--- On Sat, 9/12/09, W0SD Ed Gray w...@triotel.net wrote:
From: W0SD Ed Gray w...@triotel.net
Subject: Re: [Elecraft] [K3] Solar Power
To: Elecraft@mailman.qth.net
Date: Saturday, September 12, 2009, 5:45 PM
Solar power works great and now with the 30% tax incentive you have a real
decent pay
Thanks for all the inquiries. The unit has been spoken for and the
sale is pending.
Bill
W4ISH
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
am i thinking right that k10 grounds during xmit and is open on receive. i
think it's stuck in xmit on mine.
ron
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
I was playing with HRD this afternoon and when swapping bands I ended up on
14 Mc in LSB mode..
I've been trying to get it on USB again but I'm missing something I guess
(and didn't even have a beer this afternoon.)
Where can set the proper mode again?
73's, Evert PA2KW
Problem solved. I think the LSB mode is somewhere disabled for 14 Mc.
By toggling the mode (up) I didn't get the USB Mode. (For some unknown
reason I'm always toggling up until I get what I want).
By toggling down I did get back the USB mode.
Wheird
73's, Evert PA2KW
Evert,
You inadvertently switched to USB. The way to do it by intent is to
hold ALT (yes, the MODE down button (you must have tapped for longer
than a tap).
Only one of the sidebands is shown for any one band - same way for CW
and DATA modes - if you want to change to the opposite sideband,
Hello Don,
It was the software (HRD) that did it for me.
But it's good to see that at the end WE do have control over the radio :-)
73's, Evert PA2KW
-Original Message-
From: Don Wilhelm [mailto:w3...@embarqmail.com]
Sent: Sunday, September 13, 2009 18:13
To: ev...@pa2kw.com
Cc:
And this is the one big reason that I'd recommend the Yaesu over the K3:
user interface.
What do I know, though, I have a K2.
On Sun, 13 Sep 2009, Don Wilhelm wrote:
Evert,
You inadvertently switched to USB. The way to do it by intent is to
hold ALT (yes, the MODE down button (you must
Ron,
It certainly seems that way to me - those are Normally Open contacts and
the relay coil is activated by 12T which is only active during transmit.
Disconnect everything from the Ant jack (J1) and measure the resistance
between the center conductor of J1 to ground - it should be fairly high
I wanted to tell the group about my latest experience with Don Wilheim W3FPR.
I got 2 months ago a fully loaded K2 in very clean condition and even it was
working fairly well,it had some issues with bad alignment having the four
filters not well aligned plus excessive power output on some bands
Interesting comments. I was just wondering one thing, do you really haul
around 16 6v batteries in the back of your pickup? I calculate that is
almost a 1000 pounds of extra weight. Do you use a inverter then to get
120ac for your trailer or what?
regards, Jerry -n6jp-
Don is also a mentor to the builder. He told me how to fine tune the filters
so as to maximise power output for individual band of my K2.
cheers,
Johnny Siu VR2XMC
寄件人﹕ Hector Padron ad4c2...@yahoo.com
收件人 elecraft@mailman.qth.net
傳送日期﹕ 2009 年 9月 14 日 星期一
We have 440 AH of 6V golf cart batteries in our RV. Don't know
what they weigh ... don't care. (:-)
Pretty normal for a solar powered RV. We have no other power
source. They power the K3, lights, vent fans, furnace blower, etc.
and deliver 120 VAC @ 1500 W via a Trace inverter if needed.
I neglected to say that there's 12A of solar panels on the
roof of the RV. There's on other charging equipment as
I removed the battery boiler converter. (;-)
73! Ken Kopp - K0PP
__
Elecraft mailing list
Home:
I turned on my K-3 #3096 today and it seems that the paddle tip input has
stopped working. The sleeve input works FB. I have swapped dits dahs on the
tip/ring in the menu, and the problem stays on the tip input. Checked my
Paddle/cable - all is well there. Before I dive head first into
Don,
Thanks again for the help. I think this is working and I will move ahead. I
just need to install my new KNB2 and I should be ready to get the rig back
in the operating position.
I do not have a major gripe with the KAT-2 directions, but it could use an
update. I have a fair amount of
When I hit the tune button to tune the ATU the beep is unbearably loud. How do
I disable it? I searched the K3 manual, KAT3 manual, the manual erratta and
firmware updates notes and the word 'beep' does not appear anywhere. I can't
find it in the menu and config settings. Help! :-)
Rob
When I hit the tune button to tune the ATU the beep is unbearably loud. How
do I disable it? I searched the K3 manual, KAT3 manual, the manual erratta
and firmware updates notes and the word 'beep' does not appear anywhere. I
can't find it in the menu and config settings. Help! :-)
Good Evening,
Twenty meters had QSB on most callers though it was productive and fair to
most locations. Weather reports were cooling off from what they had been last
week. I even got a report of rain in California! There were sprinkles up here
but not enough to prevent walking outside
Thanks for the quick reply Lyle, that did the trick.
73,
Rob
NV5E
Date: Sun, 13 Sep 2009 19:39:41 -0700
From: k...@wavecable.com
To: roblitesp...@hotmail.com
CC: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KATU3 Beeps
When I hit the tune button to tune the ATU the beep is
Elecraft calls them switch tones.
Set CONFIG:SW TONE=OFF
73
--
Joe KB8AP
On Sep 13, 2009, at 7:21 PM, Rob May wrote:
When I hit the tune button to tune the ATU the beep is unbearably
loud. How do I disable it? I searched the K3 manual, KAT3 manual,
the manual erratta and firmware
My switch tones are off and I don't get beeps any other time, but I guess it
doesn't disable the ATU tuning beeps. Lyle was able to tell me how to turn it
down.
73,
Rob
NV5E
CC: elecraft@mailman.qth.net
From: jp...@jeffnet.org
To: roblitesp...@hotmail.com
Subject: Re: [Elecraft] KATU3
Blazing ahead, I found that RFC3 (100uh choke on the dot input) has opened
up. besides infant part failure, I don't know what could have caused that -
Unless it was my blazing cw speed on the last contest that was more than it
could handle ;)!! Or perhaps they designed in a LID fuse!! Anyway, I
We had a very short and sparse SSB net today on 14.316 MHz. The signal
levels were not very good. We only had 12 participants including net
control and ran for 11 minutes. My apologies to KB9BNI, but I was unable to
pull your rig information through. Here is a list of the 12 participants:
24 matches
Mail list logo
