921 0x L3 Protocol(s) = CCM MANAGER 0x0003 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 0 CCBs = 0 The Free Channel Mask: 0x8007 Number of L2 Discards = 0, L2 Session ID = 0 Total Allocated ISDN CCBs = 0CorpHQ# ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] TEI_ASSIGNED
CorpHQ#CorpHQ#ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSEISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSECorpHQ#CorpHQ#ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSECorpHQ#CorpHQ#ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSECorpHQ#CorpHQ#ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSECorpHQ#CorpHQ#ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSECorpHQ#CorpHQ# I need help to reslove the problem with TEI_ASSIGNED on the T1 Link ISDN Serial0/0/0:23 interface dsl 0, interface ISDN Switchtype = primary-ni L2 Protocol = Q.921 0x L3 Protocol(s) = CCM MANAGER 0x0003 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 0 CCBs = 0 The Free Channel Mask: 0x8007 Number of L2 Discards = 0, L2 Session ID = 0 Total Allocated ISDN CCBs = 0CorpHQ# CorpHQ#show runBuilding configuration...Current configuration : 3755 bytes!! Last configuration change at 23:30:37 PDT Fri Oct 4 2013! NVRAM config last updated at 23:30:39 PDT Fri Oct 4 2013!version 12.4no service padno service timestamps debug uptimeno service timestamps log uptimeno service password-encryption!hostname CorpHQ!boot-start-markerboot-end-marker!logging message-counter syslogenable secret 5 $1$QYKS$Z.r9xOUE1ga6IkB6fi3QU0!no aaa new-modelclock timezone PST -8clock summer-time PDT recurringnetwork-clock-participate wic 0 network-clock-select 1 T1 0/0/0!dot11 syslogip source-route!!ip cef!!no ip domain lookupip multicast-routing no ipv6 cef!multilink bundle-name authenticatedisdn switch-type primary-ni!!!voice service voip sip bind control source-interface Loopback0 bind media source-interface Loopback0voice-card 0!!! !!archivelog config hidekeys! controller T1 0/0/0cablelength short 133pri-group timeslots 1-3,24 service mgcpdescription == Voice Circuit to PSTN!controller T1 0/0/1cablelength short 133channel-group 0 timeslots 1-24description == Data Circuit to WAN!ip tcp synwait-time 5!! !!interface Loopback0ip address 177.1.254.1 255.255.255.255!interface FastEthernet0/0description == To SW1no ip addressduplex autospeed auto!interface FastEthernet0/0.10description == Server VLANencapsulation dot1Q 10ip address 177.1.10.1 255.255.255.0ip pim dense-modeip tcp adjust-mss 1300!interface FastEthernet0/0.11description == Voice VLANencapsulation dot1Q 11ip address 177.1.11.1 255.255.255.0ip pim dense-modeip tcp adjust-mss 1300!interface FastEthernet0/0.12description == Data VLANencapsulation dot1Q 12ip address 177.1.12.1 255.255.255.0ip tcp adjust-mss 1300!interface FastEthernet0/0.13description == PSTN PHONE VLANencapsulation dot1Q 13ip address 177.1.13.1 255.255.255.0ip tcp adjust-mss 1300!interface FastEthernet0/1description === To PSTNip address 177.1.19.254 255.255.255.0duplex autospeed auto!interface Serial0/0/0:23no ip addressencapsulation hdlcisdn switch-type primary-niisdn incoming-voice voiceisdn bind-l3 ccm-managerno cdp enable!interface Serial0/0/1:0description == Frame-Relay Circuit to WANno ip addressencapsulation frame-relaycdp enableno frame-relay inverse-arpframe-relay lmi-type ansi!interface Serial0/0/1:0.1 point-to-pointdescription == FR To BR1ip address 177.0.101.1 255.255.255.0ip pim dense-modesnmp trap link-statusframe-relay interface-dlci 101 !interface Serial0/0/1:0.2 point-to-pointdescription == FR To BR2ip address 177.0.201.1 255.255.255.0ip pim dense-modesnmp trap link-statusframe-relay interface-dlci 201 !router ospf 1log-adjacency-changesnetwork 0.0.0.0 255.255.255.255 area 0!ip forward-protocol ndip http serverno ip http secure-server!!!cdp timer 6!!!control-plane!!!voice-port 0/0/0:23!ccm-manager redundant-host 177.1.10.10ccm-manager mgcp codec-allccm-manager fax protocol ciscoccm-manager music-on-hold!mgcpmgcp call-agent 177.1.10.20 service-type mgcp version 0.1mgcp dtmf-relay voip codec all mode out-of-bandmgcp