Re: [OSL | CCIE_Voice] Can't dial from CME to CUCM
All calls from the CUCM to the CME go through the problem is on the CME site. I will run some debug on the CME and see which dial-peer it is using Thanks, Ben Date: Sat, 12 Jul 2014 09:48:08 -0400 Subject: Re: [OSL | CCIE_Voice] Can't dial from CME to CUCM From: justin.s.car...@gmail.com To: benjoh...@hotmail.com CC: ccie_voice@onlinestudylist.com You should check dialed number analyzer (https://pub-ip/DNA) to check the cucm if it will route the call from the gateway to the dn. In dna use the 'gateway' option, pick the vgw, and enter a dn you're trying to call. If dna says it will route then you need to focus on the cme side, or if it doesn't roite then focus on cucm side. Without seeing more details about your config I will recommend two thing: 1. Run debugs on cme router to ensure you're matching the dial peer and sending to cucm. 2. Check the css that is applied to the vgw and ensure that css has the partition(s) that contain your DNs. -Justin (Sent from my phone, please excuse and/or laugh at any typos.) On Jul 12, 2014 9:32 AM, "Ben John" wrote: Hello everyone, I connected my CUCM with my CME using H.323 gateway. I am facing a little bit challenge i can dial from CUCM to CME but i can't dial from CME to CUCM. I am using 4 digits dialing between both sites on the call manager i created RG using the H.323 gateway i created in the callmanager a RL pointing to gateway and a RP using that RL i also created DP,Region,LOC, etc... On the CUCM my RP looks like this: 6. with a predot On the gateway incoming calls is set to 4 When dial 6 + last 4 digits extension on the CME the phone rings. The challenge is that we have one HQ with and two remote sites all of them under on cluster one PUB and two SUBs the HQ and one remote site register with SUB1 as primary, SUB2 secondary and PUB last the other remote site register with SUB2 as pri, SUB1 as sec and PUB last all three site have different DNs and different area code. HQ last 4 digits start with 7 Remote 1 DNs start with 0 Remote 2 DNs start with 2,4,5,8 and also has two separate area code my configuration on the CME looks like this: This dial-peer go to HQ and Remote 1 dial-peer voice 2000 voip description calls to HQ and Remote 1 destination-pattern ^[0,7]...$ session target ipv4:100.260.129.21 dtmf-relay h245-alphanumeric no vad This dial-peer go to Remote 2 dial-peer voice 3000 voip description calls to Remote 2 destination-pattern ^[2,4,5,8]...$ session target ipv4:100.260.152.20 dtmf-relay h245-alphanumeric no vad When someone call from CME to CUCM the calls die. i am not using any translation pattern i think i don't need one Any idea what i am missing here ? Thanks, Ben ___ Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: iPexpert on YouTube: www.youtube.com/ipexpertinc ___ Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: iPexpert on YouTube: www.youtube.com/ipexpertinc
Re: [OSL | CCIE_Voice] Can't dial from CME to CUCM
You should check dialed number analyzer (https://pub-ip/DNA) to check the cucm if it will route the call from the gateway to the dn. In dna use the 'gateway' option, pick the vgw, and enter a dn you're trying to call. If dna says it will route then you need to focus on the cme side, or if it doesn't roite then focus on cucm side. Without seeing more details about your config I will recommend two thing: 1. Run debugs on cme router to ensure you're matching the dial peer and sending to cucm. 2. Check the css that is applied to the vgw and ensure that css has the partition(s) that contain your DNs. -Justin (Sent from my phone, please excuse and/or laugh at any typos.) On Jul 12, 2014 9:32 AM, "Ben John" wrote: > Hello everyone, > I connected my CUCM with my CME using H.323 gateway. I am facing a little > bit challenge i can dial from CUCM to CME but i can't dial from CME to > CUCM. I am using 4 digits dialing between both sites on the call manager i > created RG using the H.323 gateway i created in the callmanager a RL > pointing to gateway and a RP using that RL i also created DP,Region,LOC, > etc... > On the CUCM my RP looks like this: > 6. with a predot > On the gateway incoming calls is set to 4 > When dial 6 + last 4 digits extension on the CME the phone rings. > The challenge is that we have one HQ with and two remote sites all of them > under on cluster one PUB and two SUBs the HQ and one remote site register > with SUB1 as primary, SUB2 secondary and PUB last the other remote site > register with SUB2 as pri, SUB1 as sec and PUB last all three site have > different DNs and different area code. > HQ last 4 digits start with 7 > Remote 1 DNs start with 0 > Remote 2 DNs start with 2,4,5,8 and also has two separate area code > my configuration on the CME looks like this: > > This dial-peer go to HQ and Remote 1 > dial-peer voice 2000 voip > description calls to HQ and Remote 1 > destination-pattern ^[0,7]...$ > session target ipv4:100.260.129.21 > dtmf-relay h245-alphanumeric > no vad > > This dial-peer go to Remote 2 > dial-peer voice 3000 voip > description calls to Remote 2 > destination-pattern ^[2,4,5,8]...$ > session target ipv4:100.260.152.20 > dtmf-relay h245-alphanumeric > no vad > > When someone call from CME to CUCM the calls die. i am not using any > translation pattern i think i don't need one > > Any idea what i am missing here ? > > Thanks, > > Ben > > ___ > Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: > > iPexpert on YouTube: www.youtube.com/ipexpertinc > ___ Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: iPexpert on YouTube: www.youtube.com/ipexpertinc
[OSL | CCIE_Voice] Can't dial from CME to CUCM
Hello everyone, I connected my CUCM with my CME using H.323 gateway. I am facing a little bit challenge i can dial from CUCM to CME but i can't dial from CME to CUCM. I am using 4 digits dialing between both sites on the call manager i created RG using the H.323 gateway i created in the callmanager a RL pointing to gateway and a RP using that RL i also created DP,Region,LOC, etc... On the CUCM my RP looks like this: 6. with a predot On the gateway incoming calls is set to 4 When dial 6 + last 4 digits extension on the CME the phone rings. The challenge is that we have one HQ with and two remote sites all of them under on cluster one PUB and two SUBs the HQ and one remote site register with SUB1 as primary, SUB2 secondary and PUB last the other remote site register with SUB2 as pri, SUB1 as sec and PUB last all three site have different DNs and different area code. HQ last 4 digits start with 7 Remote 1 DNs start with 0 Remote 2 DNs start with 2,4,5,8 and also has two separate area code my configuration on the CME looks like this: This dial-peer go to HQ and Remote 1 dial-peer voice 2000 voip description calls to HQ and Remote 1 destination-pattern ^[0,7]...$ session target ipv4:100.260.129.21 dtmf-relay h245-alphanumeric no vad This dial-peer go to Remote 2 dial-peer voice 3000 voip description calls to Remote 2 destination-pattern ^[2,4,5,8]...$ session target ipv4:100.260.152.20 dtmf-relay h245-alphanumeric no vad When someone call from CME to CUCM the calls die. i am not using any translation pattern i think i don't need one Any idea what i am missing here ? Thanks, Ben ___ Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: iPexpert on YouTube: www.youtube.com/ipexpertinc