Hi all, don't know that this question went out on the list:
Friday I was tuning up my T-4XC on 80M. Heard a very loud POP came from
somewhere behind the front panel. No smell of smoke or oazone.
Never tune for more than 4 or 5 seconds at a time and never off-resonance
more than 1 or 2
I have a Drake T-4XB and the R-4B
Can anyone tell me how to get a side tone when on CW with the receiver in ext
mute position?
- Original Message -
From: drakelist-requ...@zerobeat.net
Date: Monday, February 22, 2010 7:23 am
Subject: Drakelist Digest, Vol 20, Issue 31
To:
If you have a good ANTI-VOX cable connected, and the ANTI_VOX control on
the side of the receiver is at mid-range, you will have sidetone unless
there is a fault in the transmitter or receiver. If the transmitter
functions in TUNE mode, the sidetone generator is working, but there
may be
I need some help locating some power supply cable.. Been looking for some
replacement muilti-conductor cable for a couple of vintage power supplies I'm
restoring but haven't had any luck so far..
Belden sells a bewildering array but I didn't find any cable which has the
mixed sizes of wire
I know that it's a long shot but I would like to purchase a Model 1590 VHF
Converter which installs in the R8/R8A/R8B series of receivers.
If you have one or know of one please contact me off list at
rfch...@verizon.net.
Tnx 73 Ed
Thanks, Gents, for the suggestions on finding a source for power supply cable
replacement.. looks like i'm not the only one who's been searching for same.
It appears that I'll just make up a bundle and run it through a sheath of some
sort.. roll my own.
As always, appreciate the helpful
Hello..I am getting hum only in the AM position and it goes up and down with
the volume control.
I replaced the caps in the high voltage section but not in the 12 volt supply
as they are hard to get at and since I do not hear the hum on SSB I am
assuming, maybe incorrectly, that they are ok.
The Spam Scam
Over the last week, one of the anti-spam databases has my server
listed. We don't spam, but we ended up in the database. The
obnoxious part is that they charge 50 bucks to remove you IF you can
prove you are not violating their rules...so you either pay 50 bucks
or wait 4
The biggest problem is people who post one message to multiple lists then the responder clicks reply all but isn't
subscribed to some lists.
It's sloppy posting by the original sender and an inconsiderate inconvenience
to everybody else.
On 22-Feb-10 21:01, Thom LaCosta wrote:
I'm seeing a
Doc -
Belden has a nice cable, 27341A that looks like it would work. Only
catch is it comes in a 5000 foot reel.!!
Twelve (12) #16 AWG conductors, 600V RMS insulation, multi-color coded
with a silver-gray overall sheath, 0.5 dia.
Let's see, 5000', 10' each, only 500 participants. Unless
Doc
When restoring my L4B and rebuilding the PS I took the opportunity to rebuild
the cable as well - it gave me a chance to take the stiff HV line out and
replace it with a separate HV cable (automotive high tension line works well)
and new matching connector on the PS (right next to the new
I recently bought a nice T-4XC that works fine except for the tuning mechanism.
The dials hang up and don't move sometimes. I took the tuning knob off and
find the brass sleeve slides along the tuning shaft to the PTO allowing the
gears to come un-meshed. Also the shaft turns WAY too freely
Tom -
Start here.
http://www.wb4hfn.com/DRAKE/DrakeArticles/PTO/Drake_PTO.htm
73, Garey - K4OAH
Glen Allen, VA
Drake 2-B, 4-B, C-Line TR-4/C Service Supplement CDs
www.k4oah.com
Tom McDaris wrote:
I recently bought a nice T-4XC that works fine except for the tuning
mechanism. The
At 04:06 PM 02/22/10, Nigel Gunn G8IFF/W8IFF wrote:
The biggest problem is people who post one message to multiple lists
then the responder clicks reply all but isn't subscribed to some lists.
It's sloppy posting by the original sender and an inconsiderate
inconvenience to everybody else.
Even though I've had this TR-4C (#40249) about 2 years I've only just today
took the top cover off for a look. I noticed that the metal shields are
missing from V6 (12BY7A) driver and V12 (12BA6). Is this something I should be
concerned about? Where, if anywhere, can I find replacement
Ken,
Drake stopped installing tubes shields on those tubes a long time ago. The
TR-4C never had them installed.
73, Gary W8PU
http://home.roadrunner.com/~w8pu
___
Drakelist mailing list
Drakelist@zerobeat.net
Hi guys, can you tell me how to unsubscribe from getting the emails, but still
be able to access the archives. My mailbox is filling up but I would still
like to be able to see what's going on by visiting Drakelist. Thank you, I
enjoy all the input from the experts!
Luther, KQ5O
17 matches
Mail list logo