fax t38 ecmmgcp bind control source-interface Loopback0mgcp bind media source-interface Loopback0!mgcp profile default! !gatekeepershutdown!!line con 0exec-timeout 0 0privilege level 15logging synchronous level 0 limit 20line aux 0line vty 0 4exec-timeout 0 0privilege level 15password ciscologging synchronousno loginline vty 5 15exec-timeout 0 0privilege level 15logging synchronousno login!scheduler allocate 2 1000ntp source Loopback0ntp master 13ntp server 177.1.254.254endCorpHQ#show isdn stGlobal ISDN Switchtype = primary-ni%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not applyISDN Serial0/0/0:23 interface dsl 0, interface ISDN Switchtype =
[OSL | CCIE_Voice] Issues powering up phones with the NM-ESW-16
Has anybody had issues powering up phones when using the NM-ESW-16? I have two phones on my BR1 router, 7940 and a 7961. The 7940 is running a SIP load and powers on fine, but the 7961 running a SCCP load will not power on at all. I'm running firmware version 9-3-1SR2-1S. Any help would be much appreciated. Bill ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Issues in opening the workbook and accessing my account
Hi, I am able to access my account and able to open workbook successfully. Have you updated your Adobe reader recently if yes then you might have to install correct fileopen plug-in. Thanks, Ramcharan Arya CCIE # 28926(Voice/Routing Switching) On Sat, Oct 5, 2013 at 8:04 AM, Vignesh Sethuraman sethuvign...@gmail.comwrote: Dear All, I am facing issue in opening the PDF workbook and accessing my account in ipexpert today. I tried to send e-mail to supp...@ipexpert.com but still waiting for the answer. Just wanted to ensure if this problem exists only for me or to every ipexpert customer. Thanks, Viki ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] MVA confusion and quesiton
Hello Guys, I have the following questions for MVA. 1) I am followingnbsp; a 4 digitnbsp; internal dial-plan fornbsp; my site B phonesnbsp; and there is a requirement that I usenbsp; 3033300nbsp; ( 7 digit number )nbsp; as my MVA numbernbsp;nbsp; thennbsp; can strip this 7 digit number tonbsp; the last 4 digitnbsp; number (nbsp; 3300 ) as my MVA number ? 2) Alsonbsp; my calling number isnbsp; a 7 digit number coming from pstnnbsp; as 525nbsp; then do I change it to 9525? 3) If incase calling number isnbsp; a 10 digit numbernbsp; then It would come into site B as 972525 ( which is 10 digits) is manipulation required for this or can I just use the complete match with 10 digits on the service parameter level? -Ramesh Dollar ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Phone Display To +1408
I'm working on the OWLE Lab 1 Section 4.3. I'm having difficulty getting the phone to display To +1408 when goes out either Site B H323 gateway or Site C H323 gateway. I'm doing my digit manipulation at the RL list with a predot to remove the 9 at each of the gatways. Thanks for your help. Ryan Maxam Manager, Project Engineering CCNP CCVP CCDP Phone: 813-418-8035 Cell: 813-263-9346 TeleCommunication Systems, Inc. Sent from my iPad___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Phone Display To +1408
Inbound voip dial peers on h323 gateways strip the +. You have to use something on the gateway itself (such as voice translation rules) to add the + back to the call. From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Ryan Maxam Sent: Saturday, October 05, 2013 10:19 AM To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Phone Display To +1408 I'm working on the OWLE Lab 1 Section 4.3. I'm having difficulty getting the phone to display To +1408 when goes out either Site B H323 gateway or Site C H323 gateway. I'm doing my digit manipulation at the RL list with a predot to remove the 9 at each of the gatways. Thanks for your help. Ryan Maxam Manager, Project Engineering CCNP CCVP CCDP Phone: 813-418-8035tel:813-418-8035 Cell: 813-263-9346tel:813-263-9346 TeleCommunication Systems, Inc. Sent from my iPad Important Notice: This email message and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you are not the named addressee, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of Core BTS. Core BTS specifically disclaims liability for any damage caused by any virus transmitted by this email. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CFUR vs Calling Party Transformation on MGCP gateway
