[Dx4win] Elecraft K4D Configuration?
Does anyone have the DX4WIN setup configuration for controlling the Elecraft K4D? Tnx & 73, Mark, K6FG __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Dx4win] DX4WIN + WSJT-X COM Port Control
I have used DX4WIN for many years. I use WSJT-X for FT8. I want both programs to have simultaneous full access to my transceiver through the one COM port that is used for data transfer and control of the transceiver. I have tried many port sharing and port splitting software programs without success. The two programs work for a few minutes, but when one of the programs polls the port, the other program loses connection to the port. Has anyone found a way to do what I want to accomplish? I have been advised that Ham Radio Deluxe has the desired capability, but I don't want to switch from DX4WIN to HRD. Tnx & 73, Mark, K6FG __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Dx4win] DX4WIN, IC7800 & SteppIR Controller Issue
Hello all, I have a strange problem that is driving me nuts. DX4WIN specifies baud rate of 9600 to talk to my IC7800. When I set the IC7800's CI-V baud rate to 9600, there is no communication between DX4WIN and IC7800. When I set the IC7800's CI-V baud rate to AUTO, DX4WIN and IC7800 get along just fine. But, when the IC7800's CI-V baud rate is set at 9600, the SteppIR SDA-100 control box will not autotrack the IC7800's band or frequency. If I set the 7800's CI-V baud rate to AUTO, then the SteppIR SDA-100 control box tracks properly. Does anyone have any ideas? 73 & HNY, Mark, K6FG __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net Message delivered to arch...@mail-archive.com This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Dx4win] DX4WIN and WSJT-X
I've used DX4WIN for many years. It controls my IC-7800 perfectly, as expected. Now I'd like to also be able to control my transceiver by WSJT-X, as well. The problem is that they both fight for control of the rig. DX4WIN usually wins and WSJT-X presents me with an error message. Does anyone have a simple way to enable both programs to control the rig concurrently? Tnx & 73, Mark, K6FG __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net Message delivered to arch...@mail-archive.com This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Dx4win] Rotator issue
Thank you, Dusty. That was the cause. 73, Mark -Original Message- From: Dusty Chapman [mailto:k...@verizon.net] Sent: 5 November, 2017 7:36 AM To: 'Mark Weiss' Subject: RE: [Dx4win] Rotator issue Hi Mark, I had the same problem with my Orion controller. Simple fix for me was - Click on Rotator - Parameters - go to each band and click it and change the "disabled" to "Normal". I think I had to click the OK for each band as I went through the process. Good Luck 73, Dusty - K3WC -Original Message- From: dx4win-boun...@mailman.qth.net [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of Mark Weiss via DX4WIN Sent: Sunday, November 5, 2017 9:55 AM To: DX4WIN@mailman.qth.net Subject: [Dx4win] Rotator issue DX4WIN Ver. 9 does not control my Yaesu rotator (with Idiom Press RS-232 board). Version 8 controlled the rotator properly. Another rotator control program (PstRotatorAz) continues to control the rotator. That is when DX4WIN is shut down to free the COM port. Apparently DX4WIN seizes the COM port. The DX4WIN Ver. 9 rotator settings in Preferences-Control are the same as when I used DX4WIN Ver. 8. >From the above analysis, my guess is that the computer, COM port interface & the rotator are all functioning correctly. Has anyone else experienced this issue? Any suggestions for a fix? Tnx & 73, Mark, K6FG __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net Message delivered to k...@verizon.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html --- This email has been checked for viruses by AVG. http://www.avg.com __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net Message delivered to arch...@mail-archive.com This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Dx4win] Rotator issue
DX4WIN Ver. 9 does not control my Yaesu rotator (with Idiom Press RS-232 board). Version 8 controlled the rotator properly. Another rotator control program (PstRotatorAz) continues to control the rotator. That is when DX4WIN is shut down to free the COM port. Apparently DX4WIN seizes the COM port. The DX4WIN Ver. 9 rotator settings in Preferences-Control are the same as when I used DX4WIN Ver. 8. >From the above analysis, my guess is that the computer, COM port interface & the rotator are all functioning correctly. Has anyone else experienced this issue? Any suggestions for a fix? Tnx & 73, Mark, K6FG __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net Message delivered to arch...@mail-archive.com This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
