Can this be related to keepalive settings?
Do you have a keepalive line in your tunnel configuration? If you don't then it
means it's defaultly set to 10 seconds, try to put no keepalive
-Original Message-
From: cisco-nsp-boun...@puck.nether.net
I remember taking the whole core traffic down on a switch when trying a
deliberate and wrong use of ip local policy route-map due to lack of
experience and understanding. (sh*t happens)
So my suggestion is to do it carefully and understanding what exactly are you
trying to do... :-)
Anyone heard anything on PPPoA on the ASR 1000 series yet?
As far as i know it isn't supported (yet?) but i might be wrong :)
PPPoA would make it a superb replacement for our 720X series
We've been told it won't happen at least any time soon and to go with
10k as an upgrade path...
Not
Hi,
Is it possible to extend two vDCs between Data Centres using OTV (pair
of N7k on each site) - it's not clear how OTV uses vDCs to extend the
L2 domain.
Also, is it correct that Unicast-only transport support (and hence the
use of an Adjacency Server) is not supported initially (looking at
Hi James,
we are running wccp and when we configured squid to L2 Mask cpu
load returns to normal ~ 10%
Thank you!
BR
At 02:35 16/07/2010, James Baker wrote:
are you running wccp?
On Fri, Jul 16, 2010 at 10:47 AM, RAZAFINDRATSIFA Rivo Tahina
mailto:r.tah...@moov.mgr.tah...@moov.mg wrote:
Hi,
On Wed, Jul 21, 2010 at 07:33:56PM -0600, Quinn Kuzmich wrote:
To make this stranger, it's only ONE end of the tunnel going down.
The other side stays up.
That's not overly surprising as there is no signalling protocol on a GRE
tunnel (unless keepalives are configured) that could affect
Hi,
On Thu, Jul 22, 2010 at 10:01:04AM +0300, Ziv Leyes wrote:
Can this be related to keepalive settings?
Do you have a keepalive line in your tunnel configuration? If you don't then
it means it's defaultly set to 10 seconds, try to put no keepalive
There are no default keepalives on GRE
On 22/07/2010, at 8:16 PM, Matthew Melbourne wrote:
Is it possible to extend two vDCs between Data Centres using OTV (pair
of N7k on each site) - it's not clear how OTV uses vDCs to extend the
L2 domain.
yes, its possible. there are 3 methods:
1. OTV runs inside a Virtual Device Context.
On 21/07/2010 16:58, Chris Lane wrote:
I have a 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX on a 6509
You need to think of the 6148 as a set of 6 gigabit ethernet hubs, all
connected together by means of a single gigabit ethernet switch. If any of
the port groups microbursts to 1G
Ok, here's the config for one of the two routers - they have the same basic
HSRP config so if one is wrong, so is the other. Remember, the other end of
the tunnel is NOT exhibiting the problem at all.
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no
Howdy,
This isn't exactly cisco-centric, but it's certainly related
operationally.
I operate a county wide isp network and I have about 15 different
pops. I equip each with APC700/1400's and with XR battery packs, with
the goal being around 8 hours of runtime in the event of a power
On 7/22/2010 08:45, Mike wrote:
a) went berserk and flooded the network with garbage
b) issued spurious turn off ups commands to the ups
c) began automated self test cycles that shut off the ups (even when
self-test is disabled!)
I further have experienced UPSs that for
Has anyone seen any actual (real network) performance stats on Arista's 7500
flagship switch or have one in production? I cannot seem to find anyone who
has one of these boxes or any info on how they really perform under a load,
especially compared to the Nexus 7k (or even the 5k).
This
lookslike a good switch. But I haven't read too much articles neither the
datasheet.
I have found this document comparing switches manufacturers:
http://www.networkworld.com/community/node/57999
I'm interested in information about this switch too...
2010/7/22 Kevin Hatem kevin.ha...@pgs.com
Cisco has posted sxi4a.
Jared Mauch
On Jun 22, 2010, at 8:54 AM, Jared Mauch ja...@puck.nether.net wrote:
On Jun 22, 2010, at 8:42 AM, Gert Doering wrote:
Hi,
On Tue, Jun 22, 2010 at 08:03:22AM -0400, Jared Mauch wrote:
The bug is CSCth43783. The control plane comes up but the data
Mike wrote:
Howdy,
This isn't exactly cisco-centric, but it's certainly related operationally.
I operate a county wide isp network and I have about 15 different pops.
I equip each with APC700/1400's and with XR battery packs, with the goal
being around 8 hours of runtime in the event of a
16 matches
Mail list logo
