If this feature is offered in the near future, it would be nice if the
following features were incorporated
into the making the P3 a very useful station tool.
1. Since the Dynamic range is rather limited on the P3, the ability or feature
to allow
1 or 2 crystal notch filters to be inserted
This unit is in great shape and was purchased as a spare. I no longer need it
as we are moving and I will no longer have the need for a spare unit. 100.00
VE3WDM
Mike
__
Elecraft mailing list
Home:
Hi Don,
I had read that note but it is in the current Rev D manual dated 9/30/12
which corresponded to SVGA firmware 1.10. There were two firmware revisions
(1.14 and 1.16) in 2013 each of which added additional notes on 1920x1080
monitor compatibility. Plus the last thread on 1920x1080 monitors
Out of any real estate optimization and the money needed to buy it,
this link may show a needed parent to what we are asking for.
http://www.telepostinc.com/LP-500.html
When delivered, it would have the requested features and even more. Isn't it?
73 de iw1ayd Salvo
PS this
For sale, one PigTail - WiFi remote device for the K3/KX3 which allows remote
control via WiFi using an iPad or iPhone and there is a logging app for the
iPhone/iPad available from them as well. It has a DB9 serial connector on it
and runs on a 9 volt battery.
Originally sold for $124.99 plus
I am really hoping the Sensor port will be used for this! (Soon?)
kc2vmp
On Sep 24, 2013, at 10:09 AM, Bob wb4...@gmail.com wrote:
So I've been loving my P3 for about 2 years now, and I keep looking at that
lonely sensor window in the back, dreaming and wishing
Yesterday I received an
What is the unmatched SWR? The KAT3 operates at far lower power than the
KAT500, and it can safely handle an extremely wide SWR range. We have to be
more conservative in what we match at 500 W+ to avoid arcing or component
damage.
If the KAT500 isn't finding a good match for a low/medium SWR
As your post indicates, the splattering of JT65 signals has most likely
nothing to do with your transmitter and setup. It is more likely to be due
to the specifics of the JT65 display/decoding algorithm than anything else.
I have done spectral estimation for some 30+ years and it reminds me very
The PigTail has been spoken for.
_
For sale, one PigTail - WiFi remote device for the K3/KX3 which
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
If your neighbor tells you it's clean (and s/he knows how to look) then it's
likely the other station at fault. Noise blanking, noise reduction, poor RX
audio (over)driving are huge issues that can make any reception look bad.
Bottom line: don't sweat it if your local stations tell you
Hi ! I've a similar issue but in my case it comes from the cabling I feel.
My KAT is directly connected to antenna incoming bur k3 has extra 2,5 meters
of RG 58 (1 meter patch from KAT to switch plus 1,5 meters patch from the
switch to k3).
In my situation and only in some bands I have differents
FWIW, overload from a strong local signal can cause much weaker signals to
behave this way. Once amplifier stages in a receiver are driven into
overload, they produce all sorts of mixing products with any signal coming
through. The overloading signal may have been far off frequency, even on
This is good to know. I had this same experience on PSK31, and it was trouble
at the receiving end because it was happening on other signals as well, while
other stations gave me a clean bill of health. I didn't know if it was his
soundcard, software, or interface.
Dick, n0ce
- Original
That clears up something that has bothered me on JT65. Many times
someone will complain about someone overdriving, but the signal appeared
to be OK to me. It happens frequently. Now I think the complainer is
probably receiving the station much more strongly than I am and it is
overdriving his
Well nothing would put the issue to bed better than a nice printout of a P3
screen that was sampling the RF signal over a bandwidth of about 6KHz.
That's why I would LOVE for Elecraft to continue developing the P3 and
expanding its capability.
I don't mind the report, and I take it seriously,
Yep, that is 100% correct.
If the station that is offended would simply reduce their RF gain control,
in most cases they will see the signal clean right up. Then the real issue
is that they want to copy a weak signal that is in a chunk of spectrum that
is full of strong signals (most likely due
Any thoughts as to when the 2 meter option might come out for the KX3?
--
Mike Herr
WA6ARA
DM-15dp
Home of The QRP Ranch
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Hi Mike, The SVGA card uses an embedded VGA controller. This means that we're
limited to two possible pixel clocks for the 1920x1080 resolution. Some
monitors cannot sync to the pixel clocks and this causes the display to show
the two black areas you noticed.Try setting manual mode on your
I have acquired a Yamaha CM 500 headset to use with my newly built K2sb.
I've looked through the archives and found an in line resistor is required.
My question is how to set the jumpers on the front panel board.
Tom
KI6NRD
K2 # 7432
__
K3/0 forsale with leads to connect to rig remote box .