Not impossible - just takes extra steps. You are right, you can do calling party transformations on the gateways, but those will affect all calls, not just cfur calls. To be safe, you can add an extra step in the outbound call flow to tag the cfur call. You can have your cfur css point to a translation pattern that can pre-pend some sort of identification code (such as **) on the front of the calling number. Then that translation pattern can forward the call to your normal cfur route patterns/gateways. On the gateways then, you can have then have the calling party transformations only operate on the numbers that start with ** Since the translation pattern can be based on your called number, with this method you are able to manipulate the calling number based on the called number. Cliff From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Somphol Boonjing Sent: Friday, October 04, 2013 11:26 PM To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] CFUR vs Calling Party Transformation on MGCP gateway Hi All, Am I understand correctly that unlike voice translation profile on IOS gateway, the calling party translation pattern, that is applied to gateway level for outgoing call, can't be tailored based on destination route pattern? For example, assuming both Site B and Site C are in SRST mode, for outgoing call originating to Site B and Site C number based on CFUR, there is no way to tailor the calling party number so that the calling number is 10D for call going to Site B and 11D for call going to Site C. If Site A gateway is H323 because these can be customized using voice translation profile, but this would be particularly impossible if Site A gateway is MGCP. Regards, --Somphol. Important Notice: This email message and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you are not the named addressee, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of Core BTS. Core BTS specifically disclaims liability for any damage caused by any virus transmitted by this email. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] TEI_ASSIGNED
Did you try the steps I outlined earlier? Does show ccm indicate your mgcp gw is regisyered to cucm? If not check your hostname and domain name (if set) on gw and double check the cucm config. If so it is registered you could take it a step further and remove the pri-group from the controller (and essentially all pri and mgcp config) reboot, then put it all back. Also, if this is your home lab (or if you have access) what does the pstn side of the pri config look like? Make both sides have the same isdn switch-type and the pstn side has isdn protocol-emulate network under serial interface. A reload of both routers wouldn't hurt either (before or after all the above). Some links that may help: http://goo.gl/QA6qaC http://goo.gl/1ctXWS On Oct 5, 2013 10:03 AM, Anthony Nwachukwu anwachu...@apafrica.com wrote: CorpHQ#CorpHQ# ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0 ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSE ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0 ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSE CorpHQ#CorpHQ# ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0 ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSE CorpHQ#CorpHQ# ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0 ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSE CorpHQ#CorpHQ# ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0 ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSE CorpHQ#CorpHQ# ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0 ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSE CorpHQ#CorpHQ# I need help to reslove the problem with TEI_ASSIGNED on the T1 Link ISDN Serial0/0/0:23 interface dsl 0, interface ISDN Switchtype = primary-ni L2 