Re: [c-nsp] Cisco WIC-1DSU-T1-V2 + 2811 + 12.4(11)T ??
Hi I have purchsed 1841 with same wic module .Is this below config work for point to point T1 connection. interface Serial0/0 ip address service-module t1 framing esf service-module t1 linecode b8zs service-module t1 timeslots 1-12 speed 64 Regards Gagandeep Jay Hennigan [EMAIL PROTECTED] wrote: joe mcguckin wrote: I can't get this combination to bring up a T1. Configured as encaps hdlc service-module t1 clock source line service-module t1 line b8zs service-module t1 frame esf service-module t1 timeslots all Indicator LED on WIC is green, with no alarms. Look closely at the jack on the WIC, the molded plastic on the back of where the plug inserts. Does it read STEWART? If not, you have a fake WIC. Even if it does, you might have a fake. -- Jay Hennigan - CCIE #7880 - Network Engineering - [EMAIL PROTECTED] Impulse Internet Service - http://www.impulse.net/ Your local telephone and internet company - 805 884-6323 - WB6RDV ___ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ - Now you can chat without downloading messenger. Click here to know how. ___ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
Re: [c-nsp] Cisco WIC-1DSU-T1-V2 + 2811 + 12.4(11)T ??
gagandeep singh wrote: Hi I have purchsed 1841 with same wic module .Is this below config work for point to point T1 connection. interface Serial0/0 ip address service-module t1 framing esf service-module t1 linecode b8zs service-module t1 timeslots 1-12 speed 64 Only if you are using just half of the T1 for data and you have the same timeslots on both ends. Otherwise you want: service-module t1 timeslots 1-24 speed 64 (which is the default). Also, on a point-to-point circuit depending on the carrier you may need to put: service-module t1 clock source internal on ONE (not both) end of the circuit. -- Jay Hennigan - CCIE #7880 - Network Engineering - [EMAIL PROTECTED] Impulse Internet Service - http://www.impulse.net/ Your local telephone and internet company - 805 884-6323 - WB6RDV ___ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
[c-nsp] Cisco WIC-1DSU-T1-V2 + 2811 + 12.4(11)T ??
I can't get this combination to bring up a T1. Configured as encaps hdlc service-module t1 clock source line service-module t1 line b8zs service-module t1 frame esf service-module t1 timeslots all Indicator LED on WIC is green, with no alarms. Turning on debugging shows no keepalives seen: yourname#debug serial event Serial interface event debugging is on yourname#debug serial interface Serial network interface debugging is on yourname#debug serial packet Serial network packets debugging is on yourname# *Jan 23 22:30:23.227: DTE idb-dte_interface = DTE *Jan 23 22:30:23.227: Dscc4(Serial0/0/0): DCD is up. *Jan 23 22:30:25.227: %LINK-3-UPDOWN: Interface Serial0/0/0, changed state to up *Jan 23 22:30:26.227: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up *Jan 23 22:30:30.391: Serial0/0/0: HDLC myseq 0, mineseen 0, yourseen 0, line up *Jan 23 22:30:40.391: Serial0/0/0: HDLC myseq 1, mineseen 0, yourseen 0, line up *Jan 23 22:30:50.391: gt96k_mbrd_serial_mode_reg_init:: was DTE, now set to DTE *Jan 23 22:30:50.391: DTE idb-dte_interface = DTE *Jan 23 22:30:50.391: Dscc4(Serial0/0/0): DCD is up. *Jan 23 22:30:50.391: Serial0/0/0: HDLC myseq 2, mineseen 0, yourseen 0, line down *Jan 23 22:30:51.391: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to down *Jan 23 22:31:00.391: Serial0/0/0: HDLC myseq 3, mineseen 0, yourseen 0, line down *Jan 23 22:31:10.391: Serial0/0/0: HDLC myseq 4, mineseen 0, yourseen 0, line down *Jan 23 22:31:20.391: Serial0/0/0: HDLC myseq 5, mineseen 0, yourseen 0, line down *Jan 23 22:31:21.391: Serial0/0/0: attempting to restart *Jan 23 22:31:21.391: gt96k_mbrd_serial_mode_reg_init:: was DTE, now set to DTE *Jan 23 22:31:21.391: DTE idb-dte_interface = DTE *Jan 23 22:31:21.391: Dscc4(Serial0/0/0): DCD is up. *Jan 23 22:31:30.391: Serial0/0/0: HDLC myseq 6, mineseen 0, yourseen 0, line down *Jan 23 22:31:40.391: Serial0/0/0: HDLC myseq 7, mineseen 0, yourseen 0, line down no deb all All possible debugging has been turned off If I plug the T1 circuit into a 1760 w- a V1 WIC-1DSU-T1, it comes right up... Any ideas?? Joe Joe McGuckin ViaNet Communications [EMAIL PROTECTED] 650-207-0372 cell 650-213-1302 office 650-969-2124 fax ___ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
Re: [c-nsp] Cisco WIC-1DSU-T1-V2 + 2811 + 12.4(11)T ??
joe mcguckin wrote: I can't get this combination to bring up a T1. Configured as encaps hdlc service-module t1 clock source line service-module t1 line b8zs service-module t1 frame esf service-module t1 timeslots all Indicator LED on WIC is green, with no alarms. Look closely at the jack on the WIC, the molded plastic on the back of where the plug inserts. Does it read STEWART? If not, you have a fake WIC. Even if it does, you might have a fake. -- Jay Hennigan - CCIE #7880 - Network Engineering - [EMAIL PROTECTED] Impulse Internet Service - http://www.impulse.net/ Your local telephone and internet company - 805 884-6323 - WB6RDV ___ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