Contact g3...@btinternet.com
Sent from Samsung Mobile
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
My normal technique with sound card modes (mostly PSK31) is to
look at the audio AtoD overload indicator in my software and
reduce the RF gain so it indicates no overload. This procedure
uses the minimum necessary gain through most of the radio/AtoD
etc, limiting local distortion products. It
Tom,
My question is how to set the jumpers on the front panel board.
Set the jumpers/resistor exactly as recommended for the Elecraft
MH2 microphone.
73,
... Joe, W4TV
On 9/25/2013 1:51 PM, Tom Field wrote:
I have acquired a Yamaha CM 500 headset to use with my newly built K2sb.
I've
Tom,
You can set the jumpers just like for the Elecraft microphones - all
straight across. You will also need a bias resistor between pin 6 and
pin 1 at the back of the mic jack - 5.6k will do fine.
You will also need an adapter to go between the 3.5mm plug on the CM500
to the 8 pin Foster
Hi all,
Just to let you all know the information below. The expedition will have 5
K3's, 3 KPA500's and a couple of P3's amongst the kit. We would love to
work you all :)
Members of the Mayo Radio Experimenters Network in conjunction with the
Sands Contest Group and the Workington Amateur Radio
Thanks folks for all the effort getting us QRP folks checked in last Sunday. It
is much appreciated and further enhances the team support feeling I get from
the mailing group (and Elecraft in general). I am glad I bought into the
Elecraft universe.
Aloha,
Dave
K6WDE/KH6
Hi Ian,
According to Google Earth, it looks like you are going to have a GREAT ocean view to
the west! You will be there during the best days of the month for 6m EME, and I
know there are 6m stations over here who would love to work you during yoru moonset
;-) I know you have great
Hi Lance,
I'm sorry but this will probably be an HF expedition. We have no aerials
for 6m other than a StepIR vertical. Maybe another time.
73 Ian
--
Ian J Maude, G0VGS
SysOp GB7MBC HB9DRV-9 DX Clusters
If you feel you would like to donate to help the running of the cluster,
please visit
I am still having problems getting relays when I try to check in. But it is
getting better. Will keep trying on Sundays that I can check in. Sometimes
tied up with things related to my wife's traumatic brain injury and can't check
in.
73 de Dave KJ6CBS
Dave,
I am sorry to hear about your wife's injury.
I note that we used to get you checked in a lot more. I wonder what we were
doing differently then. Maybe I should beam south a bit more.
See you soon.
73,
Phil, NS7P
On Sep 25, 2013, at 2:01 PM, David Guernsey mooo1...@yahoo.com wrote:
The antenna has been sold
Mike
VE3WDM
--
View this message in context:
http://elecraft.365791.n2.nabble.com/LF-engineering-H-900-active-antenna-for-sale-tp7578961p7579250.html
Sent from the Elecraft mailing list archive at Nabble.com.
The LDG antenna switch has been sold.
Mike
VE3WDM
--
View this message in context:
http://elecraft.365791.n2.nabble.com/For-sale-LDG-6-position-antenna-switch-tp7579222p7579249.html
Sent from the Elecraft mailing list archive at Nabble.com.
The KRX3 has been sold
Mike
VE3WDM
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KRX3-and-filters-for-sale-tp7578933p7579251.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing
Ok, just got my Side KX plates and cover. Installed them and looks great.
Now, what to do with the old plates? Keep them? (I will only lose them)
Does Elecraft want them? (drop them off at Pacificon).
--
Mike Herr
WA6ARA
DM-15dp
Home of The QRP Ranch
My new K160RX kit for the K2 is no longer available.
Tnx es 73
Don W9CW
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This
...so there I am tuning across 20 meters and the band seems dead.
Having learned a lot about self-fulfilling prophesies across my 53 year
ham career, I go up to 14.060 and send one quick CQ.
A tiny signal appears but the KX3 has what it takes to make the most of
the situation. I manage to
That is the coolest!!! and QRP did it again... that a couple of good ops
too!Congratulations Stan!!
Have a great day,
--... ...--
Dale - WC7S in Wy
Date: Wed, 25 Sep 2013 21:21:53 -0400
From: sjl...@optonline.net
To: Elecraft@mailman.qth.net
Subject: [Elecraft] [OT] The Joy of
Y'know, most of the DX I work is on dead bands, usually 20 meters for me.
I'll tune up and down for a few minutes hearing absolutely no one. So I find a
quiet spot.
Not always, of course, but often enough that I'm no longer surprised a DX
station calls me sometimes from halfway around the
37 matches
Mail list logo