Protocol = Q.921 0x L3 Protocol(s) = CCM MANAGER 0x0003 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 0 CCBs = 0 The Free Channel Mask: 0x8007 Number of L2 Discards = 0, L2 Session ID = 0 Total Allocated ISDN CCBs = 0 CorpHQ# CorpHQ#show run Building configuration... Current configuration : 3755 bytes ! ! Last configuration change at 23:30:37 PDT Fri Oct 4 2013 ! NVRAM config last updated at 23:30:39 PDT Fri Oct 4 2013 ! version 12.4 no service pad no service timestamps debug uptime no service timestamps log uptime no service password-encryption ! hostname CorpHQ ! boot-start-marker boot-end-marker ! logging message-counter syslog enable secret 5 $1$QYKS$Z.r9xOUE1ga6IkB6fi3QU0 ! no aaa new-model clock timezone PST -8 clock summer-time PDT recurring network-clock-participate wic 0 network-clock-select 1 T1 0/0/0 ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup ip multicast-routing no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-ni ! ! ! voice service voip sip bind control source-interface Loopback0 bind media source-interface Loopback0 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! voice-card 0 ! ! ! ! ! archive log config hidekeys ! ! ! ! ! controller T1 0/0/0 cablelength short 133 pri-group timeslots 1-3,24 service mgcp description == Voice Circuit to PSTN ! controller T1 0/0/1 cablelength short 133 channel-group 0 timeslots 1-24 description == Data Circuit to WAN ! ip tcp synwait-time 5 ! ! ! ! interface Loopback0 ip address 177.1.254.1 255.255.255.255 ! interface FastEthernet0/0 description == To SW1 no ip address duplex auto speed auto ! interface FastEthernet0/0.10 description == Server VLAN encapsulation dot1Q 10 ip address 177.1.10.1 255.255.255.0 ip pim dense-mode ip tcp adjust-mss 1300 ! interface FastEthernet0/0.11 description == Voice VLAN encapsulation dot1Q 11 ip address 177.1.11.1 255.255.255.0 ip pim dense-mode ip tcp adjust-mss 1300 ! interface FastEthernet0/0.12 description == Data VLAN encapsulation dot1Q 12 ip address 177.1.12.1 255.255.255.0 ip tcp adjust-mss 1300 ! interface FastEthernet0/0.13 description == PSTN PHONE VLAN encapsulation dot1Q 13 ip address 177.1.13.1 255.255.255.0 ip tcp adjust-mss 1300 ! interface FastEthernet0/1 description === To PSTN ip address 177.1.19.254 255.255.255.0 duplex auto speed auto ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn bind-l3 ccm-manager no cdp enable ! interface Serial0/0/1:0 description == Frame-Relay Circuit to WAN no ip address encapsulation frame-relay cdp enable no frame-relay inverse-arp frame-relay lmi-type ansi ! interface Serial0/0/1:0.1 point-to-point description == FR To BR1 ip address 177.0.101.1 255.255.255.0 ip pim dense-mode snmp trap
Re: [OSL | CCIE_Voice] TEI_ASSIGNED
You will not be able to bring up the pri until your mgcp gw registers to cucm. In my very first reply I assumed it was already registered but I guess I should have asked. The most common reason for not registering is a mismatch on hostname. The gateway will register as either hostname (if ip domain-name not set) or hostname.domain.com (if ip domain-name domain.com). I see your hostname is CorpHQ and I didn't see the ip domain-name command in yiur posted config. In this case make sure that in cucm you list the mgcp gw as CorpHQ exactly (I always type in the correct/matching case, I'm not sure if it is actually case sensitive but why take that chance?) Use show inventory on the router and make sure cucm has the correct router model and nm/wic part numbers. If still no luck (just looking at cucm), then delete the gw in cucm and recreate it. On the gateway use ccm config server [pub ip] and ccm config to tell the gateway to download the config from cucm. After it registers you can the no ccm config and make the pri fractional. For some basics, can you ping cucm pub and sub from the gateway? Can you ping from cucm cli to the gw lo0 ip? Do you have any qos? If yes remove qos temporarily to make sure that isn't interfering. If, after all this it still doesn't work, you should take a look at router debugs and cucm traces to determine if its a config issue or a network path issue. If debugs/traces don't show any traffic you could also run a packet capture on both router and cucm to see if you are getting any traffic at all between gw and cucm. On Oct 5, 2013 2:36 PM, Anthony Nwachukwu anwachu...@accesspointafrica.com wrote: Now see how far I have gone. Stil have issues with Registration with CCM and the second backup is none. ** ** ** ** CorpHQ#show ccm-manager MGCP Domain Name: CorpHQ PriorityStatus Host Primary None First BackupRegistering with CM 177.1.10.10 Second Backup None ** ** Current active Call Manager:None Backhaul/Redundant link port: 2428 Failover Interval: 30 seconds Keepalive Interval: 15 seconds Last keepalive sent:23:10:43 PDT Oct 4 2013 (elapsed time: 05:12:56) Last MGCP traffic time: 04:23:16 PDT Oct 5 2013 (elapsed time: 00:00:23) Last failover time: 03:57:15 PDT Oct 5 2013 from (0.0.0.0) Last switchback time: 03:57:06 PDT Oct 5 2013 from (177.1.10.20) Switchback mode:Immediate MGCP Fallback mode: Not Selected Last MGCP Fallback start time: None Last MGCP Fallback end time:None MGCP Download Tones:Disabled TFTP retry count to shut Ports: 2 ** ** Backhaul Link info: Link Protocol: TCP Remote Port Number: 2428 Remote IP Address: 177.1.10.10 Current Link State: OPEN Statistics: Packets recvd: 0 Recv failures: 0 Packets xmitted: 0 Xmit failures: 0 PRI Ports being backhauled: Slot 0, VIC 0, port 0 FAX mode: cisco Configuration Error History: CorpHQ# ** ** *From:* Justin Carney [mailto:justin.s.car...@gmail.com] *Sent:* 05 October 2013 18:55 *To:* Anthony Nwachukwu *Cc:* ccie_voice@onlinestudylist.com, (ccie_voice@onlinestudylist.com) *Subject:* Re: [OSL | CCIE_Voice] TEI_ASSIGNED ** ** Did you try the steps I outlined earlier? Does show ccm indicate your mgcp gw is regisyered to cucm? If not check your hostname and domain name (if set) on gw and double check the cucm config. If so it is registered you could take it a step further and remove the pri-group from the controller (and essentially all pri and mgcp config) reboot, then put it all back. Also, if this is your home lab (or if you have access) what does the pstn side of the pri config look like? Make both sides have the same isdn switch-type and the pstn side has isdn protocol-emulate network under serial interface. A reload of both routers wouldn't hurt either (before or after all the above). Some links that may help: http://goo.gl/QA6qaC http://goo.gl/1ctXWS On Oct 5, 2013 10:03 AM, Anthony Nwachukwu anwachu...@apafrica.com wrote: CorpHQ#CorpHQ# ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0 ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSE ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0 ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSE CorpHQ#CorpHQ# ISDN Se0/0/0:23 Q921: User RX - SABMEp sapi=0 tei=0 ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED vsc_wants_L2_up = FALSE CorpHQ#CorpHQ# ISDN Se0/0/0:23 Q921: User RX - SABMEp
Re: [OSL | CCIE_Voice] MVA confusion and quesiton
Guys, Any update? From: rameshlt;rameshdol...@rediffmail.comgt; Sent: Sat, 05 Oct 2013 20:12:14 To: ccie_voice@onlinestudylist.comlt;ccie_voice@onlinestudylist.comgt; Subject: MVA confusion and quesiton Hello Guys, I have the following questions for MVA. 1) I am followingnbsp; a 4 digitnbsp; internal dial-plan fornbsp; my site B phonesnbsp; and there is a requirement that I usenbsp; 3033300nbsp; ( 7 digit number )nbsp; as my MVA numbernbsp;nbsp; thennbsp; can strip this 7 digit number tonbsp; the last 4 digitnbsp; number (nbsp; 3300 ) as my MVA number ? 2) Alsonbsp; my calling number isnbsp; a 7 digit number coming from pstnnbsp; as 525nbsp; then do I change it to 9525? 3) If incase calling number isnbsp; a 10 digit numbernbsp; then It would come into site B as 972525 ( which is 10 digits) is manipulation required for this or can I just use the complete match with 10 digits on the service parameter level? -Ramesh Dollar Get your own FREE website, FREE domain amp; FREE mobile app with Company email. nbsp;Know More gt; ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
